纳米尺度TiO2／聚吡咯多孔膜电极光电化学研究

用光电流作用谱，光电流－电势图和ＵＶ－Ｖｉｓ光说研究了ＴｉＯ２／聚吡咯多孔膜电极在不含氧化还原对和含不同氧化还原体系电解质溶液中的光电转换过程。ＴｉＯ２／聚吡咯多孔膜电极双层ｎ型半导体结构，内层ＴｉＯ２多孔膜的禁带宽度为３．２６ｅＶ，外层聚吡咯膜的禁带宽度为２．２ｅＶ。     

纳米尺度TiO2聚苯胺多孔膜电极光电化学研究

用光电流作用谱，光电流－电势图等光电化学方法研究了ＴｉＯ２／聚本胺复合多孔膜电极在不含氧化还原和含有没氧化还原对体系中的光电转换过程。结果说明，ＴｉＯ２／聚苯胺复合多孔膜电极为双层ｍ－型半导体结构，ＴｉＯ２多孔膜的禁带宽度为３．２ｅＶ，外层聚苯胺膜的禁带宽度为２．８８ｅＶ。     

电沉积烧结ZrO_2－8 wt％Y_2O_3薄膜及其对AISI 304不锈钢高

在水溶液中于ＡＩＳＩ３０４不锈钢表面电沉积ｚｒ（ＯＨ）＿４－Ｙ（ＯＨ）＿３薄膜，然后在３０Ｄ～５００℃烧结形成ＺｒＯ＿２－８ｗｔ％Ｙ＿２Ｏ＿３薄膜，讨论了相应的机理。研究结果表明，表面沉积ＺｒＯ－８ｗｔ％Ｙ＿２Ｏ＿３薄膜的试样与空白试样相比，氧化增重下降约３倍，表面沉积ＺｒＯ＿２－８ｗｔ％Ｙ＿２Ｏ＿３薄膜的有益作用在于改善了氧化膜与不锈钢基体的附着力和促进铬的选择性氧化。     

Fe_2O_3／ZrO_2催化剂上一氧化碳加氢反应制低碳烯烃 Ⅱ．预处理条件对催化剂结构及性能的影响

用ＴＰＲ，Ｍｏｓｓｂａｕｅｒ谱法，ＸＰＳ，ＸＲＤ及反应评价等手段研究了Ｆｅ２Ｏ３／ＺｒＯ２催化剂的还原行为、铁物种状态和ＣＯ加氢反应性能．结果表明，预处理条件明显影响Ｆｅ２Ｏ３／ＺｒＯ２催化剂表面铁原子的数量、铁锆间的相互作用、催化剂的物相变化以及ＣＯ加氢反应的催化性能．以Ｆｅ２Ｏ３／ＺｒＯ２经氢氟混合气程序升温至７５３Ｋ还原生成的Ｆｅ－Ｚｒ－Ｏ物种为前身，在合成气中进一步还原得到的铁锆催化剂，具有较好的Ｆ－Ｔ反应合成低碳烯烃的选择性．     

丙烷在负载型V2O5/Zr3(PO4)4催化剂上的氧化脱氢

制备了无定型的磷酸锆Ｚｒ３（ＰＯ４）４载体,采用浸渍法在载体上负载０６％～６０％的Ｖ２Ｏ５．所制备的催化剂在丙烷氧化脱氢反应中具有较好的催化性能,如３０％Ｖ２Ｏ５／Ｚｒ３（ＰＯ４）４催化剂在丙烷转化率为１７０％时,丙烯选择性可达５３８％,丙烯收率达９１％．考察了不同反应条件下催化剂的性能．ＸＲＤ、ＩＲ和Ｒａｍａｎ光谱表明,Ｖ２Ｏ５在Ｚｒ３（ＰＯ４）４载体上主要是以高度分散的钒氧物种存在;ＥＳＲ分析结果证明催化剂中存在Ｖ４＋物种,表明Ｖ５＋／Ｖ４＋参与了氧化还原反应．     

铂作为不溶性阳极时也存在着溶解的可能

尽管Ｐｔ→Ｐｔ２＋的φ高达１．２０Ｖ，但由于Ｐｔ→Ｐｔ（ＯＨ）２的φ仅为０．１６５Ｖ，Ｐｔ→ＰｔＣｌ２－６的φ亦只有０．７２Ｖ。所以在含氧酸及其可溶性含氧酸盐以及含卤素离子如Ｃｌ－溶液中以Ｐｔ作为不溶性阳极使用时，溶解损失是不可避免的。只有当表面覆有ＰｔＯ、ＰｔＯ２等氧化膜时，Ｐｔ的溶解才能降至可被忽略的地步     

Fe2O3/ZrO2催化剂上一氧化碳加氢反应制低碳烯烃Ⅱ.预处理条件对催化剂结构及性能的影响

用ＴＰＲ，Ｍｏｓｓｂａｕｅｒ谱法，ＸＰＳ，ＳＲＤ及反应评价等手段了Ｆｅ２Ｏ３／ＺｒＯ２催化剂的还原行为，铁物种状态和ＣＯ加氢反应性能，结果表明，预处理条件明显影响Ｆｅ２Ｏ３／ＺｒＯ２催化剂表面铁原子的数量、铁锆间的相互作用，催化剂的物相变化以及Ｃ氢反应的催经性能，以Ｆｅ２Ｏ２／ＺｒＯ２经氢氩混合氯程序升温至７５３Ｋ还原生成的Ｆｅ－Ｚｒ－Ｏ物种为前身，在合成气中进一步还原得到的铁锆催化剂，具有较好的     

SO_4~（2－）／ZrO_2超强酸催化剂的XPS研究

用ＸＰＳ技术对不同焙烧温度、不同Ｈ＿２ＳＯ＿４浓度制得的／ＺｒＯ＿２和不同反应温度下反应后／ＺｒＯ＿２超强酸催化剂的表面元素电子结合能及表面元素的相对含量进行了分析。结果表明，焙烧温度和反应温度对催化剂表面元素Ｚｒ、Ｏ和Ｓ的氧化态没有影响，但Ｚｒ和Ｏ的电子结合能随温度的升高而下降；Ｏ（－２）至少可归结为三种存在形式的氧；可以在催化剂表面富集，且当Ｈ＿２ＳＯ＿４浓度为０．５ｍｏｌ／Ｌ时，表面富集最显著；Ｈ＿２ＳＯ＿４浓度为１ｍｏｌ／Ｌ时，催化剂表面和总体含硫量都较高；太低和太高的Ｈ＿２ＳＯ＿４浓度时，催化剂表面和总体含硫量都很低。当焙烧温度高至８５３Ｋ或反应温度高至６２３Ｋ以后，催化剂表面含硫量迅速下降。此外，还对催化剂表面的Ｂｒｏｎｓｔｅｄ酸中心的存在形式和催化剂的失活进行了探讨。     

硫酸介质中Pb电极氧化物成长过程的研究

采用实时交流阻抗测量与激光扫描微区光电流技术相结合的现场方法,对铅电极在硫酸溶液中ＰｂＯ和ＰｂＯ＿２的生长过程进行了研究．发现电极在ＰｂＯ的形成区中氧化５ｍｉｎ后,电极欧姆阻抗和ｔ￣（１／２）呈一直线关系,这表明ＰｂＯ是均匀分布在电极表面而成长的．激光扫描微区光电流的实验进一步证实了这一结论．实验中还发现ＰｂＯ＿２在ＰｂＯ层中是局部发生与发展的．     

氧化铁超微粒光电化学及光谱电化学研究

用拉曼光谱、光电流、紫外－可见反射谱等技术研究了附着在铂片表面的α－Ｆｅ２Ｏ３微粒。拉曼光谱的蓝移现象说明５０ｎｍ粒径的粒子较块体材料有尺寸量子化效应。随着电极电势的变化，光电流增加时，ＵＶ－ＶＩＳ反射率相对变化量减少；光电流减少，ＵＶ－ＶＩＳ反射率相对变化量则增大，说明电极电势不仅影响溶液氧化－还原对的氧化还原趋势，而且还影响微粒表面的光吸收。     

Hydrothermal Synthesis, Characterization and Catalytic Properties of Nanoporous MoO3/ZrO2 Mixed Oxide

Introduction Theisobutane/butenealkylationintherefiningin dustryforobtainingacleangasolinewithahigh octane valueisveryimportant[1,2].Sulfuricandhydrofluoric acidsareusedascatalystsinthecurrentindustrial processesfortheisobutane/butenealkylation,inwhich ca…     

Photocurrent generation in heterostructured ultrathin films fabricated by layer-by-layer deposition of polyelectrolytes bearing tris(2,2'-bipyridine)ruthenium(II) and ferrocene moieties

The photoelectrochemical properties of single-component and heterostructured layer-by-layer deposited films bearing tris(2,2'-bipyridine)ruthenium(II) (Ru) moieties were investigated by photocurrent measurements in solutions in the presence of sacrificial reagents. The photocurrent increased with an increase in the thickness of the films and then had a maximum at a thickness of 10 nm. This increase demonstrates a light-harvesting effect based on excitation energy migration among the Ru moieties to the film/electrolyte interface. A cathodic photocurrent was observed for a heterostructured film where bilayers bearing ferrocene (Fc) moieties and bilayers bearing Ru moieties were deposited on an indium tin oxide (ITO) substrate in the order (ITO/Fc/Ru). On the other hand, an anodic photocurrent was observed for the reverse order film (ITO/Ru/Fc). These results show that the direction of the photocurrent is determined by the gradient of the redox potentials formed in the heterostructured films. The internal quantum efficiency for the ITO/Ru/Fc film was twice that for the single-component film (ITO/Ru). This enhancement of the quantum efficiency is due to suppression of charge recombination by successive electron transfers in the heterostructured film.     

Capacitance and photocurrent study of electronic properties of anodic oxide films on Nb and Ta. Evaluation of the ionized donor concentration profile in Nb2O5 film

Electronic properties of electrochemically formed oxide films on Nb were studied by photocurrent and differential capacitance measurements in 0.025 M KH₂PO₄+0.025 M Na₂HPO₄ electrolyte, pH 6.9. Oxide films of n-type conductivity were formed galvanostatically for final potentials ranging from 4 to 230 V. Measurements were performed in two potential regions, which correspond to formation of a depleted layer of variable thickness at relatively low potentials, and to complete depletion of oxide films of electronic charge carriers at higher potentials. In the first potential region the behavior of both capacitance and photocurrent, was governed by a build up of a depleted layer of potential dependent thickness. In the second, high potential, region, which extends up to the oxide film formation potential, the photocurrent and capacitance of oxide films in most features followed the trends typical of dielectric films containing defects and traps. The photocurrent and capacitance measurements on presumably dielectric oxide films formed on Ta were staged for comparison. The capacitance–potential measurements performed in the first potential region enabled us to construct the ionized donor concentration profile across the Nb₂O₅ film width. The limitations on the use of the C–E profiling method for electrochemically formed oxide layers are considered.     

Covalently attached self‐assembly of ultrathin films from hydroxy‐containing porphyrin and diazoresin

Ultrathin films from 5,10,15,20‐tetrakis(4‐hydroxyphenyl) porphyrin (HPP) and diazoresin (DR) via a H bonding interaction were fabricated with the self‐assembly technique. Under UV irradiation, the H bonds between the layers will convert to covalent bonds following the decomposition of the diazonium group of DR. The stability of the film against the polar solvent and electrolyte aqueous solution increases a lot because of the formation of the covalent crosslinking structure. Thus, the photoelectric conversion property of DR/HPP film can be measured directly with a normal photoelectric chemical cell with potassium chloride as the electrolyte. The maximum of the anodic photocurrent was measured as 1.7 μ Å for an eight bilayer DR/HPP film deposited on an indium–tin oxide glass electrode. The action spectrum of the photocurrent generation indicated that the HPP contained in the film is responsible for the generation of the observed photocurrent. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3103–3108, 2003     

Photoelectrochemical properties of alternating multilayer films composed of titania nanosheets and Zn porphyrin

Alternating multilayer films composed of titania nanosheets and Zn porphyrins were prepared by use of a previously reported Langmuir-Blodgett film-transfer method in order to fabricate photoelectrochemical devices. Closely packed titania nanosheet monolayers on indium tin oxide (ITO), mica, and quartz surfaces strongly adsorbed cationic [5,10,15,20-tetrakis(1-methylpyridinium-4-yl)porphyrinatozinc]4+ (ZnTMPyP4+) by electrostatic interactions. The alternating deposition process afforded nanometer-scale multilayer films with the following structure: solid surface/(titania nanosheet/ZnTMPyP4+)n (n is the number of layers). The multilayer films were characterized by various physical measurements, including AFM, XRD, and UV-visible spectra. The visible-light irradiation of this multilayer film on an ITO electrode in the presence of triethanolamine as an electron donor yielded an anodic photocurrent. The action spectrum was consistent with the absorption spectrum of ZnTMPyP4+, which indicates that the photoexcitation of ZnTMPyP4+ is responsible for the photocurrent generation. However, the photocurrent density decreased with an increasing number of layers, which indicates that the harvesting of photoexcited electrons vertically through the titania nanosheets in the ITO/(titania nanosheet/ZnTMPyP4+)n structure was not efficient. To overcome this problem, the use of a lateral interlayer connection to all of the titania nanosheets with Ag paste was examined. As a result, a dramatic improvement in the photocurrent density was obtained. Thus, for efficient photocurrent generation with the titania nanosheet-ZnTMPyP4+ composite material, the lateral connection to all of the titania nanosheet layers is effective.     

Energy transfer between chlorophyll derivatives in silica mesostructured films and photocurrent generation

Layered silica/surfactant mesostructured thin films containing chlorophyllous pigments [C13(2)-demethoxycarbonyl-pheophytin b (pyroPheo b) or zinc C13(2)-demethoxycarbonyl-chlorophyll b (Zn-pyroChl b)] have been prepared on an indium tin oxide (ITO) electrode grafted with a chlorophyll derivative possessing a triethoxysilyl group (copper C13(2)-demethoxycarbonyl-chlorophyllide a 3-triethoxysilyl propylamide, Cu-APTES-Chl a) to achieve effective light harvesting and successive photocurrent generation by the mesostructured films. The incorporation of pyroPheo b and Zn-pyroChl b in the mesostructured film resulted in 1.2- and 1.6-fold increases of the photocurrent density, respectively, as compared to the case of an antenna pigment-free film also grafted to a surface-modified ITO electrode. The difference action spectra, between the electrodes with and without the antenna pigments, coincided well with the absorption spectra of the immobilized pigments. Because direct electron injection from the antenna pigments in the mesostructured films to the ITO electrode was scarcely observed, the energy transfer from the antenna pigments to Cu-APTES-Chl a plays an important role for the increase in photocurrent density. The usefulness of the mesostructured films as model systems is discussed in relation to the photosynthetic primary processes of higher plants.     

酞菁锂薄膜的光电流极性研究

利用旋转涂膜法和真空镀膜法制备了以酞菁锂薄膜为工作层的有机光电器件, 结构为氧化铟锡/聚二氧乙基噻吩: 聚对苯乙烯磺酸/酞菁锂/聚偏氟乙稀/铝(ITO/PEDOT: PSS/LiPc/PVDF/Al). 在可见光和近红外脉冲激光照射下, 研究了器件的光电流极性. 在532 nm脉冲激光照射下, 器件的外电路光电流方向从ITO流向铝; 但在1064 nm脉冲激光照射下, 其外电路光电流极性发生反向, 即从铝流向ITO. 酞菁锂薄膜的吸收光谱和X射线衍射谱图显示, 其对可见和近红外光有非常广的吸收, 且为x晶型. 酞菁锂自由基的双极性特性可随入射光波长的变化而改变.     

氮掺杂二氧化钛-氧化镍双层薄膜的光电致色特性

以金属钛为靶材、O2/N2/Ar混合气氛为溅射气体,在导电玻璃(ITO)表面磁控溅射一层薄膜,再经300-500℃退火处理制备了氮掺杂TiO2薄膜.采用X射线衍射(XRD)、X光电子能谱(XPS)、扫描电子显微镜(SEM)和紫外-可见吸收光谱等对薄膜的微观结构、光学特性和光电化学性能等进行了研究.进而采用化学沉积的方法在TiO2-xNx薄膜表面沉积上一层多孔NiO薄膜,研究表明,制备的ITO/TiO2-xNx/NiO双层薄膜具有明显的光电致色特性,400℃退火处理的氮掺杂TiO2薄膜具有最高的光电流响应,经氙灯照射1h后,薄膜从无色变成棕色,500nm波长处光透过率从79.0%下降至12.6%.     

Electrochemical properties of protoporphyrin IX zinc(II) films

The electrochemical properties of protoporphyrin IX zinc(II) (ZnPP) films on indium-tin oxide (ITO) substrate have been studied for three types of films with different arrangements, which were an adsorbed film of ZnPP and LB films of ZnPP and its hybrid with hexadecyltrimethylammonium bromide. Cyclic voltammetry (CV) measurement showed that, as the adsorbed amount of ZnPP increases, an irreversible oxidation peak of ZnPP film is intensified. This reveals that electrochemical properties depend on the adsorbed amount rather than the orientation of porphyrin molecules. It was also supported from CV measurement and ultraviolet-visible absorption spectroscopy that porphyrins adsorbed on ITO substrate were desorbed after the single scan of potential. Additionally, photoresponse of these ZnPP films was investigated by photocurrent measurement. The photocurrent generation is due to carboxylic acid moieties but not ZnPP macrocycles.     

还原石墨/氧化锌复合薄膜的制备及其光电转换性能

本工作研究不同过程还原的氧化石墨rGO/ZnO(reduced graphiteoxide/ZnO)复合膜的可见光激发光电转换性能。氧化石墨(GO)经KOH还原处理或NaBH4还原处理后,和氧化锌溶胶混合,通过旋涂法和热处理在F掺杂SnO2薄膜导电玻璃(FTO)衬底上形成复合薄膜。采用XRD、FTIR、FE-SEM、XPS、UV-Vis等方法对复合薄膜的晶相结构、微观形貌等进行表征,并测试了复合薄膜在可见光照射下的光电转换性能。GO的预处理过程对复合薄膜的结构影响显著,采用NaBH4对GO处理更有利于形成均匀薄膜。光电流测试结果表明不同复合薄膜均能实现可见光照射下产生光电流,其原理为rGO的光激发电子跃迁到ZnO,而空穴在rGO中迁移,在rGO与ZnO界面实现光生载流子分离。其中NaBH4处理后的rGO/ZnO复合薄膜光电流密度最大,达6×10-7A·cm-2。