高利用率多壁碳纳米管负载金铂合金纳米粒子催化剂在碱性溶液中的甲醇电催化氧化性能研究

使用乙二醇还原法合成了一系列高利用率多壁碳纳米管负载的金铂双金属纳米粒子电催化剂,在碱性溶液中由循环伏安和计时电流法测试该AuPt催化剂对于甲醇氧化反应的电催化活性.透射电子显微镜、X射线衍射与X射线能谱观测催化剂形貌,表征催化剂结构.结果表明,金铂双金属纳米粒子均匀分散在碳纳米管上,催化剂具有良好甲醇电氧化性能.实验表明Au/Pt/MWCNTs比为10∶8∶32(bymass)时,该催化剂具有最高甲醇电氧化峰电流密度与最负起始氧化电位.     

石墨烯负载Pt-Pd催化剂的制备、催化制氢性能及机理研究

以氧化石墨烯为载体,采用乙醇共还原法制备了石墨烯负载Pt-Pd双金属纳米催化剂,并将其用于催化碱性硼氢化钾(KBH_4)水解制氢研究.采用X射线衍射(XRD)分析和透射电子显微镜(TEM)等手段表征了催化剂的微观形貌和结构,发现当金属催化剂中Pt/Pd摩尔比为1∶1时,Pt-Pd双金属催化剂颗粒可均匀地负载于石墨烯载体表面,而且粒径比单金属催化剂和其它组成的双金属催化剂粒径更小,约为5.6 nm.将该催化剂用于催化碱性条件下KBH_4水解制氢实验,结果表明,金属催化剂的化学组成对其催化性能有明显影响,当Pt/Pd摩尔比为1∶1时其催化活性高于其它化学组成(Pt/Pd摩尔比为4∶1或1∶4)的Pt-Pd双金属催化剂,催化活性可达4380 mol_(H2)·mol_M~(-1)·h~(-1),比Pt单金属催化剂活性提高约52%,为Pd单金属催化剂活性的4倍.通过催化反应动力学研究发现,Pt-Pd双金属催化剂催化KBH_4水解制氢反应的活化能约为20.90k J/mol,催化剂具有较佳的耐久性,连续使用3次后催化效率仍可达首次催化反应效率的83%.利用密度泛函理论研究了催化剂催化KBH_4水解反应的机制,发现双金属纳米催化剂可以明显降低硼氢化物水解反应决速步骤基元反应的势垒,从而显著提高催化剂的催化活性.     

高活性甲醇氧化电催化剂Pt-Pd纳米合金的组分可控合成

Pt纳米粒子由于其本身独特的物理、化学性质以及能够同时促进氧化和还原反应,在工业生产和商业设备中(尤其在直接甲醇燃料电池中)广泛用作重要的电催化剂.然而,Pt作为贵金属在自然界中的含量极其稀少,价格昂贵;另外,甲醇氧化反应中产生的中间产物CO很容易市Pt纳米粒子中毒而失活.因此,迫切需要一种Pt用量少,催化性能高的材料.一制备高活性比表面积的Pt纳米颗粒,可以有效提高Pt利用率.另外,调控纳米粒子使其裸露特定的晶面、边、角以及缺陷也能有效提升催化性能.还可以采用Pt纳米粒子结合其它金属元素形成双金属合金,如,Pt-M (M = Pd,Au,Ag,Ru,Fe,Co,Ni,等)催化剂,可以在减少Pt元素用量的同时有效提升催化活性.在众多可供选择的元素中,Pd相对于Pt价格低廉,但两者具有相近的物理、化学性质以及较高的电催化性能,使Pt-Pd纳米合金呈现十分优异的电催化性能.研究表明,Pt-Pd纳米合金在酸性和CO环境中能有效催化有机小分子电氧化过程.另外,在酸性环境中,用Pd替代Cu,Ag,Co或Ni,可以有效减少催化剂的腐蚀.本文在乙二醇溶液中同时还原K2PtCl4和Na2PdCl4,在110 ℃C反应5 h制备出超细的Pt-Pd纳米合金.通过X射线衍射(XRD)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)以及能谱仪(EDS)对合金进行表征,从而确定产物为尺寸4 nm左右的Pt-Pd纳米合金,且通过改变金属前驱体的投料比可以有效调控Pt-Pd合金组分(按元素比例分别表示为Pt1Pd3,Pt1Pd1,Pt3Pd1).采用循环伏安法、线性扫描伏安法以及计时安培法等多种手段测试样品在0.5 mol/L H2SO4和0.5 mol/L CH3OH的酸性环境中(50 mV/s)电化学性能,并与商业Pt/C进行比较.结果表明,合金的催化性能和组分密切相关,当Pt元素的含量为75%左右时,Pt-Pd纳米合金表现出最佳的催化活性和稳定性,其中Pt3Pd1的电催化质量活性可达商业Pt/C的7倍之多.我们把Pt-Pd纳米合金的催化性能对其组分的依赖性归结为甲醇氧化反应中的双官能团机制,反应中,Pt可有效催化甲醇脱氢产生Pt-CO,Pd则催化水脱氢形成Pd-OH.当Pd含量减少时,Pt表面的水脱氢反应只有在高电位才能发生,从而降低催化效率;而Pd含量过多,则会抑制Pt催化甲醇的脱氢反应,使催化效率大大降低.因此,只有适宜Pt/Pd比例,才能有效提升催化效率.     

高活性甲醇氧化电催化剂Pt-Pd纳米合金的组分可控合成（英文）

Pt纳米粒子由于其本身独特的物理、化学性质以及能够同时促进氧化和还原反应,在工业生产和商业设备中(尤其在直接甲醇燃料电池中)广泛用作重要的电催化剂.然而,Pt作为贵金属在自然界中的含量极其稀少,价格昂贵;另外,甲醇氧化反应中产生的中间产物CO很容易市Pt纳米粒子中毒而失活.因此,迫切需要一种Pt用量少,催化性能高的材料.一制备高活性比表面积的Pt纳米颗粒,可以有效提高Pt利用率.另外,调控纳米粒子使其裸露特定的晶面、边、角以及缺陷也能有效提升催化性能.还可以采用Pt纳米粒子结合其它金属元素形成双金属合金,如,Pt-M(M=Pd,Au,Ag,Ru,Fe,Co,Ni,等)催化剂,可以在减少Pt元素用量的同时有效提升催化活性.在众多可供选择的元素中,Pd相对于Pt价格低廉,但两者具有相近的物理、化学性质以及较高的电催化性能,使Pt-Pd纳米合金呈现十分优异的电催化性能.研究表明,Pt-Pd纳米合金在酸性和CO环境中能有效催化有机小分子电氧化过程.另外,在酸性环境中,用Pd替代Cu,Ag,Co或Ni,可以有效减少催化剂的腐蚀.本文在乙二醇溶液中同时还原K_2PtCl_4和Na_2PdCl_4,在110°C反应5 h制备出超细的Pt-Pd纳米合金.通过X射线衍射(XRD)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)以及能谱仪(EDS)对合金进行表征,从而确定产物为尺寸4 nm左右的Pt-Pd纳米合金,且通过改变金属前驱体的投料比可以有效调控Pt-Pd合金组分(按元素比例分别表示为Pt1Pd3,Pt1Pd1,Pt3Pd1).采用循环伏安法、线性扫描伏安法以及计时安培法等多种手段测试样品在0.5 mol/L H_2SO_4和0.5mol/L CH_3OH的酸性环境中(50 mV/s)电化学性能,并与商业Pt/C进行比较.结果表明,合金的催化性能和组分密切相关,当Pt元素的含量为75%左右时,Pt-Pd纳米合金表现出最佳的催化活性和稳定性,其中Pt_3Pd_1的电催化质量活性可达商业Pt/C的7倍之多.我们把Pt-Pd纳米合金的催化性能对其组分的依赖性归结为甲醇氧化反应中的双官能团机制,反应中,Pt可有效催化甲醇脱氢产生Pt-CO,Pd则催化水脱氢形成Pd-OH.当Pd含量减少时,Pt表面的水脱氢反应只有在高电位才能发生,从而降低催化效率;而Pd含量过多,则会抑制Pt催化甲醇的脱氢反应,使催化效率大大降低.因此,只有适宜Pt/Pd比例,才能有效提升催化效率.     

原位合成钴/还原氧化石墨烯纳米粒子催化氨硼烷制氢

采用简单的原位还原合成方法,利用具有温和还原性能的氨硼烷作为还原剂,在室温下一步还原氧化石墨烯和氯化钴混合溶液制备了还原氧化石墨烯负载钴纳米复合材料催化剂. 利用所制备的钴/还原氧化石墨烯催化剂催化氨硼烷水解制氢,发现钴/还原氧化石墨烯具有优异的催化性能. 相对于没有负载的钴纳米粒子以及采用硼氢化钠作为还原剂制备的钴/还原氧化石墨烯催化剂,采用氨硼烷还原制备的钴/还原氧化石墨烯催化剂表现出更加优越的催化性能. 动力学测试表明,钴/还原氧化石墨烯催化氨硼烷水解反应为零级反应,同时钴/还原氧化石墨烯催化剂催化氨硼烷水解反应的活化能为27.10 kJ·mol^-1,低于大部分已报道的其它催化剂,甚至一些贵金属催化剂的活化能. 钴/还原氧化石墨烯催化剂有着稳定的循环使用性,特别是其具有的磁性使得它能够直接从溶液中通过磁力回收,极具应用前景. 这种简单有效的合成方法有望推广到其它的金属-还原氧化石墨烯纳米复合材料体系.     

石墨烯负载Pt/Co双金属纳米颗粒催化剂的制备及催化制氢性能

采用化学共还原方法制备了石墨烯负载Pt/Co双金属纳米颗粒（GBNPS）催化剂,并将其用于催化硼氢化钾（KBH₄）水解制氢.采用透射电子显微镜（TEM）、X射线衍射（XRD）仪和X射线光电子能谱（XPS）表征了该催化剂,并研究了双金属纳米颗粒的化学组成对其催化KBH₄水解制氢性能的影响.结果表明,制备的石墨烯负载Pt/Co双金属纳米颗粒平均粒径为3.2~3.9 nm,其中石墨烯负载Pt₂₀Co₈₀双金属纳米颗粒的催化活性最高,35℃时制氢活性可达35973 mol_H2·h^-1·mol^-1_Pt,且具有良好的耐久性,催化KBH₄水解反应的表观活化能为36 kJ/mol.     

直接甲醇燃料电池阳极催化剂的新体系: 纳米TiO2-CNT-PtNi复合纳米催化剂

采用电合成前驱体Ti(OEt)₄直接水解法和电化学扫描电沉积法制备纳米TiO₂-CNT-PtNi复合纳米催化剂. 透射电镜(TEM)和X射线衍射(XRD)测试结果表明, 纳米PtNi合金粒子(平均粒径8 nm)均匀地分散在纳米TiO₂-CNT复合膜的三维网络结构中. 通过暂态电化学方法研究表明, 复合纳米催化剂的电化学活性比表面积为90 m²/g, 对甲醇氧化具有很高的电催化活性和稳定性, 常温常压下甲醇氧化峰电位为0.67和0.44 V, 当温度为60 ℃时, 氧化峰电位负移至0.64和0.30 V, 氧化峰电流密度高达1.38 A/cm². 复合纳米催化剂对甲醇电氧化的高催化活性和稳定性可归因于多元复合纳米组分的协同催化作用, 这种作用导致CO在复合纳米催化剂上的弱吸附, 从而避免了催化剂的中毒.     

铜纳米粒子负载于钴纳米片的双金属催化剂催化CO选择性加氢

使用赖氨酸作为表面活性剂模板, 合成了Cu纳米粒子负载于Co纳米片的双金属催化剂Cu/Co. 与常规的Cu-Co双金属纳米颗粒催化剂相比, Cu/Co催化剂对CO选择性加氢反应表现出特殊的结构效应, 提高了CO转化率和高级醇选择性, 降低了甲烷选择性. Cu/Co催化剂中, Cu(111)面与Co(100)面相互作用的功能化界面有利于深入研究金属-金属的相互作用. 这种双金属催化剂可以将模型催化剂和现实催化应用联系起来, 将有助于获得对合成气转化制高级醇反应机理的本质认识.     

氮掺杂石墨烯量子点/钯纳米复合材料的研究

铂基催化剂因具有高催化活性、高稳定性而成为极其重要的能源转化催化剂。本文采用水热法合成氮掺杂石墨烯量子点支撑的钯纳米复合材料(Pd@N-GQDs),并将其用于碱性介质中甲醇的电催化氧化反应。实验结果表明,相比同类型材料钯负载于石墨烯纳米片(Pd@GS)、钯负载于石墨烯量子点(Pd@GQDs)和商业钯黑催化剂(Pd@C),Pd@N-GQDs纳米材料具有很高的催化活性和稳定性,并可减少催化剂材料中贵金属的使用量。     

直接甲醇燃料电池阳极催化剂的新体系: 纳米TiO2-CNT-PtNi复合纳米催化剂

采用电合成前驱体Ti(OEt)4直接水解法和电化学扫描电沉积法制备纳米TiO2-CNT-PtNi复合纳米催化剂.透射电镜(TEM)和X射线衍射(XRD)测试结果表明,纳米PtNi合金粒子(平均粒径8 nm)均匀地分散在纳米TiO2-CNT复合膜的三维网络结构中.通过暂态电化学方法研究表明,复合纳米催化剂的电化学活性比表面积为90 m2/g,对甲醇氧化具有很高的电催化活性和稳定性,常温常压下甲醇氧化峰电位为0.67和0.44 V,当温度为60℃时,氧化峰电位负移至0.64和0.30V,氧化峰电流密度高达1.38Mcm2.复合纳米催化剂对甲醇电氧化的高催化活性和稳定性可归因于多元复合纳米组分的协同催化作用,这种作用导致CO在复合纳米催化剂上的弱吸附,从而避免了催化剂的中毒.     

还原剂对Au-Pd/CeO2催化剂甲醇部分氧化性能的影响

以PVP为保护剂,乙醇(ER)、乙二醇(GR)和水合肼(HR)为还原剂制备了一系列Au-Pd/CeO2催化剂,考察了还原剂对甲醇部分氧化性能的影响,并运用XRD、TPD和TPR等手段对催化剂进行了表征。结果表明,Au-Pd/CeO2(ER)催化剂具有较大的比表面积,形成的AuxPdy量较多、粒径较小、分散度较高、活性组分与载体的相互作用较强,同时对甲醇的吸附量较大和吸附温度较低。因此,该催化剂具有较高的催化活性和氢气选择性以及较低的CO质量分数。     

还原态氧化石墨烯载Pd纳米催化剂对甲酸氧化的电催化性能

采用改进的Hummers法氧化石墨后,对其超声剥离成氧化石墨烯水溶液,继之通过乙二醇还原Pd金属离子和氧化石墨烯,得到了还原态氧化石墨烯（RGO）负载Pd纳米催化剂,并用于甲酸的电催化氧化.透射电子显微镜和X射线衍射结果显示：负载于RGO上的Pd粒子平均粒径为3.8nm,其优先在RGO的褶皱和边缘处生长.电化学测试表明：RGO上残存的含氧基团降低了Pd催化剂受CO毒化的程度,Pd/RGO催化剂表现出了较商业化Pd/C更高的电催化活性和更好的稳定性.     

Electrocatalytic oxidation of methanol on Pt-Pd nanoparticles supported on honeycomb-like porous carbons in alkaline media

Honeycomb-like porous carbons (PCs) were synthesized using a facile self-assembly method with phenolic resin as the carbon source and tetraethyl orthosilicate (TEOS) as the silica source. The PCs were found to have a large BET surface area of 458 m² g^?1 and a partially graphitized structure. The obtained PCs were used as a support for various Pt-Pd bimetallic alloy catalysts employed for methanol oxidation in alkaline media. Compared with Pt supported on commercial Vulcan XC-72R carbon (Pt/C) and with the other Pt-Pd bimetallic alloy catalysts on PCs, Pt₃Pd₁ on PCs displayed the most negative onset potential for methanol oxidation and the highest steady-state current (2.04 mA cm^?2). This may be because the Pt₃Pd₁/PCs catalyst has the largest electrochemical active surface area (ESA), and because adding Pd to the catalyst improves the ability of the intermediate species to tolerate oxidation. The results show that the prepared Pt-Pd/PCs is a potential candidate for application as a catalyst in alkaline direct methanol fuel cells.     

Sonochemical synthesis of graphene oxide supported Pt–Pd alloy nanocrystals as efficient electrocatalysts for methanol oxidation

Pt–Pd bimetallic nanoparticles supported on graphene oxide (GO) nanosheets were prepared by a sonochemical reduction method in the presence of polyethylene glycol as a stabilizing agent. The synthetic method allowed for a fine tuning of the particle composition without significant changes in their size and degree of aggregation. Detailed characterization of GO-supported Pt–Pd catalysts was carried out by transmission electron microscopy (TEM), AFM, XPS, and electrochemical techniques. Uniform deposition of Pt–Pd nanoparticles with an average diameter of 3 nm was achieved on graphene nanosheets using a novel dual-frequency sonication approach. GO-supported bimetallic catalyst showed significant electrocatalytic activity for methanol oxidation. The influence of different molar compositions of Pt and Pd (1:1, 2:1, and 3:1) on the methanol oxidation efficiency was also evaluated. Among the different Pt/Pd ratios, the 1:1 ratio material showed the lowest onset potential and generated the highest peak current density. The effect of catalyst loading on carbon paper (working electrode) was also studied. Increasing the catalyst loading beyond a certain amount lowered the catalytic activity due to the aggregation of metal particle-loaded GO nanosheets.     

Precisely Controlled Synthesis of Pt-Pd Octahedral Nanoframes as a Superior Catalyst towards Oxygen Reduction Reaction

Pt-based nanoframes represent a class of promising catalysts towards oxygen reduction reaction. Herein, we, for the first time, successfully prepared Pt-Pd octahedral nanoframes with ultrathin ridges less than 2 nm in thickness. The Pt-Pd octahedral nanoframes were obtained through site-selected deposition of Pt atoms onto the edge sites of Pd octahedral seeds, followed by selective removal of the Pd octahedral cores via chemical etching. Due to that a combination of three-dimensional opens geometrical structure and Pt-skin surface compositional structure, the Pt-Pd octahedral nanoframes/C catalyst shows a mass activity of 1.15 A/mg_Pt towards oxygen reduction reaction, 5.8 times enhancement in mass activity relative to commercial Pt/C catalyst (0.20 A/mg_Pt). Moreover, even after 8000 cycles of accelerated durability test, the Pt-Pd octahedral nanoframes/C catalyst still exhibits a mass activity which is more than three times higher than that of pristine Pt/C catalyst.     

不同温度焙烧的Au-Pd/SiO2催化剂上甲醇选择性氧化制备甲酸甲酯

以溶胶固定法制备了Au-Pd/SiO₂催化剂,考察了催化剂焙烧温度对甲醇选择氧化制甲酸甲酯反应性能的影响。在200~500℃,400℃焙烧的Au-Pd/SiO₂具有最好的低温催化性能,在室温下就有活性,反应温度为100℃时甲醇转化率为25.3%,甲酸甲酯的选择性为100%。采用BET、XRD、UV-vis DRS、XPS、TEM和DRIFTS技术对催化剂进行表征,结果表明,催化剂中活性组分Au和Pd的高分散性,合适的Au和Pd粒径,Au-Pd合金的形成以及Au和Pd之间的强相互作用力,有利于甲醇氧化为甲酸甲酯反应的进行。初步推测出了甲醇在Au-Pd/SiO₂上氧化为甲酸甲酯的反应机理,甲醇在Au-Pd/SiO₂催化剂上是通过甲氧基中间体得到甲酸甲酯的。     

A general method for the rapid synthesis of hollow metallic or bimetallic nanoelectrocatalysts with urchinlike morphology

We have reported a facile and general method for the rapid synthesis of hollow nanostructures with urchinlike morphology. In-situ produced Ag nanoparticles can be used as sacrificial templates to rapidly synthesize diverse hollow urchinlike metallic or bimetallic (such as Au/Pt) nanostructures. It has been found that heating the solution at 100 degrees C during the galvanic replacement is very necessary for obtaining urchinlike nanostructures. Through changing the molar ratios of Ag to Pt, the wall thickness of hollow nanospheres can be easily controlled; through changing the diameter of Ag nanoparticles, the size of cavity of hollow nanospheres can be facilely controlled; through changing the morphologies of Ag nanostructures from nanoparticle to nanowire, hollow Pt nanotubes can be easily designed. This one-pot approach can be extended to synthesize other hollow nanospheres such as Pd, Pd/Pt, Au/Pd, and Au/Pt. The features of this technique are that it is facile, quick, economical, and versatile. Most importantly, the hollow bimetallic nanospheres (Au/Pt and Pd/Pt) obtained here exhibit an area of greater electrochemical activity than other Pt hollow or solid nanospheres. In addition, the approximately 6 nm hollow urchinlike Pt nanospheres can achieve a potential of up to 0.57 V for oxygen reduction, which is about 200 mV more positive than that obtained by using a approximately 6 nm Pt nanoparticle modified glassy carbon (GC) electrode. Rotating ring-disk electrode (RRDE) voltammetry demonstrates that approximately 6 nm hollow Pt nanospheres can catalyze an almost four-electron reduction of O(2) to H(2)O in air-saturated H(2)SO(4) (0.5 M). Finally, compared to the approximately 6 nm Pt nanoparticle catalyst, the approximately 6 nm hollow urchinlike Pt nanosphere catalyst exhibits a superior electrocatalytic activity toward the methanol oxidation reaction at the same Pt loadings.     

Controllable fabrication of platinum nanospheres with a polyoxometalate-assisted process

Pt nanospheres with an average diameter of 60±10 nm have been successfully synthesized at room temperature through a facile polyoxometalate(POM)-assisted process. Characterization by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) clearly showed that these Pt nanospheres consisted of 2-7 nm Pt nanodots. During the formation of such unique nanostructures, POMs were found to serve as both catalyst and stabilizer. The size of the as-synthesized Pt nanospheres could be controlled solely by adjusting the molar ratio of POMs to H₂PtCl₆. A possible formation mechanism based on POMs-mediated electron transfer from ascorbic acid (AA) to PtCl₆²⁻ and AA-assisted aggregation was tentatively proposed to rationalize the formation of such nanostructures. Importantly, these specific Pt nanospheres exhibited good electrocatalytic activity towards the oxidation of methanol, making them promising for applications in direct methanol fuel cells.     

Enhanced Electrocatalytic Activity of Methanol and Ethanol Oxidation in Alkaline Medium at Bimetallic Nanoparticles Electrochemically Decorated Fullerene-C60 Nanocomposite Electrocatalyst: An Efficient Anode Material for Alcohol Fuel Cell Applications

Direct alcohol fuel cells (DAFCs) have been recently playing a pivotal role in electrochemical energy sources and portable electronics. Research in DAFCs has proceeded to engage major attention due to their high catalytic activity, long-term stability, portability, and low cost. Herein, we present a facile surfactant-free route to anchor bimetallic Pd−W nanoparticles supported fullerene-C₆₀ catalyst (Pd-W@Fullerene-C₆₀) for high-performance electrooxidation of alcohols (methanol & ethanol) for DAFCs applications. Structural, elemental composition, and morphological analysis of the proposed catalyst were carried out using UV-Vis spectroscopy, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and energy-dispersive x-ray spectroscopy (EDX). Electrochemical properties such as electrochemical activity, electrochemical active surface area (ECSA), and long-term stability of the Pd-W@Fullerene-C₆₀ catalyst for ethanol and methanol oxidation in the alkaline medium were explored by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry (CA). Results revealed that the proposed catalyst showed enlarged ECSA, tremendous electrocatalytic activity, high poison tolerance limit, good reproducibility, and enhanced long-term stability as compared to the monometallic catalyst and commercially available catalyst (Pt/C) towards ethanol and methanol oxidation reaction. This enhanced potentiality of the Pd-W@Fullerene-C₆₀ catalyst is due to the synergistic effect of W−Pd nanoparticles and excellent electron kinetic from fullerene support material. These findings strongly suggest the Pd-W@Fullerene-C₆₀ catalyst as potential anode material for the alcohol oxidation reaction.     

甲烷直接催化氧化制备甲醇近期研究进展北大核心CSCD

甲烷合成甲醇的方法包括间接法和直接催化氧化(DMTM)法,但是间接法对设备要求高,且甲烷转化率与甲醇选择性均不理想,DMTM法可通过一步反应高选择性制备甲醇,有巨大的应用潜力。对于甲烷DMTM法合成甲醇,均相催化体系通常需要特殊反应介质与贵金属催化剂相结合,虽然反应效率高,但对反应设备有腐蚀性,产物不易分离,应用前景差。液相-异相催化一般使用H_(2)O_(2)作为氧化剂,Au、Pd、Fe和Cu等金属元素作为催化剂主要活性组分,·OH是主要的氧化活性物,可在低温下实现甲烷的活化氧化。因此,异相催化体系是目前研究的主流。气相-异相催化主要使用O_(2)和N_(2)O为氧化剂,前者氧化性更强,后者对于产品选择性更好,此外,厌氧体系中H_(2)O也可直接作为氧供体,常用Cu、Fe、Rh等元素作为催化剂。沸石分子筛是使用最广泛的载体,金属氧化物、金属有机骨架化合物(MOFs)和石墨烯也均有涉及,多金属协同催化已经取得了很好的效果。本文主要总结与概述了热催化甲烷直接催化氧化制备甲醇的近年相关研究,并对今后的研究方向做出了展望。