Au Nanowires-MWCNTs修饰电极对葡萄糖的催化氧化

通过油胺(Oleylamine)还原法制备了金纳米线(Au nanowires),将其与酸化处理的多壁碳纳米管(MWCNTs)通过层层组装制备了Au nanowires-MWCNTs复合结构修饰的玻碳电极(Au nanowires-MWCNTs/GCE).电化学研究结果表明,与单纯Au nanowires或MWCNTs修饰电极相比,Au nanowires-MWCNTs/GCE对葡萄糖表现出更优良的电催化性能.以Au nanowires-MWCNTs/GCE为阳极,电沉积Pt膜电极(Pt/GCE)为阴极,构建了葡萄糖/O2燃料电池.测试结果表明,构建的燃料电池的开路电位(OCP)为0.57 V,在0.44 V下最大功率密度(Pmax)为0.28 m W/cm2.     

钛基纳米多孔金电极对甲醛氧化的电催化活性

采用水热法制备了钛基纳米金微粒修饰电极(Au/Ti)。扫描电镜图表明纳米金颗粒粒径大约为300 nm,在钛基体表面构成三维多孔网状结构。运用循环伏安,电位阶跃和交流阻抗等电化学技术研究了碱性介质中甲醛在Au/Ti电极上的电氧化行为。循环伏安图显示,甲醛在Au/Ti上的起始氧化电位在-0.90 V左右,相对于多晶金电极提前大约0.2 V,交流阻抗测试表明,甲醛在Au/Ti电极上电氧化表现出低的电荷传递电阻。研究结果表明钛基纳米金微粒修饰电极对甲醛氧化具有良好的电催化活性。     

聚脱氧腺苷酸/还原石墨烯纳米复合膜电化学传感器检测核黄素

以含32个碱基的聚脱氧腺苷酸(A32)作为黏合剂,将水合肼还原的石墨烯(RGO)固定在金(Au)电极表面,制备A32/RGO纳米复合膜电化学传感器.利用循环伏安法和交流阻抗法对传感器制备过程进行表征,并用循环伏安法和微分脉冲伏安法研究了该传感器的电化学行为.研究结果表明,与裸Au电极和A32修饰的Au电极相比,RGO/A32/Au电极对核黄素有较高的电化学活性,其还原峰电流与核黄素的浓度在0.025~2.75μmol/L范围内呈线性关系,检出限(S/N=3)为15 nmol/L.该传感器具有灵敏度高、抗干扰能力强及稳定性好等优点,可用于人尿中核黄素的分析测定.     

Au@Pt纳米粒子催化O2还原反应的电化学研究

以100 nm的Au粒子为核,抗坏血酸为还原剂,H2PtCl6·6H2O为前驱体,合成了Pt包Au核壳结构纳米粒子( Au@ Pt)及其修饰的玻碳(GC)电极(Au@ Pt/GC).采用旋转圆盘电极等常规电化学方法,比较了Au@ Pt/GC和商用碳载铂(Pt/C)修饰的玻碳电极(Pt/C/GC)催化O2还原反应活性及耐甲醇性能,发现Au@ Pt纳米粒子在铂用量很低的情况下,其催化O2还原反应活性仍与商用Pt/C相当,而且还具有优良的耐甲醇性能;其催化O2还原反应机理按O2直接还原成H2O的四电子历程进行.     

无金属可见光诱导原子转移自由基聚合法制备聚丙烯酰胺@氧化石墨烯/纳米钯复合物修饰电极及其对乙醇的检测

在金电极表面,用无金属可见光诱导原子转移自由基聚合(MVL ATRP)的方法制备聚丙烯酰胺@氧化石墨烯/纳米钯复合物修饰电极(Au/PAM@GO/Pd)。采用电化学循环伏安法(CV)、交流阻抗法(EIS)、扫描电子显微镜(SEM)、能量色散X射线光谱法(EDS)对Au/PAM@GO/Pd电极进行表征,结果表明在金电极表面成功制备了复合物。利用Au/PAM@GO/Pd电极作为电化学传感器,该传感器能成功地检测溶液中的乙醇。在最佳条件下,利用差分脉冲伏安法(DPV)该传感器检测乙醇的线性范围为1.0×10-8~1.0 mol/L,检出限(S/N=3)为1.3×10-9 mol/L,线性相关系数为0.996。     

电化学石英晶体微天平研究碱性介质中单层级铂原子修饰的金电极上甲醇的电催化氧化

通过在Au电极表面欠电位沉积(UPD)Cu、再与Pt源(H2PtCl6或K2PtCl4)进行置换反应,制得单层级Pt原子修饰的金电极(对H2PtCl6或K2PtCl4,所制电极分别记为Pt(CuUPD-Pt4+)n/Au或Pt(CuUPD-Pt2+)n/Au,n表示欠电位沉积-置换过程的重复次数).用电化学石英晶体微天平(EQCM)技术定量研究了所制电极,评估了其在碱性环境中催化甲醇氧化的质量比活性(SECA).结果表明,以H2PtCl6为Pt源所制电极(Pt(CuUPD-Pt4+)3/Au)的活性更高,最大SECA高达35.7mAμg-1.根据EQCM结果计算了置换效率,籍此讨论了Pt原子在Au电极表面的层层组装结构,发现所制电极表面的裸Au位点分布百分数与实验结果(由AuOx还原峰电量测算)吻合.我们认为,EQCM技术是一种定量研究电极支撑的超薄催化剂的有效手段,这种高效的单层级贵金属催化剂有望在生物、能源、环境相关的电催化研究中进一步应用.     

生物素衍生物自组装膜制备及其覆盖度的电化学测定

利用循环伏安法和电化学交流阻抗谱研究了MBDA/Au,MBTA/Au,TBDA/Au,TBTA/Au修饰电极以及MBDA与DT混合自组装/Au、TBTA与DT混合自组装/Au修饰电极的覆盖度。结果表明这些自组装膜在金电极表面的覆盖度均比较高,达到99%以上;对同一类修饰电极,混合自组装膜的覆盖度高于单组分自组装膜的覆盖度,混合自组装体系的覆盖度随着DT比例的增加而增加;同类物质,长链化合物在金表面的覆盖度大于短链化合物,含二硫键的化合物与金电极的键合能力比含一个巯基的化合物键合能力强。     

Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

Ho~(3+)修饰的Pt/C电极对DMM的电催化氧化

通过循环伏安法(CV),计时电流法(CA)和线性扫描法(LSV)对二甲氧基甲烷的电氧化特性进行了研究.发现当用Ho3+修饰Pt/C催化剂电极后可以大幅度提高电极对DMM的电催化活性.热处理Ho3+修饰后Pt/C催化剂电极,可进一步提高该电极对DMM的电催化氧化活性.     

Study on Electrochemical Behavior of Controllable Interface Alkanethiols Selfassembled Monolayers and Au Nanoparticles Modified Gold Electrode

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜( MTP+ TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+ TA/Au).研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响.对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究.     

Studies on Electrochemical Behavior of Bleomycin and Its Interaction with DNA at a Co／GC Ion Implantation Modified Electrode

ＩｎｔｒｏｄｕｃｔｉｏｎＩｏｎｉｍｐｌａｎｔａｔｉｏｎｉｓａｋｉｎｄｏｆｎｅｗｍａｔｅｒｉａｌｓｕｒｆａｃｅｍｏｄｉｆｉｃａｔｉｏｎｔｅｃｈｎｉｑｕｅ .Ｒｅｃｅｎｔｌｙ ,Ｌｉｅｔａｌ .1ｈａｖｅｌｅｄｔｈｉｓｔｅｃｈｎｉｑｕｅｉｎｔｏａｎａｌｙｔｉｃａｌｃｈｅｍｉｓｔｒｙａｎｄｍａｄｅｍｏｄｉ ｆｉｅｄｅｌｅｃｔｒｏｄｅｗｉｔｈｐａｒｔｉｃｕｌａｒｆｕｎｃｔｉｏｎ .Ｉｔｈａｓｂｅｅｎａｐ ｐｌｉｅｄｔｏｓｔｕｄｙｔｈｅｅｌｅｃｔｒｏｃｈｅｍｉｃａｌｂｅｈａｖｉｏｒｓａｎｄｔｈｅｄｅ ｔｅｒｍｉｎａｔ…     

博莱霉素与DNA在镍离子注入修饰电极上的相互作用 及其应用

博莱霉素(BLM)在0.1mol/LHOAc-NaOAc缓冲溶液(pH4.62)中,在Ni/GCE离子注入修饰电极上有一灵敏的还原峰,峰电位为-1.16V(vs.SCE),峰电流与BLM浓度有关。用线性扫描和循环伏安法研究体系的行为表明,体系为具有加速作用的不可逆过程,是注入的Ni加速BLM的还原。引入DNA后,BLM的峰电位为-1.15V(vs.SCE),与未加入DNA前几乎完全一致;只使峰电流降低,形成一种非电活性的结合物,求得该结合物的结合比为BLM：DNA=3：1,结合常数为β=3.16×10^16,用线性扫描和循环伏安法,并辅以紫外可见光谱法等手段研究表明,电极过程仍为不可逆过程,与未加入DNA时一样。加入DNA后,BLM的峰电流降低,可用于DNA的测定,回收率在96.8～103.9%之间.     

Mediated Electron Transfer Across Supported Bilayer Lipid Membrane with TCNQ‐Based Organometallic Compounds

Supported bilayer lipid membrane (s‐BLM) containing one‐dimensional compound 1, TCNQ‐based (TCNQ=7,7,8,8‐tetracyanoquinodimethane) organometallic compound {(Cu₂(μ‐Cl)(μ‐dppm)₂)(μ₂‐TCNQ)}_∞, was prepared and characterized on the self‐assembled monolayer (SAM) of 1‐octadecylmercaptan (C₁₈H₃₇SH) deposited onto Au electrode. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) results showed that the compound 1, dotted inside s‐BLM, can act as mediator for electron transfer across the membrane. Two redox peaks and the charge‐transfer resistance of 400 kΩ were observed for compound 1 inside s‐BLM. The mechanism of the electron transfer across s‐BLM by TCNQ is by electron hopping while TCNQ‐based organometallic compound is by conducting. Further conclusion drawn from this finding is that the TCNQ‐based organometallic compound embedded inside s‐BLM exhibits excellent electron transfer ability than that of free TCNQ. This opens a new path for the development of s‐BLM sensor and/or biosensor by incorporation with TCNQ‐based organometallic compounds.     

On Oxygen‐Containing Groups in Chemically Modified Graphenes

Reduced graphenes (belonging to the class of chemically modified graphenes, CMG) are one of the most investigated and utilized materials in current research. Oxygen functionalities on the CMG surfaces have dramatic influences on material properties. Interestingly, these functionalities are rarely comprehensively characterized. Herein, the four most commonly used CMGs, mainly electrochemically reduced graphene oxide (ER‐GO), thermally reduced graphene oxide (TR‐GO), and the corresponding starting materials, that is, graphene oxide and graphite oxide, were comprehensively characterized by a wide variety of methods, such as high‐resolution X‐ray photoelectron spectroscopy, electrochemical impedance spectroscopy, UV/Vis spectroscopy, transmission electron microscopy (TEM), and voltammetry, to establish connections between the structures of these materials that carry different oxygen functionalities and their electrochemical behaviors. This was followed by the quantification of the negatively charged oxygen‐containing groups (OCGs) by UV/Vis spectroscopy and of the electrochemically reducible OCGs by voltammetry. Lastly, a biofunctionalization with gold nanoparticle (AuNP)‐modified DNA sequences was performed by the formation of covalent bonds with the carboxylic groups (? COOH) on the CMG surfaces. There was an evident predominance of functionalizable ? COOH groups on the ER‐GO surface, as confirmed by a higher amount of Au detected both with differential‐pulse voltammetry and impedance spectroscopy, coupled with visualization by TEM. We exploited the DNA–Au bioconjugates as highly specific stains to localize and visualize the positions of carboxylic groups. Our findings are very important to clearly identify the presence, nature, and distribution of oxygen functionalities on different chemically modified graphenes.     

A Colloidal Au Monolayer Modulates the Conformation and Orientation of a Protein at the Electrode/Solution Interface

The orientation and conformation of adsorbed cytochrome c (cyt c) at the interface between an electrode modified with colloidal Au and a solution were studied by electrochemical, spectroscopic, and spectroelectrochemical techniques. The results indicate that the colloidal Au monolayer formed via preformation of an organic self‐assembled monolayer (SAM) can increase the electronic coupling between the SAM and cyt c in the same manner as bifunctional molecular bridges, one functional group of which is bound to the electrode surface while the other interacts with the protein surface. The approach of cyt c to the modified electrode/solution interface can be assisted by strong interactions of the intrinsic charge of colloidal particles with cyt c, while the heme pocket remains almost unchanged due to the screening effect of the negatively charged field created by the intrinsic charge. The conformational changes of cyt c induced by its adsorption at a bare glassy carbon electrode/solution interface and the effect of the electric field on the ligation state of the heme can be avoided at the colloidal‐Au‐modified electrode/solution interface. Finally, a possible model for the adsorption orientation of cyt c at the colloidal‐Au‐modified electrode/solution interface is proposed.     

还原剂对Au-Pd/CeO2催化剂甲醇部分氧化性能的影响

以PVP为保护剂,乙醇(ER)、乙二醇(GR)和水合肼(HR)为还原剂制备了一系列Au-Pd/CeO2催化剂,考察了还原剂对甲醇部分氧化性能的影响,并运用XRD、TPD和TPR等手段对催化剂进行了表征。结果表明,Au-Pd/CeO2(ER)催化剂具有较大的比表面积,形成的AuxPdy量较多、粒径较小、分散度较高、活性组分与载体的相互作用较强,同时对甲醇的吸附量较大和吸附温度较低。因此,该催化剂具有较高的催化活性和氢气选择性以及较低的CO质量分数。     

Sensitive determination of dopamine in the presence of uric acid and ascorbic acid using TiO2 nanotubes modified with Pd, Pt and Au nanoparticles

A simple modified TiO(2) nanotubes electrode was fabricated by electrodeposition of Pd, Pt and Au nanoparticles. The TiO(2) nanotubes electrode was prepared using the anodizing method, followed by modifying Pd nanoparticles onto the tubes surface, offering a uniform conductive surface for electrodeposition of Pt and Au. The performance of the modified electrode was characterized by cyclic voltammetry and differential pulse voltammetry methods. The Au/Pt/Pd/TiO(2) NTs modified electrode represented a high sensitivity towards individual detection of dopamine as well as simultaneous detection of dopamine and uric acid using 0.1 M phosphate buffer solution (pH 7.00) as the base solution. In both case, electro-oxidation peak currents of dopamine were linearly related to accumulated concentration over a wide concentration range of 5.0 × 10(-8) to 3.0 × 10(-5) M. However in the same range of dopamine concentration, the sensitivity had a significant loss at Pt/Pd/TiO(2) NTs electrode, suggesting the necessity for Au nanoparticles in modified electrode. The limit of the detection was determined as 3 × 10(-8) M for dopamine at signal-to-noise ratio equal to 3. Furthermore, the Au/Pt/Pd/TiO(2) NTs modified electrode was able to distinguish the oxidation response of dopamine, uric acid and ascorbic acid in mixture solution of different acidity. It was shown that the modified electrode possessed a very good reproducibility and long-term stability. The method was also successfully applied for determination of DA in human urine samples with satisfactory results.     

槲皮素修饰的双层脂膜的伏安研究

槲皮素修饰的从层脂膜作为研究抗病毒药物的一种模型体系,用循环伏安法测定了槲皮素在脂膜界面上的氧化还原性质和配位性质。在电位扫描过程中,微量铜离子能催化槲皮素的氧化,当双层脂膜的两侧存在着合适的氧化还原偶时,就会产生跨膜的电子传递。     

Evaluation of a glassy carbon electrode modified by a bilayer lipid membrane with incorporated DNA

The objective of the present work was the evaluation and characterization of a glassy carbon (GC) electrode modified by a bilayer lipid membrane (BLM) with incorporated single-stranded deoxyribonucleic acid fss DNA). Various procedures were developed and tested for the incorporation of ss DNA at the electrode modified by the lipidic membrane: Differential pulse voltammetry (i.e. oxidation of guanine and adenine residues) was used to monitor the incorporation of ss DNA at the GC electrode modified by the BLM. The results have shown that the lipid membrane enhances the stability of ss DNA during a "medium-exchange" of the electrode and prohibits its diffusion from the electrode surface. The third scheme was proven to be the most appropriate as both electrode modification by the BLM and DNA adsorption occur in one stage and much faster (as no BLM thinning process is required) as compared to the former two techniques; furthermore, maximized loading of DNA in BLMs is achieved which reduces by ca. 10-fold the DNA amounts that can be detected electrochemically. Conventional planar "free-suspended" and self-assembled metal supported BLMs were used to monitor in situ the incorporation of ss DNA in these membranes. The results have shown that the adsorption of ss DNA at lipid membranes (as a medium for DNA incorporation on an electrode surface) can occur much faster, using milder conditions and smaller amounts of DNA than by previously described techniques.     

Examination of bilayer lipid membranes for 'pin-hole' character

BLM prepared on electrode substrates by supporting or tethering were tested for 'pin-hole' character, comparing data from cyclic voltammetry (CV), surface plasmon resonance (SPR) and rotating disc electrodes (RDE). 1-hexadecylamine tethered BLMs on SAM modified gold electrodes were compared with BLMs assembled on modified polyHEMA or sol-gel layers. BLM formation followed by SPR showed that the initial phase of the assembly was complete in 5-20 minutes and produced layers of thickness >5 nm, compared with the expected final BLM thickness of approximately 3 nm. The CVs of the K(3)[Fe(CN)(6)] couple were significantly suppressed irrespective of the method of BLM assembly, without major differences emerging for the different methods. However, data from the RDE distinguished the 'pin-hole' character of the different preparations. The data were consistent with incomplete initial (<1 h, SPR estimated BLM thickness >5 nm) vesicle fusion leaving 'pin-holes' of approximately 2 microm (HDA-11-mercaptoundecanoic acid (MUA) tethered BLM) to approximately 3 microm (tetraethylorthosilicate sol-gel supported BLM) followed by a slow maturation (>15 h; impedance spectroscopy estimated thickness approximately 3 nm) and lateral spreading and fusion, resulting in loss of 'pin-hole' character (<1 microm). The BLM could be used in conjunction with potentiometric measurement to observe the incorporation of nystatin into the BLM and the rate of incorporation adjusted according to original permeability of the BLM. The 'pin-hole-free' BLM construction with lowest permeability (TEOS supported, 4 x 10(-10) cm s(-1) compared with HDA-MUA, 3 x 10(-9) cm s(-1)) gave a potentiometric signal independent of bulk ion-concentration across 5 decades change in concentration. Formed on an ion-selective electrode, nystatin incorporation could be followed as a change in potential, over >2 h, whereas the TEOS supported BLM with permeability 1 x 10(-9) cm s(-1) shows nystatin incorporation within 1 h. In this instance, addition of ConA reduced the potential to the same value as prior to nystatin incorporation, consistent with nystatin channel closure.