首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 453 毫秒
1.
建立了脉冲-辉光放电质谱(Pulsed-GDMS)测定稀土合金中7种关键元素Mg、Fe、Cu、La、Ce、Pr、Nd的分析方法。系统考察了脉冲时间、样品均匀性、质谱仪配件(阳极帽、导流管、样品锥)、压片致密性对测量重复性的影响。对于含量在mg/g量级以上的元素,影响重复性(RSD)的最大因素是质谱仪配件的更换,不更换配件RSD3%,更换新配件RSD为2%~11%,更换重复使用的旧配件RSD为3%~21%;其次是粉末样品压片的致密性,致密样品的测量结果 RSD3%,致密性越低,测量重复性越差。采用高分辨电感耦合等离子体质谱(HR-ICP-MS)对1#稀土合金样品中的元素进行测量,以测量值为参考值对Pulsed-GDMS的测量结果进行校正,获得各元素的相对灵敏度因子,用校正后的Pulsed-GDMS对2#稀土合金样品进行测定。结果表明,对于致密样品(2#-A)的Pulsed-GDMS分析结果与HR-ICP-MS分析结果一致。在优化的条件下,实际样品测量结果的扩展不确定度可降低至3%~10%。  相似文献   

2.
通过对常用粘结剂中杂质元素含量的测定,选择硬脂酸做粘结剂,研磨压片制备样品,用X射线荧光光谱仪(XRF)测定铝用炭素阳极材料中硫、钒、钠、钙、硅、铁、镍、钛、铝、镁、磷、铅、锌、铬、锰含量的元素含量。通过实验确定了最佳的样品和粘结剂比例为12 g炭素试样加入2 g硬脂酸,研磨时间为20 s。测定铅元素时,选择一点法扣除背景,通过谱线强度数据确定使用PbLβ1做分析线。用铝用炭素阳极材料系列标准样品制作校准曲线,用铑靶康普顿散射内标校正铁、镍、铅、锌、铬、锰等元素,其余元素用经验系数法校正。样品精密度试验表明,样品中各元素测定结果的相对标准偏差(RSD,n=11)一般在8%以下,最高的钠元素和钛元素也在10%左右,未知样品的检测结果与标准结果没有显著性差异。  相似文献   

3.
利用微波消解-电感耦合等离子体质谱法(ICP-MS)测定海洋藻类食品中铅、镉的含量。样品经过微波消解,在线加入内标校正基体效应,通过修正方程校正质量数干扰。各元素校正曲线的相关系数均大于0.9998,样品分析结果的相对标准偏差均小于3%(n=6),加标回收率在80.5%~101.5%之间。方法可用于海洋藻类食品中铅、镉含量的测定和监控。  相似文献   

4.
采用HCl-HNO_3-HF-HClO_4四种酸溶解铅锌精矿样品,稀释后用电感耦合等离子体原子发射光谱(ICP-AES)法测定其中的铊元素,测定范围0.005%~0.05%。实验确定了介质酸浓度、干扰元素的校正方法。方法相对标准偏差(n=7)为1.3%~4.8%,加标回收率为93.7%~102%,方法干扰少、快速、结果准确,适用于大批量铅锌精矿样品中铊的测定。  相似文献   

5.
电感耦合等离子体质谱测定地质样品中多种元素   总被引:10,自引:0,他引:10  
用电感耦合等离子体质谱(ICP-MS)测定了地质样品中多种元素。考察了测量过程中的基体效应及质谱干扰,利用In内标,补偿由于基体效应的影响所引起的测量偏差,建立校正公式校正质谱干扰。方法的检出限为0.06~250ng/L,精密度为1.7%~3.2%,加标回收率为91%~108%,方法适于批量地质样品分析。  相似文献   

6.
ICP-MS测定紫菜中的总砷   总被引:1,自引:0,他引:1  
采用电感耦合等离子体质谱(ICP-MS)法,对紫菜中的微量元素砷进行了测定。用HNO3-H2O2混合体系分解样品,通过在线加入内标元素校正基体效应和接口效应,通过EPA 200.8干扰校正方程校正质量数干扰。校正曲线的相关系数大于0.999 9,As的检出限(3σ)为0.021μg.L-1,样品分析结果的相对标准偏差3.7%(n=6),加标平均回收率为96.0%。通过测定贻贝标准物质GBW 08571验证了该方法的准确性。  相似文献   

7.
通过对常用黏结剂中杂质元素含量的测定,选择硬脂酸作黏结剂,研磨压片制备样品,用X射线荧光光谱(XRF)法测定铝用炭素阳极材料中硫、钒、钠、钙、硅、铁、镍、钛、铝、镁、磷、铅、锌、铬、锰的含量。通过实验确定了最佳的样品和黏结剂比例为12g炭素试样加入2g硬脂酸,研磨时间为20s。测定铅元素时,选择一点法扣除背景,通过谱线强度数据确定使用PbLβ1作分析线。用铝用炭素阳极材料系列标准样品制作校准曲线,用铑靶康普顿散射内标校正铁、镍、铅、锌、铬、锰等元素,其余元素用经验系数法校正。精密度实验表明,样品中各元素测定结果的相对标准偏差(RSD,n=11)一般在8%以下,最高的钠元素和钛元素也在10%左右,未知样品的检测结果与标准结果没有显著性差异。  相似文献   

8.
建立了电感耦合等离子体原子发射光谱(ICP-AES)法测定镧玻璃废粉中稀土元素总量和配分量的分析方法。样品经碱熔融后分离硅、铝等元素及钠盐,用硝酸和高氯酸破坏滤纸和溶解沉淀,用ICP-AES法测定稀土元素总量和配分量。讨论了溶解样品条件、共存元素干扰等影响测定的各种因素。实际样品的稀土总量与草酸盐重量法测定结果一致,配分量与X-射线荧光光谱(XRF)法、电感耦合等离子体质谱(ICP-MS)法测定结果一致。RSD(n=11)在0.15%~1.1%,加标回收率为97%~105%。测定范围为:La_2O_3/REO(80%~98%);CeO_2/REO(2%~20%);REO(16%~70%)。方法能快速准确地测定镧玻璃废粉中稀土元素总量及配分量。  相似文献   

9.
采用微波消解-电感耦合等离子体质谱法同时测定土壤中砷、镉、铬、铜、汞、镍、铅、锌8种痕量元素,对质谱干扰和非质谱干扰进行了校正。8种重金属元素在一定的质量浓度范围内与其信号强度呈线性关系,方法的检出限(3s)在0.001 2~0.029μg/L。用加标回收测定其回收率,加标回收率范围在90.0%~96.3%,对土壤样品平行测定6次,测定值的相对标准偏差在2.1%~3.0%。对湛江南柳河附近土壤进行重金属监测,监测结果符合标准要求。  相似文献   

10.
用支持向量回归方法(SVR)建立校正模型,并对维生素B1、B2和B6的模拟样品进行测定。结果表明,维生素B1、B2和B6预测结果的回收率在96%~104%之间,测定结果准确。  相似文献   

11.
用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.  相似文献   

12.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

13.
A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.  相似文献   

14.
The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp3)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp2)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp2)?H and aliphatic 1,5- and 1,6-C(sp3)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp3)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp2)?H insertion.  相似文献   

15.
The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.  相似文献   

16.
KMnO4-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.  相似文献   

17.
The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.  相似文献   

18.
The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.  相似文献   

19.
N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).  相似文献   

20.
An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y1 and Y2. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号