间接电氧化法合成甘油醛

通过电化学合成前驱体和溶胶-凝胶法在Ti表面修饰一层纳米TiO2膜,在纳米Ti02膜上电沉积分散的Pt微粒制成钛基纳米TiO2-Pt(Ti/nano-TiO2-pt)修饰电极。采用循环伏安法、间接电氧化法研究了纳米Ti02-Pt修饰电极的电催化活性以及Mn^3 ／Mn^2 媒质氧化甘油为甘油醛的过程。结果表明,纳米Ti02-Pt修饰电极对Mn^2 的电氧化具有高催化活性,电流效率可达90％以上,非均相电解得到的Mn^3 可一步氧化甘油为甘油醛,收率为91％。     

纳米钯催化剂对甲醇的电催化氧化

采用水热法,以甲醛作还原剂还原Pd2+-EDTA络合物,制得钛基纳米钯颗粒电极(nanoPd/Ti).扫描电子显微镜(SEM)显示,纳米钯颗粒直径约为60 nm,形成三维立体网状结构.在碱性溶液中,循环伏安及交流阻抗测试分别表明:nanoPd/Ti电极对甲醇氧化有极高的阳极电流、较低的起始氧化电位和较强的抗CO毒化能力.在nanoPd/Ti电极上甲醇电氧化反应的阻抗值较低,增加甲醇浓度,电极阻抗更低.电极对甲醇氧化具有极好的电催化活性.     

nano-Au/POPD/Au电极对甲醛的电催化氧化及检测

采用连续循环伏安法在金电极上制备了纳米金聚邻苯二胺膜修饰电极(nano-Au/POPD/Au),并研究了不同修饰电极在碱溶液中对甲醛的电催化氧化性能。结果发现,nano-Au/POPD/Au电极对甲醛具有高的催化活性和稳定性,在峰电位0.3 V处产生的电催化电流比nano-Au/Au电极上产生的高2.1倍。考察了纳米金的负载量(扫描圈数和扫描速率)、扫描速率、NaOH浓度等参数对甲醛催化氧化的影响。在优化条件下,甲醛在质量浓度0.1~600 mg/L范围内呈良好线性,检出限(S/N=3)为0.01 mg/L。将该方法应用于红酒和Skiphop儿童塑料餐碟中甲醛含量的测定,结果与标准乙酰丙酮法一致。     

新型的钛基Ni-Sn/Ti电极的制备及对甲醇氧化反应的电催化活性

利用电热法,一步制备出新型的钛基Ni-Sn/Ti电极(Ni8Sn/Ti, Ni7Sn3/Ti 和 Ni/Ti)。扫描电镜（SEM）图像表明,催化剂以片状的纳米颗粒形式沉积于钛基体上。利用电化学伏安技术、电位阶跃法和电化学交流阻抗谱（EIS）,研究了这些电极在1mol.L�1NaOH溶液中对甲醇氧化反应的电催化活性。研究表明,与Ni7Sn3/Ti,Ni/Ti以及多晶镍电极相比,Ni8Sn/Ti电极对甲醇氧化反应表现出更高的阳极氧化电流和更低的起始电位。EIS分析表明,在本文所考察的阳极电位和甲醇浓度下,Ni8Sn/Ti电极对甲醇氧化反应显示出极低的电荷传递电阻。结果表明,这种新型的钛基Ni8Sn/Ti电极对甲醇氧化反应具有极高的电催化活性。     

电极/反相微乳液体系电沉积制备纳米金镀层

将含有氯化金的强酸性水溶液作为水相与Triton X-100、正己醇、正己烷组成反相微乳液体系, 并以该微乳液构成电极/反相微乳液电极系统, 利用电沉积方法成功地制备出纳米Au镀层. 循环伏安和交流阻抗对反相微乳液体系电沉积过程的研究发现, 微乳液中Au(III)的还原为完全不可逆过程, 其电化学反应的阻抗值约为具有相同表观浓度氯化金水溶液体系的5.5倍. SEM研究结果表明, 利用微乳液体系电沉积获得的金镀层由纳米Au颗粒组成, 直径为50 nm左右. 所制备的纳米Au修饰电极由于具有较大的比表面积, 其电化学性能优于纯Au电极, 该电极在酸性条件下有较好的析氢性能, 在碱性条件对丙三醇有较好的电催化氧化性能.     

纳米铂微粒修饰电极上甲醛电催化氧化的电位振荡和电流振荡

通过阴极还原-阳极氧化法制备了钛基纳米铂微粒修饰电极, 扫描电镜观察发现, 分布于钛基体表面的氧化钛膜三维网状孔道中的纳米铂微粒具有高度分散状态. 采用多种电化学手段在该电极上不仅观察到甲醛在恒电流条件下产生的电位振荡, 而且在循环伏安和恒电位两种条件下均观察到强烈的电流振荡, 这进一步证明高度分散的纳米铂微粒使电极的催化活性大大提高, 促进了甲醛及其毒化中间产物的电催化氧化过程, 从而有利于电极上电化学振荡的产生. 研究结果还表明, 甲醛底物浓度、硫酸介质浓度、恒电位或恒电流大小等多种因素对振荡强度、范围或类型会产生规律性的影响.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶-凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极. X射线衍射(XRD)表明纳米TiO2为锐钛矿型, 扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态, 平均粒径约25 nm. 通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性, 结果表明, 修饰电极对乙二醛的直接电氧化呈现良好的催化活性, 在0.60和1.23 V(vs SCE)出现两个氧化峰, 二者电流密度分别为16 和42 mA·cm-2, 约为纯Pt电极的2倍和1.5倍, 反应过程受浓差扩散控制.     

乙二醛在Ti/纳米TiO2-Pt修饰电极上的电催化氧化

采用溶胶.凝胶和电沉积法制备Ti基纳米TiO2-Pt(Ti/纳米TiO2-Pt)修饰电极.X射线衍射(XRD)表明纳米TiO2为锐钛矿型,扫描电镜(SEM)显示Pt纳米粒子在纳米TiO2多孔膜的表面呈现簇分散状态,平均粒径约25nm.通过循环伏安(CV)和计时电流法研究了Ti/纳米TiO2-Pt修饰电极对乙二醛直接电氧化的电催化活性,结果表明,修饰电极对乙二醛的直接电氧化呈现良好的催化活性,在0.60和1.23 V(vs SCE)出现两个氧化峰,二者电流密度分别为16和42 mA·cm2,约为纯Pt电极的2倍和1.5倍,反应过程受浓差扩散控制.     

超氧化物歧化酶在纳米金/L-半胱氨酸修饰金电极上的电化学行为

通过L-半胱氨酸将纳米金修饰到金电极上,把超氧化物歧化酶(SOD)固定在修饰电极表面,制备了SOD-纳米金/L-半胱氨酸修饰电极。运用交流阻抗法、循环伏安法等方法表征了该电极,发现SOD在该电极上于0.15V和-0.05V左右产生较明显的氧化还原峰,在0.04～0.24V/s扫描速率范围内,其还原峰电流与扫描速速呈线性关系,表明该电极过程受吸附控制。研究了H2O2对SOD-纳米金/L-半胱氨酸修饰电极伏安行为的影响,发现该电极的还原峰电流与H2O2浓度在1.0×10-6～2.0×10-4mol/L范围内呈良好的线性关系,相关系数为-0.996,可用于对H2O2的分析检测。     

基于纳米结构双层类脂膜的雌激素传感器

采用铂盘电极支撑的纳米金修饰的双层类脂膜(Pt/BLM/Au)来固定雌激素受体(ER),制备Pt/BLM/Au/ER用于检测雌激素的传感器.电极不同修饰状态分别用循环伏安法和交流阻抗法进行表征.以交流阻抗法测得电极结合雌激素后阻抗的改变与17β-雌二醇(E2)的浓度在5～150 ng/L范围呈良好线性关系,相关系数r=...     

Au/PAni/GC电极的制备及对甲醛的电催化氧化研究

应用循环伏安、恒电位阶跃等方法研究了在苯胺修饰的玻碳电极（PAni/GC） 表面金颗粒的电化学沉积及不同的制备方法对甲醛氧化电催化活性的影响。研究表 明,在PAni/GC电极表面,金的电沉积在初始阶段遵循扩散控制瞬时成核三维成长 模式。在碱性介质中,电解沉积法制备的电极比循环伏安法制备的电极对甲醛的催 化氧化有更高的催化电流。但是,在循环伏安法制备的电极上甲醛的氧化可以在很 负的电极电位下发生。     

Nanoporous Pt Catalyst Modified by Sn Electrodeposition for Electrochemical Oxidation of Formaldehyde

A nanoporous Pt particles‐modified Ti (nanoPt/Ti) electrode was prepared through a simple hydrothermal method using aqueous H₂PtCl₆ as a precursor and formaldehyde as a reduction agent. The nanoPt/Ti electrode was then modified with limited amounts of tin particles generated by cyclic potential scans in the range of ?0.20 to 0.50 V in a 0.01 mol·L^?1 SnCl₂ solution, to synthesize a Sn‐modified nanoporous Pt catalyst (Sn/nanoPt/Ti). Electroactivity of the nanoPt/Ti and Sn/nanoPt/Ti electrodes towards formaldehyde oxidation in a 0.5 mol·L^?1 H₂SO₄ solution was evaluated by cyclic voltammetry and chronoamperometry. Electrooxidation of formaldehyde on the nanoPt/Ti electrode takes place at a potential of 0.45 V and then presents high anodic current densities due to the large real surface area of the nanoPt/Ti electrode. The formaldehyde oxidation rate is dramatically increased on the Sn/nanoPt/Ti electrode at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the nanoPt/Ti electrode. Chronoamperogramms (CA) of the Sn/nanoPt/Ti electrode display stable and large quasi‐steady state current densities at more negative potential steps. Amperometric data obtained at a potential step of 100 mV show a linear dependence of the current density for formaldehyde oxidation upon formaldehyde concentration in the range of 0.003 to 0.1 mol·L^?1 with a sensitivity of 59.29 mA·cm^?2 (mol·L^?1)^?1. A detection limit of 0.506 mmol·L^?1 formaldehyde was found. The superior electroactivity of the Sn/nanoPt/Ti electrode for formaldehyde oxidation can be illustrated by a so‐called bifunctional mechanism which is involved in the oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

Hydrothermal Synthesis of Titanium‐Supported Nickel Nanoflakes for Electrochemical Oxidation of Glucose

Titanium‐supported nanoscale flaky nickel electrode (nanoNi/Ti) was prepared by a hydrothermal process using hydrazine hydrate as a reduction agent. Its electrocatalytic activity as an electrocatalyst for the electrooxidation of glucose was evaluated in alkaline solutions using cyclic voltammetry (CV), chronoamperometric responses (CA) and electrochemical impedance spectra (EIS). The nanoNi/Ti electrode exhibits significantly high current density of glucose oxidation. A high catalytic rate constant of 1.67×10⁶ cm³ mol^?1 s^?1 was calculated from amperometric responses on the nanoNi/Ti electrode. Low charge transfer resistances on the nanoNi/Ti in 0.5 M NaOH containing various concentrations of glucose were obtained according to the analysis for EIS. Furthermore, amperometric data show a linear dependence of the current density for glucose oxidation upon glucose concentration in the range of 0.05–0.6 mM with a sensitivity of 7.32 mA cm^?2 mM^?1. A detection limit of 0.0012 mM (1.2 μM) M glucose was found. Results show that the prepared nanoNi/Ti electrode presents high electrocatalytic activity for glucose oxidation.     

Gold particles supported on self-organized nanotubular TiO2 matrix as highly active catalysts for electrochemical oxidation of glucose

Au/TiO₂/Ti electrode was prepared by a two-step process of anodic oxidation of titanium followed by cathodic electrodeposition of gold on resulted TiO₂. The morphology and surface analysis of Au/TiO₂/Ti electrodes was investigated using scanning electron microscopy and EDAX, respectively. The results indicated that gold particles were homogeneously deposited on the surface of TiO₂ nanotubes. The nanotubular TiO₂ layers consist of individual tubes of about 60–90 nm in diameter, and the electrode surface was covered by gold particles with a diameter of about 100–200 nm which are distributed evenly on the titanium dioxide nanotubes. This nanotubular TiO₂ support provides a high surface area and therefore enhances the electrocatalytic activity of Au/TiO₂/Ti electrode. The electrocatalytic behavior of Au/TiO₂/Ti electrodes in the glucose electro-oxidation was studied by cyclic voltammetry. The results showed that Au/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the glucose oxidation than that of gold electrode.     

IrO2电极在含有机小分子水溶液中的电化学活性

通过循环伏安（CV）与电化学阻抗谱（EIS）测试研究了Ti基IrO2系活性涂层电极在含甲醇、甲酸及甲醛三种有机小分子的Na2SO4溶液中的电化学活性,其中以电极/溶液界面的双电层电容来表征电极的活性.结果表明,与同浓度H2SO4溶液相比,该电极在Na2SO4溶液中的电化学活性发生明显下降.有机小分子的加入降低了电极的活性表面积.发现有机物能在较宽的电位范围内发生氧化反应,但在该种电极上的电氧化速率较慢.然而,伴随着析氧反应的发生,有机物的氧化也随之加快.     

树枝状纳米银颗粒的制备与电活性

在Ag(NH3)2+溶液中,在钛基体上电沉积出树枝状纳米银颗粒,研究了沉积电位对树枝状纳米银颗粒形成的影响,探讨了这种树枝状纳米银颗粒形成的机理,并研究了这种钛基树枝状纳米银电极(Ag/Ti)在碱性溶液中对甲醛氧化的电催化活性。结果表明,在30 mmol/LAg(NH3)2+以及沉积电位在-1.8～-1.2 V(vsAg)时,形成了形态为树枝状的纳米银颗粒。在沉积电位为-1.6 V(vs Ag),Ag(NH3)2+浓度为30 mmol/L的溶液中,电沉积制备的这种树枝状纳米银电极(Ag/Ti)对甲醛氧化具有强的电催化活性。循环伏安曲线表明,在0.1 mol/LNaOH溶液中以及甲醛的浓度范围在0～40 mmol/L,甲醛浓度和它的氧化峰电流密度呈现良好的线性关系,检测下限达到0.662 mmol/L,这种新型的树枝状纳米银电极有望作为甲醛检测的传感器。     

A novel titanium-supported nickel electrocatalyst for cyclohexanol oxidation in alkaline solutions

A novel titanium-supported nickel electrode (Ni/Ti) is fabricated by a simple hydrothermal process using hydrazine hydrate as a reduction agent. Its electrocatalytic activity towards cyclohexanol oxidation has been investigated by cyclic voltammetry (CV), chronoamperometry (CA), quasi-steady state polarization and electrochemical impedance spectroscopy (EIS). Effects of various parameters such as potential scan rate and cyclohexanol concentration on the electro-oxidation of cyclohexanol are investigated. Results show that the Ni/Ti electrode behaves as an efficient catalyst for the electro-oxidation of cyclohexanol in basic media and its electrocatalytic activity towards cyclohexanol oxidation is higher than a nickel oxyhydroxide modified nickel electrode (NOMN). It is confirmed that during the anodic potential sweep the electro-oxidation of cyclohexanol follows the formation of NiOOH on the electrode surface and is then catalysed by NiOOH. The rate-determining step for cyclohexanol oxidation is the reaction between the high oxidation state nickel (Ni³⁺) and the adsorbed cyclohexanol on the surface of the Ni/Ti.     

Electrocatalytic activity of a novel titanium-supported nanoporous gold catalyst for glucose oxidation

A novel Ti-supported gold catalyst (nanoAu/Ti) with a nanoporous 3D texture has been fabricated using a hydrothermal method. Au particles were stably deposited on the Ti surface from the mixture of aqueous tetrachlororoauric acid and polyethylene glycol at 180 °C. Voltammetry (CV) and chronoamperometry were used to characterize the nanoAu/Ti electrode and assess its electroactivity towards glucose oxidation. Compared to polycrystalline Au, the nanoAu/Ti electrode shows similar CV profiles in alkaline solution. However, in an alkaline solution containing 10 mM glucose, the nanoAu/Ti electrode presents much higher anodic current densities and a more negative onset potential (ca. ?0.75 V) for glucose oxidation than a bulk Au electrode. Analysis for Tafel plot of the nanoAu/Ti electrode shows that electro-oxidation of glucose takes place via a one-electron rate-determining step. Results indicate a high and (relatively) stable electrocatalytic activity of the nanoAu/Ti for glucose oxidation.     

丙醇和丁醇异构体在钯镍电极上的电催化氧化

β环糊精(β-CD)具有特殊的空腔结构,将β-CD修饰的多壁碳纳米管(MWCNT)涂在钛基底上,采用电沉积的方法在修饰的钛基底上沉积纳米PdNi催化剂。SEM结果表明,PdNi纳米颗粒在β-CD/MWCNT修饰的钛片上有较好的分散度,粒径为90~130 nm。在碱性溶液中,测试了PdNi-β-CD/MWCNT/Ti电极分别对丙醇和丁醇不同异构体氧化的电催化活性;通过计算与-OH相连的碳原子上的Muliken净电荷,分析不同异构体的氧化机理。结果表明,不同异构体的氧化活性不同,PdNi-β-CD/MWCNT/Ti电极对正丙醇和正丁醇的氧化活性明显高于其异构体,-OH所在碳原子上的Muliken 净电荷越小,醇类分子越容易被氧化。