密闭微波辅助萃取丹参中有效成分的研究

应用具有压力控制附件的MSP-100D密闭微波萃取装置,对丹参中的有效成分丹参酮、丹参酮A及隐丹参酮进行微波萃取研究.在乙醇体积分数为90%,微波辐射时间为4min,溶剂体积对样品质量比为20∶1和样品粒径为120目的条件下,有效成分提取率最佳.对比了密闭微波萃取同索氏萃取和超声萃取丹参有效成分的差异.     

微波辅助萃取新鲜芦荟叶中芦荟甙的研究

应用密闭微波萃取装置对芦荟中的有效成分芦荟甙进行了微波萃取研究,并利用透射电子显微镜对微波萃取机理进行了初步探讨.讨论了不同萃取剂、溶剂浓度、萃取时间和微波功率等对提取率的影响.在萃取剂为乙醇-水体系,溶剂(乙醇)体积分数为70%、萃取时间为4min及微波功率为340W的条件下,萃取效果最佳.与索氏提取及超声波萃取法相比,本法具有萃取速度快、提取率高及溶剂用量少等特点.     

超声-微波协同萃取装置用于土壤中多环芳烃的分析

本研究将开放式微波和直接超声波振荡两种不同的能量方式相结合,研制出超声-微波协同萃取装置。通过萃取土壤中微量多环芳烃(PAHs),对方法和仪器的可行性进行了初步评价。结果表明,在60 mL二氯甲烷-正已烷(1∶1,V/V)的混合萃取剂,100 W微波辐射功率(超声振动功率固定为50 W),萃取9~10m in,土壤中多环芳烃回收率达86.6%,相对标准偏差约4.0%。与索氏抽提、高压密闭和开放式微波等萃取方法相比,本方法具有样品容量大,萃取时间短,萃取效率受样品中含水量和溶剂极性影响小等优点。     

高效液相色谱法研究当归指纹图谱

目的:研究当归药材的指纹图谱.方法:高效液相色谱法,Hypersil ODS柱(4.6 mm×250 mm,5μm),Kromasil ODS保护柱(4.6 mm×10 mm,5μm).甲醇-1%醋酸梯度流动相,流速1.0 mL/min,柱温25℃.以当归对照药材为对照品,色谱峰光谱采集范围:190~400 nm;以阿魏酸为参照物并测定了阿魏酸的含量,检测波长:323nm,流动相:甲醇-1%醋酸(40∶60,V/V),流速0.7 mL/min.结果:找出了22个共有峰,其中5号峰为阿魏酸,11个样品与当归对照药材之间的相似度均在90%以上,平均相似度为96.77%.结论:样品处理方法简单,研究所得的当归指纹图谱稳定性、重复性好,可以作为当归极性部分的特征性指纹图谱.     

L-半胱氨酸衍生物配体交换手性色谱固定相

应用密闭微波萃取装置对芦荟中的有效成分芦荟甙进行了微波萃取研究,并利用透射电子显微镜对微波萃取机理进行了初步探讨,讨论了不同萃取剂、溶剂浓度、萃取时间和微波功率等对提取率的影响,在萃取剂为乙醇-水体系,溶剂（乙醇）体积分数为70％、萃取时间为4min及微波功率为340W的条件下,萃取效果最佳,与索氏提取及超声波萃取法相比,本法具有萃取速度快、提取率高及溶剂用量少等特点。     

密闭微波辅助萃取天麻中天麻素的研究

应用密闭微波萃取装置,对中药天麻中有效成分天麻素的萃取进行了研究。分别讨论了药材颗粒粒径、提取溶剂浓度、微波提取时间和提取剂的用量对微波萃取天麻素的影响。结果表明:当药材粒径<50μm,乙醇体积分数为50%,微波辐射时间为2min,提取剂质量为药材质量的30倍时,天麻素提取率最高。此外,将微波萃取与索氏萃取和超声波萃取进行了比较。     

超声微波协同萃取/气相色谱法测定土壤中的多溴联苯醚

建立了同时测定土壤中7种多溴联苯醚(PBDEs)的超声微波协同萃取/气相色谱测定方法.考察了萃取溶剂的种类和用量、微波功率、萃取时间等因素对模拟土壤中PBDEs回收率的影响,得到了最佳萃取条件:萃取剂为50 mL正己烷-丙酮(1:1),微波辐射功率为90W,萃取时间为10 min.在最佳条件下,PB-DEs在10～40...     

HPLC法测定浓缩当归丸中阿魏酸的含量

建立了浓缩当归丸中阿魏酸的HPLC测定方法.采用C18色谱柱(TSK-GEL,4.6×150 mm,5μm),以甲醇-水-磷酸(30∶70∶0.3,V/V/V)为流动相,流速1.0 mL/min,检测波长320 nm.结果阿魏酸在0.006~0.15μg范围内线性关系良好,r为0.9999,平均加样回收率为96.91%.本方法可用于浓缩当归丸中阿魏酸的含量监控.     

一种新型微波辅助萃取法用于中药刺五加中总黄酮萃取的研究

微波萃取法是目前世界上公认的绿色样品预处理技术之一 .它在环境、生化、食品、工业以及天然产物和中药等领域均有广泛的应用 [1～ 4 ] .目前 ,最常用的微波萃取系统有两种 [5] ,一种是使用多模式微波炉 ,在密闭容器中加热样品及有机溶剂 ,将目的组分从样品基体中萃取出来 .由于在密闭容器中 ,被萃取样品和溶剂处于高压下 ,温度很高 ,使待萃取物的溶解度增大 ,可获得更高的萃取率 .同时 ,用于这种微波萃取的系统一般可同时容纳 9～ 1 2个萃取罐 ,使试样的批量处理能力大大提高 .该法最主要的缺点是萃取后的液体一般需经离心分离或微孔玻璃…     

超声微波协同萃取-气相色谱法测定土壤中邻苯二甲酸酯类化合物

研究了超声微波协同萃取-气相色谱测定土壤中的邻苯二甲酸酯类化合物。考察了萃取溶剂、微波功率、萃取时间等因素对回收率的影响,得到了最佳萃取条件为:以正己烷/丙酮(1∶1)为萃取剂,溶剂用量为60 mL,微波辐射功率为100 W(超声功率固定为50 W),萃取12 min。该条件下,模拟土样中酞酸酯的平均回收率可达92.5%。方法的检出限为0.05~0.16 mg/kg,相对标准偏差(RSD)5.8%。与直接超声、开放式微波萃取法相比,此法具有明显的优势。方法用于实际土样的测定,所得结果与索氏抽提的结果相当。     

微波法提取水蓼中总黄酮的工艺研究

研究了水蓼中总黄酮的微波提取最佳工艺。采用单因素试验和正交试验考察微波功率、乙醇浓度、微波辐射时间、料液比对水蓼中总黄酮提取率的影响,优选提取工艺。最佳工艺条件为:微波功率为520W,乙醇浓度为60%,微波辐射60s,间歇辐射3次,料液比为1g∶20mL。结果表明,微波提取具有提取率高、提取速度快等特点,用于中草药的提取应用前景广阔。     

微波辅助萃取鬼箭羽叶中芦丁和槲皮素

建立了鬼箭羽中主要有效成分芦丁和槲皮素的MAE-HPLC定量分析方法, 该方法具有测定准确、操作简便和分析速度快等优点. 此外, 利用扫描电镜观察了鬼箭羽叶经微波辅助萃取后植物结构的变化, 初步证明了微波辅助萃取鬼箭羽叶的萃取机理符合细胞破壁学说.     

Comparison of microwave-assisted extraction of aloe-emodin in aloe with Soxhlet extraction and ultrasound-assisted extraction

This paper reports the extraction of aloe-emodin from aloe by microwave-assisted extraction.The effects of various factors,including the solvent,the ratio (mL/g) of the solvent to the sample,microwave irradiation time and microwave power,were discussed in the experiments.The yield of aloe-emodin was determined by HPLC.The optimized conditions for microwave-assisted extraction of aloe-emodin were concluded as follows: the solvent is 80% ethanol (V/V) solution,microwave irradiation time is 3 min and microwave...     

微波辅助提取-气相色谱质谱联用测定肉桂中的挥发油

利用非极性溶剂微波辅助提取(NPSMAE)-气相色谱质谱联用研究了肉桂中的挥发油成分, 并测定了挥发油中的主要成分肉桂醛(Cinnamaldehyde)的含量. 考察了NPSMAE提取溶剂的种类、提取温度、提取时间及固液比等对测定的影响, 同时将NPSMAE与超声波辅助提取(UAE)及水蒸气蒸馏(HD)等方法进行了比较. 结果表明, 与常规提取方法相比, NPSMAE具有提取时间短、提取产率高等优点, 是一种实用的中药挥发油提取方法.     

Determination of adipate plasticizers in poly(vinyl chloride) by microwave-assisted extraction

A new method based on the application of microwave radiation to the extraction of adipate plasticizers from poly(vinyl chloride) PVC plastics is described. The experimental conditions for microwave-assisted extraction (i.e. extracting solvent, temperature, time and microwave power) were evaluated in terms of recovery. The optimisation was carried out with pastes of PVC plastified with di-2-ethylhexyl adipate, and extracts were measured by gas chromatography with flame ionization detection. Six different adipate plasticizers were studied, and microwave-assisted extraction was compared with supercritical fluid extraction for the extraction of adipates and phthalates from PVC matrices. It has been observed that the microwave-assisted extraction parameters evaluated are tightly interconnected. It has been shown that the efficiency of microwave-assisted extraction depends on the kind of solvent, the temperature achieved and the heating time. Moreover, the final temperature reached depends on the microwave power, the number of vessels and the irradiation time. On the other hand, microwave-assisted extraction provides higher recovery values than supercritical fluid extraction for both phthalate and adipate plasticizers.     

Microwave-assisted extraction performed in low temperature and in vacuo for the extraction of labile compounds in food samples

In this study, low temperature vacuum microwave-assisted extraction, which simultaneous performed microwave-assisted extraction (MAE) in low temperature and in vacuo environment, was proposed. The influencing parameters including solid/liquid ratio, extraction temperature, extraction time, degree of vacuum and microwave power were discussed. The predominance of low temperature vacuum microwave-assisted extraction was investigated by comparing the extraction yields of vitamin C, β-carotene, aloin A and astaxanthin in different foods with that in MAE and solvent extraction, and 5.2–243% increments were obtained. On the other hand, the chemical kinetics of vitamin C and aloin A, which composed two different steps including the extraction step of analyte transferred from matrix into solvent and the decomposition step of analyte degraded in the extraction solvent, were proposed. All of the decomposition rates (K₂) for the selected analyte in low temperature, in vacuo and in nitrogen atmosphere decreased significantly comparing with that in conventional MAE, which are in agreement with that obtained from experiments. Consequently, the present method was successfully applied to extract labile compound from different food samples. These results showed that low temperature and/or in vacuo environment in microwave-assisted extraction system was especially important to prevent the degradation of labile components and have good potential on the extraction of labile compound in foods, pharmaceutical and natural products.     

Microwave-assisted Extraction of Rutin and Quercetin from Flos Sophorae

Three microwave-assisted extraction(MAE) procedures were studied. The first procedure was household microwave oven dynamic extraction(HMODE). The second procedure was special microwave oven bath extraction (SMOBE). The third procedure was microwave resonant cavity dynamic extraction (MRCDE). The results obtained by the three microwave-assisted extraction procedures were compared with those obtained by using traditional Soxhlet extraction. The results indicate that the MAE not only took a shorter time, but also simplified the procedure, and made the extraction a higher yield. At the same time the results obtained by the three MAE procedures were also compared with each other.     

Optimization of Microwave-Assisted Extraction for the Determination of Organic Flame Retardants in Acrylonitrile Butadiene Styrene

The efficiency of microwave-assisted extraction was evaluated for the determination of flame retardants in acrylonitrile butadiene styrene by optimization of the temperature, time, and solvent. A quality control sample containing 500 milligrams per kilogram Dechlorane Plus, 1000 milligrams per kilogram tetrabromobisphenol A, and 1000 milligrams per kilogram triphenyl phosphate was employed. The flame retardant concentrations obtained by microwave-assisted extraction at 120 degrees Celsius for ten minutes in tetrahydrofuran were in agreement with those for the quality control sample. The efficiency of microwave-assisted extraction was comparable to ultrasonic and Soxhlet extraction used as reference techniques. In addition, the repeatabilities of the analyses, represented as relative standard deviations, were comparable: 0.8–3.4 percent for microwave-assisted extraction, 0.3–3.3 percent for ultrasonic extraction, and 0.2–8.5 percent for Soxhlet extraction. These results suggest that microwave-assisted extraction is suitable for the determination of Dechlorane Plus, tetrabromobisphenol A, and triphenyl phosphate in acrylonitrile butadiene styrene.     

Factors Controlling Leaching of Polycyclic Aromatic Hydrocarbons from Petroleum Source Rock Using Nonionic Surfactant

The extraction of polycyclic aromatic hydrocarbons (PAHs) from petroleum source rock by nonionic surfactants with the assistance of microwave irradiation was investigated and the conditions for maximum yield were determined. The results showed that the extraction temperatures and type of surfactant have significant effects on extraction yields of PAHs. Factors such as surfactant concentration, irradiation power, sample/solvent ratio and mixing surfactants (i.e., mixture of surfactant at specific ratio) also influence the extraction efficiencies for these compounds. The optimum temperature for microwave-assisted nonionic surfactant extraction of PAHs from petroleum source rock was 120 °C and the best suited surfactant was Brij 35. The new method showed extraction efficiencies comparable to those afforded by the Soxhlet extraction method, but a reduction of the extraction times and environmentally friendliness of the new nonionic surfactant extraction system are clear advantages. The results also show that microwave-assisted nonionic surfactant extraction is a good and efficient green analytical preparatory technique for geochemical evaluation of petroleum source rock.