蛋白质-铍试剂体系的吸收光谱研究及分析应用

试验发现铍试剂与无色的蛋白质能发生染色反应,用吸光光度法研究了铍试剂与牛血清白蛋白反应前后的吸收光谱及其反应机理,蛋白质结合铍试剂的结合数为１７,制作了重要蛋白质的工作曲线,线性范围约为２０～１８０μｇ．ｍｌ＾－１,用于人血清样品测定,结果满意。     

乳化剂OP存在下蛋白质与虎红的超分子显色反应研究及分析应用

在pH 2.36～3.29 的Britton-Robinson缓冲介质中,在乳化剂OP存在条件下,虎红与蛋白质发生超分子显色反应形成红色的超分子复合物,该超分子复合物的最大吸收波长为565 nm,而试剂的最大吸收波长为568 nm,紫移了3 nm.在565 nm处考察了多种蛋白质的响应情况,结果表明测定牛血清白蛋白(BSA)、人血清白蛋白(HSA)及γ-球蛋白(IgG)时具有高灵敏度,它们的表观摩尔吸光系数ε565和桑德尔灵敏度s分别为1.836×106、 2.213×106、 2.932×106 L·mol-1·cm-1,和0.036、 0.031、 0.061 μg/cm,其线性范围分别为2～36、 2～36 和2～40 mg/L.除阴、阳离子表面活性剂外,其余大部分物质不干扰蛋白质的测定.所拟方法应用于新鲜人尿液和人血清中总蛋白的测定,结果与考马斯亮蓝G-250法基本一致.     

血清蛋白-荧光素复合物单扫极谱波与应用

在0．08mol／L的HAc中，荧光素与牛血清白蛋白(BSA)或人血清白蛋白(HSA)相互作用形成复合物。复合物使荧光素在-0．58V(vs．SCE)处的还原峰电流增大，峰电流的增大值与加入的BSA或HSA的浓度在一定的范围内呈线性关系。BSA在2—24μg／mL范围内呈线性关系，检出限为1μg／mL；HSA在2—22μg／mL范围里呈线性关系，检出限为0．8μg／mL。应用该法测定了人血清蛋白样品，结果令人满意。     

微量铍的示波极谱测定

本文介绍了铍与铍试剂Ⅱ络合物的极谱特性.在氢氧化铵介质中,铍与铍试剂Ⅱ生成电活性络合物.1:1的铍/铍试剂Ⅱ络合物在-0.80伏(对饱和甘汞电极)有一灵敏的吸附波.最适宜的支持电解质为4％EDTA-0.8N NH_4 OH-0.5N NH_4Cl-0.002％铍试剂Ⅱ.铍的测定范围为1.5×10(-8)M-1×10(-5)M.研究了干扰情况.     

ICP-AES法测量铍钴铜合金中主量元素铍、钴的含量

建立ICP–AES法测定铍钴铜合金中主量元素铍、钴含量的方法。将试样用硝酸、盐酸溶解,在钇内标存在的情况下以等离子体光源激发,并分别选择分析谱线Be 313.1 nm,Co 228.6 nm进行光谱测定。铍、钴含量在0~5%范围内与光谱强度线性相关,铍、钴两元素线性相关系数分别为0.999 18,0.999 91;检出限分别为0.000 12%,0.001 1%;测定结果的相对标准偏差为0.25%~4.59%;回收率在96%~102%之间。该方法操作简单实用,可同时测定铍、钴两元素,测定结果准确可靠。     

偶氮氯膦-pB与铍的配合反应及其应用

偶氮氯膦-pB在pH9氨-氯化铵缓冲体系中可与铍形成配合物。试剂及其铍配合物均稳定,最大吸收分别位于570nm和615nm;铍配合物的表现摩尔吸光系数为3.15×10~4;铍量在0—10μg/25mL范围符合比尔定律。方法简便而准确。     

荧光法测定铍的研究

研究了新荧光试剂 7 [(2 ,4 二羟基 5 羧基苯 )偶氮 ] 8 羟基喹啉 5 磺酸 (DHCPAQS)与铍络合的反应条件及测定方法。在pH 8.0硼砂体系的缓冲介质中形成R∶Be =2∶1型的强荧光配合物 ,其λex/λem=362nm/ 497nm。铍含量在 0～ 0 .2 0mg·L- 1范围内呈线性关系 ,检出限为 2 .2×10 - 6 mol·L- 1。该方法应用于合金样中痕量铍的测定 ,结果满意。     

桑色素-β-环糊精荧光光度法测定痕量铍的研究——地质样品中痕量铍的测定

本文研究了测定铍的荧光光度法,在β-环糊精(β-CD)存在下桑色素与铍的反应条件,在0.008mol/L NaOH介质中,铍与桑色素形成配合物,其激发波长为420nm,发射波长为517nm,铍的含量在8～40ng/mL范围内与荧光强度呈线性关系。由于β-CD的存在大大提高了方法的选择性,而灵敏度也有所提高,用于痕量铍的测定可得到满意结果。     

鈹的分析化学Ⅰ.借对-磺基苯偶氮变色酸(SPADNS)比色测定鈹

許多偶氮染料能与铍在适宜的pH范围內生成有色化合物。如铍试剂Ⅱ,钍试剂,鈾试剂Ⅰ以及偶氮膦等已用于微量铍的测定。虽然对-磺基苯偶氮变色酸(SPADNS)在钍和锆的分光光度分析和螯合滴定中已有应用;并且等曾指出在碱性溶液中     

电感耦合等离子体原子发射光谱(ICP-AES)法测定铝铍中间合金中的铍

通过对铍的自吸效应和光谱干扰研究,选取了Be(Ⅱ)313.1nm作为分析线,建立了铝铍合金中测定铍元素含量的电感耦合等离子体原子发射光谱(ICP-AES)法。实验结果表明,谱线Be(Ⅱ)313.0nm的线性范围达到20μg/mL,谱线Be(Ⅱ)3 131nm的线性范围可达30μg/mL,当溶液中铍元素的浓度超过线性范围时,两条谱线的工作曲线发生弯曲,产生明显的自吸效应,样品分析过程中避免使用有自吸效应的谱线,可以大大提高分析结果的准确性;样品中主要杂质元素和基体对铍的谱线不产生光谱干扰。方法中铍的检出限为0.000 4%。铍的质量浓度在1.0~15μg/mL时,工作曲线的线性回归方程为y=265.101 0x+0.45,相关系数R=0.999 645。按实验方法分别对铝铍合金样品和合成的模拟标准样品进行回收率和精密度实验,标准加入回收率在101%~103%,相对标准偏差在0.58%~0.98%。方法能够准确快速地分析铝铍中间合金中铍的含量。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.