1,3,3-三硝基氮杂环丁烷的热安全性

借助不同加热速率(β)的非等温DSC曲线离开基线的初始温度(T₀)、onset温度(T_e)和峰顶温度(T_p), Kissinger法和Ozawa法求得的热分解反应的表观活化能(E_k和E_O)和指前因子(A_k), Hu-Zhao-Gao方程ln β_i＝ln[A₀/(b_{e0 or p0}G(α))]＋   b_{e0 or p0}T_{ei or pi}求得的b_{e0 or p0}, Zhao-Hu-Gao方程ln β_i＝ln[A₀/((a_{e0 or p0}＋1)G(α))]＋(a_{e0 or p0}＋1) ln T_{ei or pi}求得的a_{e0 or p0}, 微热量法确定的比热容(C_p), 以及密度(ρ)、热导率(λ)和分解热(Q_d, 取爆热之半)数据, Zhang-Hu-Xie-Li公式、Hu-Yang-Liang-Xie公式、Hu-Zhao-Gao公式、Zhao-Hu-Gao公式、Smith方程、Friedman公式和Bruckman-Guillet公式, 计算了TNAZ在β→0时的T₀, T_e和T_p值(T₀₀, T_eo和T_p0)、热爆炸临界温度(T_be和T_bp)、绝热至爆时间(t_Tlad)、撞击感度50%落高(H₅₀)和热点起爆临界温度(T_cr), 得到了评价TNAZ热安全性的结果: T_SADT＝T_e0＝485.81 K, T_p0＝497.38 K, T_beo＝499.50 K, T_bp0＝513.45 K, t_Tlad＝8.90 s (n＝0), t_Tlad＝8.96 s (n＝1), t_Tlad＝9.01 s (n＝2), H₅₀＝28.88 cm, T_cr＝641.46 K (T_room＝293.15 K), T_cr＝658.89 K (T_room＝300 K), 表明: (1) TNAZ对热是稳定的; (2)撞击感度好于环三亚甲基三硝胺(RDX); (3)热点起爆临界温度高于RDX, 而界于1,3,5-三氨基-2,4,6-三硝基苯(TATB)和六硝基茋(HNS)之间.     

热致液晶性序列嵌段共聚酯的多重热转变

本文利用DSC研究了热致液晶性序列嵌段共聚酯在不同升温速率时的多重熔融转变,和不同冷却速率对结晶与熔融过程的影响。发现T_(kn)和T_(ni)与热历史、升温速率及成形条件均无关,T_(kn)=425.86K,T_(nt)=480.60K;而T_(in)与T_(nk)随冷却速率增大而降低。     

Limitations of some esterification techniques in structural studies of kerogen-derived acids

Oxidative degradation techniques for characterizing kerogens in oil shales often lead to major yields of precipitated acids (PA), which are less amenable than soluble acid products to analysis by gas chromatography/mass spectrometry (g.c./m.s.). A PA complex produced by oxidation of a Julia Creek (Queensland) kerogen was studied by applying four different esterification techniques before g.c./m.s. Methods based on reaction with diazomethane or boron trifluoride/methanol were of limited effectiveness. Reaction with dimethyl sulphate in acetone with potassium carbonate catalyst led to the detection of by far the widest range of components in the PA complex. This method is recommended for esterifying acid products derived from kerogen, especially in comparative characterization studies of kerogens.     

取代羧酸pKa的分子树拓扑研究

基于非氢原子i的酸性点价(δai)建构分子树拓扑指数(mT)及其分支指数(mTC)和叶指数(mTx),并提出表征诱导效应的叶指数(mT′x).通过最佳变量子集算法获得38种羧酸的pKa与0TC、1TC、0T′x的回归方程:pKa=3.0352-1.25700T′x-0.15540TC+0.07811TC,R=0.9766.通过Jackknife法检验,该模型具有总体稳健性.优于文献的七元最佳回归模型(R=0.957),与其分子力学方法(CoMFA)结果(R=0.988)较为接近.结果表明,所建拓扑指数是合理的,具有科学性基础.     

PEO/LiClO_4复合体系电解质膜的固体NMR研究

自1973年,Wright[1]等发现聚氧乙烯(PEO)/碱金属盐复合物具有离子导电性之后,人们对复合物的导电机理以及如何进一步提高复合物导电率等问题开展了大量研究.长期以来,人们普遍认为复合物中碱金属离子的传输是通过PEO非晶区的链段运动来实现的[2],因此探索新的物理或化学方法,通     

单臂冠醚的结构与液晶性质

设计并合成了３个低温冠醚液晶－单臂脂环冠醚液晶，考察了冠醚结构与液晶性质的关系，单臂冠醚液晶分子具有液晶蛋白质应满足长径比大于３，分子具有一定的平面特性和能通过引入手性基团使单臂冠醚液晶分子产生手性近晶相等条件。     

微量热法测定细菌的临界生长温度

应用微量热学的方法,我们已能成功地测得细菌生长过程的热谱,这种热谱包含着有关细菌生长代谢过程的丰富信息,例如对热谱曲线的指数生长段进行解析,可得出细菌生长的速率常数、激活能和有关的热力学参数。故采用微量热法测定细菌在不同培养温度下的生长速率常数,利用计算机拟合出相应k(速率常数)和T(培养温度)的线性关系式后,若把生长速率为零的温度定义为临界生长温度时,就可以根据由上述实验所得的k～T线性关系式求得细菌的临界生长温度。本工作仍采用微量热法对福氏志贺氏菌(S. flexneri)和大肠埃希氏菌(E. coli)进行实验测定。按文献的方法求出它们在不同温度下的生长速率常数;对于大肠埃希氏菌还用几种不同的培养基分别进行实验测定。     

微量热法测定细菌的临界生长温度

In this paper, we have determined the multiplication rate constanis (k) of Shigella flexneri and E. coli. at different temperatures and in different culture media by means of a microcalorimeter. From these results a linear equation as k~(1/2)=a+bT can be established for the bacterial growth. The corresponding linear equation for S. flexneri is k~(1/2)=-1.2823+0.0047122 T(r=0.971), so its eritica lgrowth temperature T_0 is equal to 272.1 K. The linear equation for E coli is k~(1/2)=-1.6390+0.005948 T (r=0.994), T_0=275.5 K. The experimental results indicate that the critial growth temperature of E. coli. is nearly a constant (T_0=273.9 K) in different culture media, which is very informative for the study on microorganism growth.     

自聚集在纳米金粒上的烷基硫醇单分子层的NMR驰豫时间研究

通过质子的自旋-晶格驰豫时间（T_1）、自旋-自旋驰豫时间（T_2）研究烷基 巯基[X(CH_2)_nS-]单分子层保护的纳米金粒中配体分子的运动。本研究涉及两种 典型配体：CH_3(CH_2)_7SH和Py(CH_2)_(12)SH及该两配体的不同配比的测合配体 。实验监测了配体中不同位置的质子的NMR驰豫时间随空间距离及配体比例改变的 变化情况。不同位置的质子,因主要影响因素的不同,表现出各自特殊的运动特征 。配体与金粒配位后,2,3位T_1,T_2值减少,1,4位T_1,T_2值增加。混合配体 中Py(CH_2)_(12)SH含量增加,1,2,3位T_1,T_2值都会减小;而4位T_1值减小, T_2值却增加;不同位置T_1,T_2值变化快慢有别。2位因其特殊位置,在配体配比 PY:C_8 = 1:1[PY代表Py(CH_2)_(12)SH,C_8代表CH_3(CH_2)_7SH]时,分子运动最 自由。实验结果显示T_1总是大于T_2,这说明配体处于低频运动区。     

PEO-LiClO4-ZSM-5复合聚合物电解质——ZSM-5对锂离子选择通过的影响

通过溶液浇铸法制得了一系列以不同分子筛和蒙脱土为填料的PEO基复合聚合物电解质,利用交流阻抗-稳态电流方法研究了填料对复合聚合物电解质锂离子迁移数(TLi+)的影响.实验结果表明,所有填料都有利于同时提高复合聚合物电解质的TLi+和离子电导率,但以Li-ZSM-5为填料时TLi+最高,这是因为ZSM-5的特殊二维孔道结构有利于阳离子Li+的进入,而排斥阴离子ClO4-的通过.较高的TLi+和室温离子电导率说明PEO-LiClO4-ZSM-5有可能作为全固态锂离子聚合物电池的电解质材料.     

四中位（邻烷基）苯基卟啉及其高铁络合物的合成及光谱性质

合成了６种不同大小的烷基取代的四中位（邻烷基）苯基卟啉Ｔ＿（Ｏ－Ｒ）ＰＰＨ＿２及其高铁络合物Ｔ＿（Ｏ－Ｒ）ＰＰＦｅＣｌ（Ｒ＝ＣＨ＿３，Ｃ＿２Ｈ＿５，ｎ－Ｃ＿３Ｈ＿７，ｉ－Ｃ＿３Ｈ＿７，ｎ－Ｂｕ，ｔ－Ｂｕ），除Ｒ＝ＣＨ＿３外，其它５种是文献未曾报道过的新化合物。测定了它们的核磁共振谱、红外及电子光谱，并讨论了它们的结构与光谱性质的关系．     

吸附在活性炭上的苯和环己烷的NMR弛豫研究

被吸附分子的NMR弛豫测量可以提供该分子的运动和吸附状态等信息。近来证明,多孔固体中被吸附物的自旋晶格弛豫的测量(T_1)是孔径大小和孔结构分析及多孔物质渗透性能测量的有力工具这是基于靠孔壁近的分子比远离固体表面的分子自旋晶格弛豫     

2-甲基噻吩光异构化成3-甲基噻吩的理论研究

用CASSCF方法以6-31G基组研究了2-甲基噻吩光异构化为3-甲基噻吩的光化学反应和基态(S₀)及三重激发态(T₁)的相关势能面.反应主要发生在三重态(T₁)上,其间经历了两个双自由基,1个三元环中间体及4个过渡态.沿着反应路径找到了2个T₁/S₀势能面交叉点,其结构都类似于双自由基.在第二个T₁/S₀势能面交叉点附近由T₁向S₀的系间窜越(ISC)最为有利.     

Theoretical study of stability, structures, and aromaticity of multiply N-confused porphyrins.

The total electronic energy and nucleus-independent chemical shift (NICS) of 95 isomers of N-confused porphyrin (NCP: normal porphyrin (N(0)CP), singly N-confused porphyrin (N(1)CP), doubly N-confused porphyrin (N(2)CP), triply N-confused porphyrin (N(3)CP), and fully N-confused porphyrin (N(4)CP)) have been calculated by the density functional theory (DFT) method. The stability of NCP decreased by increasing the number of confused pyrrole rings. Namely, the relative energies of the most stable isomers in each confusion level increased in a stepwise manner approximately by +18 kcal/mol: 0 (N(0)CP1), +17.147 (N(1)CP2), +37.461 (N(2)CPb3), +54.031 (N(3)CPd6), and +65.636 kcal/mol (N(4)CPc8). In this order, the mean plane deviation of these isomers increased from 0.000 to 0.123, 0.170, 0.215, and 0.251 A, respectively. The unusual tautomeric forms of pyrrole ring with an sp(3)-carbon were found in the stable forms of N(3)CP and N(4)CP. The NICS values at the mean position of the 24 core atoms were nearly the same for the most aromatic isomers regardless of the confusion level: -15.1280 (N(0)CP1), -13.8493 (N(1)CP2), -13.7267 (N(2)CPd1), -11.7723 (N(3)CPb5), and -13.6224 ppm (N(4)CPa6). The positive correlation between aromaticity and stability was inferred from the plots of NICS and the relative energy of NCP for N(0)CP, N(1)CP, and trans-N(2)CP. On the other hand, the correlation was negative for cis-N(2)CP, N(3)CP, and N(4)CP isomers.     

偶氮苯磺酸衍生物的光致顺反异构化机理

基于密度泛函理论(DFT)中的B3LYP方法, 在6-311++G(d,p)水平上全优化得到了3,3'-偶氮苯磺酸(3,3'-AbS)在S0和T1态顺反异构化机理.在S0态存在两种异构化途径: 绕角NNC反转和绕NC键旋转相结合的形式和单纯的绕CNNC二面角旋转形式, 两种异构化途径的能垒分别为94.2和124.3 kJ·mol-1. 有必要指出的是, 在反转与旋转结合的途径上存在二次过渡态. 在T1态上仅存在旋转途径且其能垒为21.1 kJ·mol-1. 采用含时密度泛函理论(TD-DFT), 在B3LYP/6-311++G(d,p)水平上, 沿着基态的两种异构化途径计算得到了T1, S1, T2和S2态的垂直激发的势能剖面, 分析了可能的光致异构化途径. 当激发光波长为330 nm时, 反应物分子被激发到S2态, 然后弛豫到较低的能态S1发生异构化反应, 旋转途径存在两条活化途径: (1) 沿着S1/S0的圆锥交叉点衰变到产物; (2) 由S1态弛豫到T1态后, 在S0-T1-S0的区域发生异构化, 再转化到产物. 计算结果表明, 3,3'-AbS通过反转和旋转的结合形式实现在S0态的异构化, 而被激发后倾向于沿着旋转坐标作为其主要的异构化途径.     

异氰酸光解的动态学研究

在异氰酸光解势能面研究的基础上,计算了不同电子态热能面交叉点S_1/T_1 处S_1 → T _1的态-态积累跃迁速率k_(S_1→T_1),S_1/S_0处S_1 → S_0的跃迁 速度k_(S_1→S_0),结果表明,在交叉点处态-态跃迁速度非常大,可以认为高能 态在交叉点可以直接跃迁到低能态。据此我们又根据单分子微正则过渡态理论计算 了不同光解波长下S_1态和T_1态的光解反应速度k_反~(S_1)（E）和k~(T_1)（E） 和S_1态反-顺异构化的反应速率。在光解波长为230 nm时,k_(T_1)/k_(S_1) = 9. 48,与实验值为5相接近;在低能时k~(T_1) > k_反~(S_1),获得了和实验相一致 的结果。     

The analysis of kerogens by pyrolysis—gas chromatography—mass spectrometry using selective ion monitoring: 2. Alkylnaphthalenes

Kerogens isolated from sediments have been analysed by pyrolysis—gas chromatography—mass spectrometry using the mass spectrometer as a selective ion detector. Monitoring one or more of the with m/z values of 141, 142, 156 and 170 provides information concerning the abundance and distribution of naphthalenes (containing one, two and three substituent carbon atoms) which are present in the kerogen pyrolysates. This information, which is less-readily obtainable by other means, gives some indication of the occurrence and nature of naphthalenic nuclei in kerogens. The selective ion monitoring method has also been applied to the analysis of naphthalenes in crude oils, this being a preliminary investigation of the possibility of providing information on the relationships between kerogens and crude oils.     

Removal of 4‐chlorophenol using graphene,graphene oxide,and a‐doped graphene (A = N,B): A computational study

Density functional theory (including van der Waals correction with the PBE‐D functional) is applied to the study of 4‐chlorophenol (4‐CP) adsorption on graphene oxide (GO), A‐doped graphene (A = N, B), and pristine graphene and test their possible application for 4‐CP removal. Results show that on GO adsorption is improved by the hydrogen bond interactions between the adsorbents and 4‐CP, suggesting that functionalized graphene is a preferable alternative than pristine graphene for 4‐CP removal. In addition, the stability of hydrogen bonds is confirmed by molecular dynamics calculations using the PM6 potential. Without hydrogen bonds, A‐doped graphene models show a comparable performance for 4‐CP removal than pristine graphene. Finally, even in a solvent medium, 4‐CP adsorption is strong. © 2013 Wiley Periodicals, Inc.     

氰酸酯树脂改性热固性丁苯树脂的固化及其动力学

利用傅里叶变换红外光谱法(FT-IR)和差示扫描量热法(DSC)研究了氰酸酯树脂改性热固性丁苯树脂的固化反应特性及其动力学.以温度-升温速率外推法计算得到固化反应起始温度(Ti0)、峰顶温度(Tp0)和终止温度(Tf0)分别为414.2、444.5、460.6 K,对改性树脂的固化过程进行优化.采用Freeman-Ca...