Low voltage electron induced cathodoluminescence degradation and surface characterization of Sr3(PO4)2:Tb phosphor

Tb³⁺-doped Sr₃(PO₄)₂ phosphor was prepared by a sol-gel combustion method. A trigonal structure having Sr and O atoms occupying two different lattice sites were obtained. Scanning Auger nanoprobe was used to analyze the morphology of the particles. Photoluminescence (PL) and cathodoluminescence (CL) properties of Sr₃(PO₄)₂:Tb powder phosphors were evaluated and compared. In addition, the CL intensity degradation of Sr₃(PO₄)₂:Tb was evaluated when the powders were irradiated with a beam of electrons in a vacuum chamber maintained at an O₂ pressure of 1 × 10⁻⁶ Torr or a background pressure of 1 × 10⁻⁸ Torr O₂. The surface chemical composition of the degraded powders, analyzed by X-ray photoelectron spectroscopy (XPS), suggests that new compounds (metal oxides) of strontium and phosphorous were formed on the surface. It is most likely that these compounds contributed to the CL intensity degradation of the Sr₃(PO₄)₂:Tb phosphors. The CL properties and possible mechanism by which the new metal oxides were formed on the surface due to a prolonged electron beam irradiation are discussed.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Lattice site dependent cathodoluminescence behavior and surface chemical changes in a Sr5(PO4)3F host

Eu activated Sr₅(PO₄)₃F phosphor powders have been subjected to the electron bombardment at 2 keV (10 μA) at an oxygen pressure of 1×10⁻⁶ Torr. The synthesized Sr₅(PO₄)₃F phosphor was identical to the hexagonal apatite structure, with the Sr present at two different sites C_s (S1) and C₃ (S2) in the Sr₅(PO₄)₃F host, as inferred from the crystallographic study. Cathodoluminescence (CL) and Auger electron spectroscopy of the phosphor excited by the same electron beam were used to monitor changes in the surface state during prolonged electron bombardment. A direct correlation between the surface reactions and the degradation of the CL brightness was observed. Both C and F were depleted from the surface during electron bombardment. The postulated mechanism for the electron stimulated chemical reactions on the phosphor surface is electron beam dissociation of molecular species to atomic species, which subsequently react with C to form volatile compounds CO₂, CH₄, etc. and with Sr₅(PO₄)₃F to form a non luminescence layer of metal oxides of Sr and P.     

Effect of Y2O3 addition on the conductivity and elastic modulus of (CeO2)1 − x(YO1.5)x

The conductivity and elastic modulus of (CeO₂)_1 − x(YO_1.5)_x for x values of 0.10, 0.15, 0.20, 0.30, and 0.40 were investigated by experiments and molecular dynamics simulations. The calculated conductivity exhibited a maximum value at approximately 15 mol% Y₂O₃; this trend agreed with that of the experimental results. In order to clarify the reason for the occurrence of the maximum conductivity, the paths for the transfer of oxygen vacancies were counted. The numerical result revealed that as the content of Y₂O₃ dopant increases, the number of paths for the transfer of oxygen vacancies decreases, whereas the number of oxygen vacancies for conductivity increases. Thus, the trade-off between the increase in the number of vacancy sites and the decrease in the vacancy transfer was considered to be the reason for the maximum conductivity occurring at the Y₂O₃ dopant content of approximately 15 mol%. The calculated elastic modulus also exhibited a minimum value at approximately 20 mol% Y₂O₃, which also agreed with the experimental results. It was shown that the Y–O–Y bonding energy increased with the increasing content of Y₂O₃ dopant. Thus, the trade-off between the increase in the number of vacancy sites and that in the Y–O–Y bonding energy was considered to be the reason for the minimum elastic modulus occurring at the Y₂O₃ dopant content of approximately 20 mol%.     

Magnetotransport and magnetotunneling in single-layer, two-layer, and three-layer Bi2Sr2Can−1CunOz (n=1,2,3) single crystals

In continuous magnetic fields H up to 28 T, we have studied the out-of-plane transport properties and tunneling characteristics of high-quality nondoped single crystals of the Bi-cuprate family: Bi₂Sr₂CuO_6+δ (Bi2201), Bi₂Sr₂CaCu₂O_8+δ (Bi2212) and Bi₂Sr₂Ca₂Cu₃O_10+δ (Bi2223) grown by an identical method. For all compounds the out-of-plane magnetotransport ρ_c(H) is negative in the temperature region where ρ_c(T) shows in the normal state a semiconducting-like temperature dependence. The negative magnetoresistance of ρ_c corresponds to the suppression of the semiconducting temperature dependence of ρ_c(T) which is found to be isotropic. For the Bi2201 compound, where the normal state can be reached in the available magnetic fields (28 T), a nearly complete suppression of the low-temperature upturn in ρ_c(T) is observed in the highest magnetic fields with a tendency towards a metallic behavior down to the lowest temperatures (0.4 K). Using the break-junction technique, especially for the Bi2212 and Bi2232 compounds, a clear superconducting gap structure can be observed. Both for temperatures above the critical temperature and for magnetic fields above the upper critical field, a pseudogap structure remains present in the tunneling spectra. The applied magnetic fields yield a stronger suppression of the superconducting state compared to that of the normal-state gap structures as manifested in ρ_c(T) transport and tunneling.     

Transport properties and defect analysis of La1.9Sr0.1NiO4 + δ

The oxygen flux through La_1.9Sr_0.1NiO_4 + δ has been measured as a function of oxygen activity gradient and temperature (750–1000 °C). The oxygen nonstoichiometry was determined by thermogravimetry in the temperature range of 400–1000 °C and oxygen partial pressures of 0.0002–1 atm. The total conductivity was measured over a similar range of conditions. The oxide ion partial conductivity derived from the oxygen flux data is approximately 4 orders of magnitude lower than the total, mainly p-type electronic conductivity. The defect structure was derived based on the data. Combining the oxygen flux and oxygen nonstoichiometry, the self diffusion coefficient of oxygen interstitials was evaluated.     

Electronic band structure and Fermi surface of new low-temperature Ni-based superconductors: 3.3 K (Ni2P2)(Sr4Sc2O6) and 2.7 K (Ni2As2)(Sr4Sc2O6) from first principles

Based on first-principle FLAPW-GGA calculations, we have investigated structural and electronic properties of the recently synthesized tetragonal (space group P4/nmm) nickel-based pnictide oxide superconductors: 3.3 K (Ni₂P₂)(Sr₄Sc₂O₆) and 2.7 K (Ni₂As₂)(Sr₄Sc₂O₆). Optimized structural data, electronic bands, total and partial densities of states, and Fermi surface topology have been obtained and discussed in comparison with available experiments and with their Fe-based (Fe₂P₂)(Sr₄Sc₂O₆) and (Fe₂As₂)(Sr₄Sc₂O₆) analogs.     

Density functional analysis of the magnetic structures of Sr2MGe2O7 (M=Mn,Co)

To examine the difference between the magnetic structures of Sr₂MGe₂O₇ (M=Mn, Co), we evaluated their spin exchange interactions by performing energy-mapping analysis based on density functional theory calculations. The calculated intra- and inter-layer spin exchanges correctly predict the G-type and C-type antiferromagnetic structures of Sr₂MnGe₂O₇ and Sr₂CoGe₂O₇, respectively, and the Curie–Weiss temperatures estimated from these spin exchanges are also in good agreement with the experiment. The ∥c and ⊥c orientations of the spins in the ordered magnetic structures of Sr₂MnGe₂O₇ and Sr₂CoGe₂O₇, respectively, were also examined by considering spin–orbit coupling.     

Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

三明治结构Tan(B3N3H6)n+1 团簇的磁性和量子输运性质

利用密度泛函理论和非平衡格林函数方法, 本文对小尺寸团簇Ta_n(B₃N₃H₆)_n+1 (n ≤ 4)的磁性和量子输运性质进行了系统的研究. 计算结果表明, 此类体系采用三明治结构作为其基态并且具有较高的稳定性. 体系的磁矩随团簇尺寸的增大而线性增大. 当把Ta_n(B₃N₃H₆)_n+1团簇耦合到Au电极上时, 形成的Au-Ta_n(B₃N₃H₆)_n+1-Au体系在有限偏压下展示出了较强的自旋过滤能力, 因而可以被看做是一类新型的低维自旋过滤器.     

Improving microwave dielectric properties of La2.98/3Sr0.01(Mg0.5Sn0.5)O3 ceramics with CuO additive

The microwave dielectric properties of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were investigated with a view to their application in microwave devices. CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method. The X-ray diffraction patterns of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics exhibited no significant variation of phase with sintering temperature. By adding 0.75 wt.% CuO, a dielectric constant of 20.07, a quality factor (Q × f) of 63,000 GHz, and a temperature coefficient of resonant frequency τ_f (−77.0 ppm/°C) were obtained when La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were sintered at 1500 °C for 4 h.     

Quasi-two-dimensional magnetism in (CnH2n+1NH3)2CuCl4 studied by electron paramagnetic resonance

The quasi-two-dimensional magnetism in the layered transition metal compound (C_nH_2n+1NH₃)₂CuCl₄ (n=10, 14) was investigated by means of electron paramagnetic resonance (EPR) and superconducting quantum interference device measurements. As a result, the high temperature magnetic phase transitions were reflected in the EPR parameters in a sensitive manner.     

Synthesis and luminescence properties of Eu, Ce and Tb-activated Sr3La2(BO3)4 under UV excitation

The spectroscopic properties in UV-excitable range for the phosphors of Sr₃La₂(BO₃)₄:RE³⁺ (RE³⁺=Eu³⁺, Ce³⁺, Tb³⁺) were investigated. The phosphors were synthesized by conventional solid-state reactions. The photoluminescence (PL) spectra and commission international de I'Eclairage (CIE) coordinates of Sr₃La₂(BO₃)₄:RE³⁺ were investigated. The f-d transitions of Eu³⁺, Ce³⁺ and Tb³⁺ in the host lattices are assumed and corroborated. The PL and PL excitation (PLE) spectra indicate that the main emission wavelength of Sr₃La₂(BO₃)₄:Eu³⁺ is 611 nm, and Sr₃La₂(BO₃)₄:Ce³⁺ shows dominating emission peak at 425 nm, while Sr₃La₂(BO₃)₄:Tb³⁺ displays green emission at 487, 542, 582 and 620 nm. These phosphors were prepared by simple solid-state reaction at 1000 °C. There are lower reactive temperature and more convenient than commercial phosphors. The Sr₃La₂(BO₃)₄:Tb³⁺ applied to cold cathode fluorescent lamp was found to emit green light and have a major peak wavelength at around 542 nm. These phosphors may provide a new kind of luminescent materials under ultraviolet excitation.     

Electronic structure and optical properties of Nb-doped Sr2TiO4 by density function theory calculation

This paper investigates the effect of Nb doping on the electronic structure and optical properties of Sr2TiO4 by the first-principles calculation of plane wave ultra-soft pseudo-potential based on density functional theory(DFT).The calculated results reveal that due to the electron doping,the Fermi level shifts into conduction bands(CBs) for Sr2 Nb x Ti1 x O4 with x=0.125 and the system shows n-type degenerate semiconductor features.Sr2TiO4 exhibits optical anisotropy in its main crystal axes,and the c-axis shows the most suitable crystal growth direction for obtaining a wide transparent region.The optical transmittance is higher than 90% in the visible range for Sr2 Nb 0.125Ti0.875O4.     

Facile fabrication of Zn/Zn5(OH)8Cl2·H2O flower-like nanostructure on the surface of Zn coated with poly (N-methyl pyrrole)

Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructures was electrodeposited on the coated Zn with poly (N-methyl pyrrole) in 0.1 M Zn (NO₃)₂ and 0.1 M KCl solution. The morphology and the structure of the Zn/Zn₅(OH)₈Cl₂·H₂O were characterized by Field Emission Scanning Electron Microscopy (FESEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray diffraction analysis (XRD). The FT-IR results showed special peaks at 908 and 728 cm⁻¹ related to Zn₅(OH)₈Cl₂·H₂O. The FESEM results indicated that Zn/Zn₅(OH)₈Cl₂·H₂O consists of a flower-like nanostructure and these flower-shaped structures contain many shaped nanopetals with the thickness of 27.8 nm. The XRD result confirmed that the major phase of electrodeposited product in 0.1 M KCl as supporting electrolyte was Zn₅(OH)₈Cl₂·H₂O. The ability of PMPy to create a thin film and the existence of several pores in its matrix act as a mold for the growth of Zn/Zn₅(OH)₈Cl₂·H₂O flower-like nanostructure. The trapping of Cl⁻ and OH⁻ within pores can be considered as the reason for the formation of flowerlike Zn/Zn₅(OH)₈Cl₂·H₂O nanostructures in 0.1 M KCl.     

The influence of temperature (20-1000 °C) on binary mixtures of solid solutions of CH3COOLi·2H2O-MgHPO4·3H2O

Thermally induced phase transitions (20-1000 °C) in the substrates and binary mixtures of CH₃COOLi·2H₂O(1)-MgHPO₄·3H₂O(11) have been analysed. Changes taking place on dehydration and thermal dissociation of binary mixtures prepared with percent molar ratios of 90-10% were studied by differential thermal analysis (TG, DTG, DTA), IR-spectroscopy and WAXS.The above-mentioned substrates changed their structure when heated for 1 h at 500 or 1000 °C. CH₃COOLi·2H₂O(1) (ID: 23-1171) changed the structure at 500 °C to that of Li₂CO₃ (ID: 22-1141), while at 1000 °C the structure was impossible to analyse as the compound reacted both with porcelain and with platinum (crucible materials). MgHPO₄·3H₂O(11) (Newberyite, ID: 35-780, 19-762) changed its structure at 500 °C to amorphous phase and at 1000 °C to Mg₂P₂O₇ (ID: 32-626).The following compounds were assayed in the respective binary mixtures heated at 500 °C for 1 h: 70% (1)-30%(11): LiMgPO₄ (ID: 18-735), MgO (ID: 4-829); 50%(1)-50%(11): LiMgPO₄ (ID: 18-735), Li₃PO₄ (ID: 25-1030); 30%(1)-70%(11): LiMgPO₄ (ID: 32-574); binary mixtures heated at 1000 °C contained the following compounds: 70%(1)-30%(11): LiMgPO₄ (ID: 32-574,18-735), Li₃PO₄ (ID: 15-760,25-1030), MgO (ID: 4-829); 50%(1)-50%(11): LiMgPO₄ (ID: 32-574, 18-735), MgO (ID: 4-829); 30%(1)-70%(11): LiMgPO₄ (ID: 18-735, 32-574), Mg₂P₂O₇ (ID: 22-1152, 8-38), Li₄SiO₄ (37-1472).     

The effect of Si surface nitridation on the interfacial structure and electrical properties of (La2O3)0.5(SiO2)0.5 high-k gate dielectric films

Thermal stability, interfacial structures and electrical properties of amorphous (La₂O₃)_0.5(SiO₂)_0.5 (LSO) films deposited by using pulsed laser deposition (PLD) on Si (1 0 0) and NH₃ nitrided Si (1 0 0) substrates were comparatively investigated. The LSO films keep the amorphous state up to a high annealing temperature of 900 °C. HRTEM observations and XPS analyses showed that the surface nitridation of silicon wafer using NH₃ can result in the formation of the passivation layer, which effectively suppresses the excessive growth of the interfacial layer between LSO film and silicon wafer after high-temperature annealing process. The Pt/LSO/nitrided Si capacitors annealed at high temperature exhibit smaller CET and EOT, a less flatband voltage shift, a negligible hysteresis loop, a smaller equivalent dielectric charge density, and a much lower gate leakage current density as compared with that of the Pt/LSO/Si capacitors without Si surface nitridation.     

Complex impedance spectroscopic studies of Ba(Pr1/2Ta1/2)O3 ceramic

The polycrystalline sample of Ba(Pr_1/2Ta_1/2)O₃ was prepared by a high-temperature solid-state reaction technique. The crystal symmetry, space group and unit cell dimensions were derived from the experimental results using FullProf software. XRD analysis of the compound indicated the formation of a single-phase tetragonal structure with the space group P4/mmm (1 2 3). Impedance and electric modulus analysis were used as tools to analyze the electrical behavior of the sample as a function of frequency at different temperatures. The impedance analysis of the compound indicated a typical negative temperature coefficient of resistance behavior, and dielectric relaxation was found to be of non-Debye type. The frequency dependent maximum of the imaginary part of the electric modulus follows the Arrhenius law with activation energy of 0.15 eV. The ac conductivity data obeys double power law.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.