Pt-Se纳米空球修饰玻碳电极上甲酸的电催化氧化

以无定形硒溶胶为模板制备了不同硒覆盖度(θSe)(θSe=0.49,0.39,0.06,0)的Pt-Se和Pt纳米空球(分别记为(Pt-Se)HN和PtHN),发展了利用亚硫酸盐彻底除去核壳纳米粒子上Se的方法.对获得的纳米空球进行了形貌和结构的表征,结果表明所制备的(Pt-Se)HN粒径均匀,分散性好,球壳呈多孔结构.以其作为电催化剂制备了(Pt-Se)HN修饰的玻碳(GC)电极((Pt-Se)HN/GC),利用常规电化学方法比较该电极与PtHN/GC和商用碳载铂(Pt/C)修饰GC(Pt/C/GC)电极对甲酸的催化氧化作用,发现对甲酸氧化的活性顺序为(Pt-Se)HN/GCPtHN/GCPt/C/GC.三种电极催化甲酸氧化的机理有所不同:前者更倾向于通过弱吸附中间体直接氧化成CO2的单途径机理进行,后两者则通过强吸附和弱吸附中间体的双途径机理进行.在一定Se覆盖度条件下,(Pt-Se)HN/GC对甲酸的氧化有助催化作用.     

光催化还原制备Au/Ag核壳结构纳米粒子及其修饰电极的电催化性能

以Keggin结构硅钨杂多酸H4SiW12O40(SiW12)为光催化还原剂,通过光化学还原法制备Au/Ag核壳结构纳米粒子. 透射电子显微镜分析显示,所得纳米粒子粒径为30～40 nm,呈均匀分散的球形颗粒,该制备方法的特点是可以较好的避免单金属纳米粒子的形成. 将Au/Ag核壳纳米粒子修饰到具有PVP膜的玻碳电极表面,得到SiW12-(Au/Ag)-PVP多层膜修饰电极. 该修饰电极在0.5 mol/L H2SO4介质中具有良好的电化学响应,在0～-0.75 V电位范围内,出现了3对归属于SiW12的氧化还原峰,且电极性能稳定,灵敏度高. 对H2O2的电催化还原性能明显优于单金属Ag纳米粒子修饰电极,说明Au核的存在可以很好的改善Ag的电催化性能,Au和Ag之间存在相互协同催化作用.     

以Ag为模板制备Pt纳米空球及其对甲醇氧化的电催化性能

以硝酸银为前驱体,聚乙烯吡咯烷酮(PVP)为表面活性剂,抗坏血酸(AA)为还原剂,在18℃下通过调节氢氧化钠的加入量合成了2种不同粒径的银溶胶;以银溶胶为模板,在室温下合成了不同粒径的铂包银(Ag@Pt)实心纳米粒子;用浓氨水除去Ag核得到球壳上含残留银的铂纳米空球[(Pt-Ag)hollow]及其修饰玻碳(GC)电极[(Pt-Ag)hollow/GC];再用电化学法除去(Pt-Ag)hollow/GC电极上的残留银后,制得铂纳米空球(Pthollow)修饰的GC电极(Pthollow/GC).采用扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、能量色散谱仪(EDS)和X射线衍射仪(XRD)等表征了Pthollow的形貌、组成和结构;以甲醇为探针分子,研究比较了Pthollow/GC和实心铂纳米粒子(Ptnano)修饰GC电极(Ptnano/GC)对甲醇氧化的电催化活性.结果表明,Pthollow分散性好,粒径比较均匀;球壳多孔,具有粗糙的内外表面,比表面积大,是由铂原子和多维多级的铂原子团簇构建的结晶度不高的多晶铂;Pthollow/GC对甲醇的电催化氧化活性明显优于Ptnano/GC电极,且大大降低了贵金属Pt的用量.     

新型纳米铂修饰玻碳电极的制备及电催化性能研究

研究了一种新型纳米铂修饰玻碳电极的制备方法,并对其电化学催化性能进行了研究。实验结果表明,通过电沉积前在金刚石粉末悬浊液中对玻碳电极进行超声处理,可制备出新型玻碳电极。经超声处理后,金刚石颗粒在玻碳电极基体上产生了数微米长的划痕。电沉积过程中,在该电极上可沉积分布较密集的平均尺寸为110nm的Pt颗粒。这种新型纳米铂修饰玻碳电极的表面电化学活性值为0.397 m2/g,高于普通铂修饰玻碳电极,且在0.5 mol/L H2SO4溶液中具有良好的电化学稳定性。     

铁铂核壳纳米粒子修饰玻碳电极制备及对亚硝酸盐还原的电催化性能

通过循环伏安法（CV）在玻碳（GC）电极表面电沉积出分布较为均匀的纳米Fe粒子,制得纳米Fe粒子修饰的GC（纳米Fe/GC）电极,再经“电荷置换”制得具有Fe核Pt壳结构的纳米粒子修饰的（纳米PtFe/GC）电极。 SEM结果显示,纳米Fe/GC和纳米PtFe/GC表面粒子的形貌均呈立方体形,分布较为均匀,粒径在60 nm左右。 纳米PtFe/GC电极对亚硝酸盐的还原具有很高的电催化活性。 3种电极的电催化活性顺序依次为：纳米Fe/GC＜纳米Pt/GC＜纳米PtFe/GC。 相对于纳米Pt/GC电极,纳米PtFe/GC电极的起始还原电位（Ei）正移了0.14 V,还原峰电流（ip）增大了3倍。     

Br?nsted酸性离子液体活化电极催化制氢性能研究

分别采用玻碳( GC)、铂( Pt)和金( Au)电极研究了在Br?nsted酸性离子液体[ HMIm] HSO4中电解水制氢的催化活性,活性大小为Pt > Au >> GC。水中离子液体的含量对析氢电流影响很大,当[ HMIm] HSO4含量为30%(V/V)时,Pt电极催化电解水产氢的阈值电位高达-0.3 V (Ag丝为准参比电极, Ag QRE),在-0.5 V (Ag QRE)处电流密度高达110.52 mA/cm2,为相同条件下Au电极的15倍,GC电极的650倍。计算结果表明,Pt电极在该电解液中的反应活化能为5.68 kJ/mol。电极的高催化活性与[ HMIm] HSO4电离产生的质子有关,使水以H3 O+的形式捕集电子,效率更高。     

SnO2-TiO2薄膜载体对Au-Pt纳米颗粒电化学性能的影响

采用真空镀膜法在玻碳(GC)电极表面修饰SnO2-TiO2薄膜, 在SnO2-TiO2/GC复合电极表面组装Au-Pt双金属纳米颗粒, 制得Au-Pt/SnO2-TiO2/GC复合电极. 通过循环伏安法(CV)研究了SnO2-TiO2薄膜载体对Au-Pt双金属纳米颗粒电化学性能的影响; 采用扫描电镜(SEM)及X射线光电子能谱(XPS)对Au-Pt在SnO2-TiO2薄膜沉积的形貌及结构进行了表征. 研究结果表明, 10 nm的Au-Pt双金属纳米颗粒均匀地组装于SnO2-TiO2薄膜表面; SnO2-TiO2薄膜载体改善了复合电极抗CO中毒能力; Au-Pt双金属合金的形成提高了Pt 对甲醇氧化的电催化能力, SnO2-TiO2薄膜载体又使Pt纳米粒子d空轨道增多, 提高了Au-Pt双金属纳米颗粒的稳定性和催化性能.     

不同介质对Pt/GC电极制备及其性能的影响

应用循环伏安法(CV),扫描电子显微镜(SEM)和电化学原位红外反射光谱(in situFTIRS)研究了不同介质对碳载铂纳米薄膜电极(Pt/GC)的表面结构以及该薄膜电极对甲酸电催化氧化性能的影响.结果表明,使用不同介质的镀铂溶液,均可电沉积出分布较为均匀的Pt粒子,但其尺寸与形貌却相差很大.当以H2SO4作介质,由循环伏安法于玻碳电极上电沉积Pt得到的(Pt/GC1)电极,其Pt粒子粒径约100~200 nm;而在HClO4介质得到的(Pt/GC2)电极,则含有两种Pt微晶:其一是立方体形,粒径约200 nm,其二为菜花状,粒径约400 nm.电化学循环伏安和原位红外反射光谱测试指明,不同介质制备的Pt/GC电极对甲酸的电催化氧化均表现出与本体铂电极(Pt)相类似的特性,即可通过活性中间体或毒性中间体将甲酸氧化至CO2,但不同结构的Pt/GC电极具有不同的电催化活性.进一步以Sb或Pb修饰Pt/GC电极,不仅可以有效地抑制毒性中间体CO的生成,而且还能显著提高其电催化活性.比较本文研究的7种电极,其电催化活性顺序依次为:Sb-Pt/GC2>Pb-Pt/GC2>Pb-Pt/GC1>Sb-Pt/GC1>Pt/GC2>Pt/GC1>Pt.     

肌红蛋白-纳米氧化铝模板-金胶复合组装体的直接电化学与电催化

将肌红蛋白(Mb)固定在纳米氧化铝(AAO)模板-金胶复合组装体修饰玻碳电极表面,制得Mb/AAO/Au colloid/GC薄膜电极.在pH=5.4的HAc-NaAc缓冲溶液中,该薄膜电极于-0.21 V(vs.Ag/AgC l)处有一对准可逆的氧化还原峰,为Mb血红素辅基Fe(Ⅲ)/Fe(Ⅱ)电对的特征峰.在AAO/Au colloid薄膜的微环境中,Mb与玻碳电极间的电子传递明显加快,该Mb/AAO/Au colloid/GC薄膜电极还可用于过氧化氢和溶解氧的催化还原.     

碳纳米管负载纳米铂修饰电极及电催化氧化H2O2的研究

采用化学气相沉积法在碳纳米管(CNT)上负载Pt纳米颗粒,并制备了CNT-Pt修饰玻碳电极(CNT-Pt/GCE).研究了该修饰电极在磷酸缓冲液中对H2O2的电催化氧化作用以及实验条件的影响.计算了H2O2在CNT-Pt/GCE上的电极反应速率常数.结果表明,CNT-Pt/GCE对H2O2的电化学氧化具有良好的催化作用,电极反应速率常数比铂电极高约2.65倍.初步探讨了电催化氧化机理,为酶电化学传感器的研制提供了一条新的途径.     

Preparation of carbon-supported core-shell Au-Pt nanoparticles for methanol oxidation reaction: The promotional effect of the Au core

Core-shell Au-Pt nanoparticles with intimate contact of Pt and Au were prepared by a displacement reaction without formation of monometallic Au nanoparticles. The Au-Pt nanoparticles were dispersed on carbon (Au@Pt/C) and were used to catalyze methanol electrooxidation in acidic solutions at room temperature. The core-shell nanostructure was confirmed by transmission electron microscopy and X-ray photoelectron spectroscopy, and specific catalytic activities were evaluated by CO anodic stripping voltammetry in 0.5 M H(2)SO(4) and by cyclic voltammetry in 1 M CH(3)OH + 0.5 M H(2)SO(4). The Au@Pt/C catalyst demonstrated enhanced specific activity in methanol electrooxidation and showed multiple CO stripping peaks which were all negatively shifted with respect to a similarly prepared Ag@Pt/C catalyst. The activity enhancement is attributed to the presence of Au underneath a very thin Pt shell where electron exchange between Au and Pt had promoted the formation of active oxygen species on Pt, which facilitated the removal of inhibiting CO-like reaction intermediates.     

Characterization of Pt nanoparticles deposited onto carbon nanotubes grown on carbon paper and evaluation of this electrode for the reduction of oxygen

Multiwalled carbon nanotubes (MWCNTs) were grown on the fibers of a commercial porous carbon paper used as carbon-collecting electrodes in fuel cells. The tubes were then covered with Pt nanoparticles in order to test these gas diffusion electrodes (GDEs) for oxygen reduction in H2SO4 solution and in H2/O2 fuel cells. The Pt nanoparticles were characterized by cyclic voltammetry, transmission electron microscopy, and X-ray photoelectron spectroscopy. The majority of the Pt particles are 3 nm in size with a mean size of 4.1 nm. They have an electrochemically active surface area of 60 m2/g Pt for Pt loadings of 0.1-0.45 mg Pt/cm2. Although the electroactive Pt surface area is larger for commercial electrodes of similar loadings, Pt/MWCNT electrodes largely outperform the commercial electrode for the oxygen reduction reaction in GDE experiments using H2SO4 at pH 1. On the other hand, when the same electrodes are used as the cathode in a H2/O2 fuel cell, they perform only slightly better than the commercial electrodes in the potential range going from approximately 0.9 to approximately 0.7 V and have a lower performance at lower voltages.     

Au@Pt纳米粒子单层膜对甲醇氧化的电催化性能及SERS研究

通过种子生长法合成Au@Pt核壳结构纳米粒子,采用两相成膜法制备单层粒子膜,并转移获得Au@Pt核壳纳米粒子单层膜电极,该电极表面纳米粒子分布均匀,具有较大的比表面,对甲醇的氧化具有较好的电催化活性.研究表明,利用内核Au的长程电磁场增强效应,该单层膜表现出均匀且优良的表面增强拉曼散射(SERS)活性,适合作为基底在分子水平上研究表面的吸附和反应.获得了Au@Pt核壳纳米粒子单层膜表面甲醇电催化氧化过程的SERS光谱,为深入分析表面反应机理提供了实验依据.     

石墨烯量子点负载银纳米粒子制备及氧还原电催化活性

银基氧还原电催化剂具有较高的电催化活性且价格相对低廉,因而受到广泛关注. 本文采用简单、预先合成的石墨烯量子点作为载体和还原剂,制得了负载于石墨烯量子点、且无保护剂和表面活性剂的表面洁净银纳米粒子（Ag NPs/GQDs）. 电化学研究表明,Ag NPs/GQDs复合电催化剂的氧还原有较高的电催化活性,氧在碱性溶液中可经4电子途径还原为水. 与商业铂碳电极（Pt/C）相比,AgNPs/GQDs电极具有高催化电流密度、良好稳定性和极佳抗甲醇性能. 该银纳米粒子对开发高性能和低成本的非铂氧还原电催化剂有潜在的应用前景.     

In situ synthesis of Pt/carbon nanofiber nanocomposites with enhanced electrocatalytic activity toward methanol oxidation

Pt/carbon nanofiber (Pt/CNF) nanocomposites were facilely synthesized by the reduction of hexachloroplatinic acid (H(2)PtCl(6)) using formic acid (HCOOH) in aqueous solution containing electrospun carbon nanofibers at room temperature. The obtained Pt/CNF nanocomposites were characterized by TEM and EDX. The Pt nanoparticles could in situ grow on the surface of CNFs with small particle size, high loading density, and uniform dispersion by adjusting the concentration of H(2)PtCl(6) precursor. The electrocatalytic activities of the Pt/CNF nanocomposites were also studied. These Pt/CNF nanocomposites exhibited higher electrocatalytic activity toward methanol oxidation reaction compared with commercial E-TEK Pt/C catalyst. The results presented may offer a new approach to facilely synthesize direct methanol fuel cells (DMFCs) catalyst with enhanced electrocatalytic activity and low cost.     

Pt dendrimer nanocomposites for oxygen reduction reaction in direct methanol fuel cells

Dendrimer-encapsulated Pt nanoparticles (G4OHPt) were prepared by chemical reduction at room temperature. The G4OHPt, with average diameters of ca. 2.7 nm, were characterized by X-ray diffraction, scanning electron microscopy, and thermogravimetric analysis. Electrocatalytic behavior for oxygen reduction reaction was investigated using a rotating disk electrode configuration in an acidic medium, with and without the presence of methanol (0.01, 0.1, and 1 M). Kinetic studies showed that electrodes based on Pt nanoparticles encapsulated inside the dendrimer display a higher selectivity for ORR in the presence of methanol than electrodes based on commercial Pt black catalysts. Also, the dendritic polymer confers a protective effect on the Pt in the presence of methanol, which allows its use as a cathode in a direct methanol fuel cell operating at different temperatures. Good performance was obtained at 90 °C and 2 bar of pressure with a low platinum loading on the electrode surface.     

高分散直接甲醇燃料电池Pt／C阴极电催化剂的制备过程机理与表征

 通过调变的多元醇法制备了40％Pt／C直接甲醇燃料电池阴极电催化剂，应用透射电镜（TEM）及X射线衍射（XRD）方法表征催化剂．结果表明，由该制备方法可得到高分散，金属粒子粒径分布窄的高载量贵金属催化剂．TEM统计结果表明，调变多元醇法制备的40％Pt／C催化剂的金属粒子平均粒径约为2．9nm．直接甲醇燃料电池单池性能测试表明，该方法制得的40％Pt／C的电催化氧还原能力比同型商品催化剂更好．另外，利用UV－Vis光谱研究了催化剂的制备过程．结果表明，在调变的多元醇法中，Pt4＋的还原是一步完成的．     

Electrocatalytic properties of Au@Pt nanoparticles: effects of Pt shell packing density and Au core size

A detailed study of electrocatalytic properties of Au@Pt nanoparticles (NPs) as functions of Pt shell packing density and Au core size in terms of CO/methanol oxidation and oxygen reduction reactions is reported here. While most samples studied showed inferior catalytic activities to those of the commercial Pt black that fall reasonably well in a d-band-center up-shift (i.e., stronger surface bonding) regime, the steepest activity recovery trend as manifested by the smallest Au-core samples suggests a plausible transition to a d-band-center down-shift (i.e., weaker surface bonding) regime as the Au core becomes smaller.     

高载量PtNi金属间化合物的氧还原电催化性能

采用改进的多元醇法制备了PtNi(原子比1∶1)质量分数为60%的高金属载量碳载PtNi合金(PtNi/C), 通过在450 ℃下退火处理获得了碳载PtNi金属间化合物氧还原电催化剂. 该催化剂对氧还原的质量比活性和面积比活性分别是商业化Pt/C(JM Pt/C)催化剂的1.66和2.3倍; 并且加速耐久性测试后PtNi金属间化合物催化剂的质量比活性仍与Pt/C的初始性能相当, 耐久性得到了大幅提升. PtNi/C金属间化合物催化剂氧还原活性和稳定性的提高归因于PtNi的有序原子排布结构及催化剂表面零价金属含量的提高.     

Electroreduction of Oxygen and Electrooxidation of Methanol at Carbon and Single Wall Carbon Nanotube Supported Platinum Electrodes

The present research aimed at investigating the electrocatalytic properties and the electrochemical deposition of Pt nanoparticles on carbon powder, carbon nanotube and preparation of carbon and single wall carbon nanotube supported platinum electrodes. The Pt nanoparticles were synthesized by electroreduction of hexachloroplatinic acid in aqueous solution at ?200 mV. Electrocatalytic properties of the modified electrodes for oxygen reduction were investigated by cyclic voltammetry in O₂ saturated solution containing 0.1 M HClO₄. Methanol electrooxidation at the modified surfaces in 0.5 M HCLO₄ was studied by cyclic voltammetry. The corresponding results showed that the Pt/SWCNT/GC electrode exhibits more improved catalytical activity than the Pt/C/GC electrode.