CXN天然沸石的研究VII. 骨架高硅超稳化改性

以高硅超稳化辉沸石(STI)为基底沸石, 分别经盐酸脱铝或氟硅酸铵脱铝补硅处理后制备的改性H-STI沸石, 其非骨架铝含量明显减少, 而后者骨架硅铝比进一步提高. X射线荧光散射光谱(XRF), ²⁷Al高分辨率魔角旋转固体核磁共振(MAS NMR), 红外(FT-IR)光谱等表征证明改性后的沸石骨架硅铝原子比分别为6.8和11.4. 低温氮吸附表明, 经盐酸处理的高硅STI沸石孔道开放完美, 但经氟硅酸铵处理的样品孔道被部分堵塞. 分段程序升温焙烧表明前者骨架热稳定性略差, 1000 ℃焙烧后结构基本被破坏, 而后者热稳定性较好, 经相同温度段焙烧后仍保持较高的结晶度和热稳定性, 其结构基本实现超稳化.     

CXN天然沸石的研究Ⅶ.骨架高硅超稳化改性

以高硅超稳化辉沸石(STI)为基底沸石,分别经盐酸脱铝或氟硅酸铵脱铝补硅处理后制备的改性H-STI沸石,其非骨架铝含量明显减少,而后者骨架硅铝比进一步提高.X射线荧光散射光谱(XRF),27Al高分辨率魔角旋转固体核磁共振(MAS NMR),红外(FT-IR)光谱等表征证明改性后的沸石骨架硅铝原子比分别为6.8和11.4.低温氮吸附表明,经盐酸处理的高硅STI沸石孔道开放完美,但经氟硅酸铵处理的样品孔道被部分堵塞.分段程序升温焙烧表明前者骨架热稳定性略差,1000℃焙烧后结构基本被破坏,而后者热稳定性较好,经相同温度段焙烧后仍保持较高的结晶度和热稳定性,其结构基本实现超稳化.     

CXN天然沸石的研究 V. 结构超稳化

以离子交换结合控制焙烧的方法分别制得结构超稳化高硅H-STI-I和H-STI-II沸石. EDX, ²⁹Si MAS NMR, ²⁷Al MAS NMR, FT-IR等表征证明, 其骨架硅铝原子比分别为4.43和10.62. 分段程序升温焙烧后的沸石样品经粉末XRD表征表明, 其结构热稳定性达到1000 ℃以上. 结构稳定化沸石呈现反映微孔特性的I型吸附等温线, 吸附孔道完美、开放. 经历过酸处理的H-STI-II沸石, 结构缺陷增多, 其热稳定性、比表面积及孔容积略低于H-STI-I.     

脱铝八面沸石的研究——Ⅲ.稳定性

以NaY沸石为原料,用SiCl_4同晶取代法制备了不同硅铝比且具有高结晶度的八面沸石,进一步将样品交换成铵型。还制备了超稳Y样品及铝交换型八面沸石。研究结果表明,随骨架硅铝比提高,八面沸石的骨架稳定性、热稳定性及水热稳定性均得到很大改善。骨架外铝会使较低硅铝比样品的水热稳定性变差。钠型及铵型样品在不同硅铝比时,对稳定性有不同影响。在骨架硅铝比相近情况下,SiC1_4脱铝沸石(DNH_4Y)较水热法脱铝沸石(USY)有好得多的热稳定性,然而二者却具有相近的水热稳定性。     

CXN天然沸石的研究 VI. 耐酸性及不同阳离子型沸石结构的热稳定性

以X射线粉末衍射(XRD)结晶度测定法观测CXN (STI型)天然沸石在不同浓度盐酸(HCl)热溶液中的结构耐酸性, 以及比较和研究用不同方法制备的结构超稳化高硅H-STI-I和H-STI-II沸石及其不同阳离子交换型M-STI (M＝Li, Na, K, Ca, Ag) 系列沸石在程序阶梯升温过程中的结构热稳定性. 用X射线荧光散射(XRF), ²⁹Si与²⁷Al固体核磁共振(MAS NMR)表征超稳化高硅H型沸石的组成与结构性质. 结果表明该天然沸石在浓度低于2 mol/L盐酸中可较长时间保持结构完美. 视阳离子类型不同, 经1173 K焙烧后M-STI-I系列沸石与M-STI-II系列沸石相对结晶度降低百分数分别为2.5%～18% 与0～35%. 在M-STI-I系列沸石中, 焙烧前后相对结晶度下降幅度的次序为K型＜(H, Li, Na)型＜(Ca, Ag)型, 而M-STI-II系列沸石, (Na, K)型＜(Li, H, Ca)型＜Ag型. 从沸石骨架硅铝比、结构缺陷、阳离子种类及其氧化物形成热等方面讨论影响沸石结构热稳定性的因素.     

天然CXN沸石分子筛水热稳定性研究 II. 水蒸汽处理温度对铵型沸石物化性质的影响

在前文研究天然Stilbite沸石(CXN沸石)水热稳定性影响因素的基础上, 以27Al与29Si MAS NMR, NH3-TPD和低温氮吸附等详细研究了铵型CXN沸石骨架铝配位状态和硅配位状态, 表面酸性与孔性质等与水蒸汽处理温度的关系. 随温度升高, 沸石骨架硅铝比逐渐提高, 并伴随硅羟基缺陷增多. 经750 ℃水蒸汽处理3 h后沸石骨架硅铝比可达到21.3. 沸石总酸量随水蒸汽处理温度的提高而降低, 沸石骨架铝脱除造成沸石孔道部分被堵塞, 但同时形成有利于分子扩散的介孔.     

β-沸石骨架铝化改性的红外光谱

β沸石是以有机胺为模板剂合成的高硅沸石．为在孔道中进行吸附和催化反应,通常是在空气中 (５５０℃ )进行焙烧,将有机胺脱除并使质子酸中心形成．但这种脱模板剂方法,会造成骨架脱铝［１ -４］,使质子酸中心显著减少．β沸石固有结构中存在着孔道位错和结构空穴,空气中焙烧脱有机胺可能会进一步损伤沸石的骨架结构［４,５］．沸石骨架改性已发展了多种铝化方法［６ -８］．有的研究工作表明,通常用红外光谱和ＭＡＳＮＭＲ表征的非骨架铝,在温和的条件下,例如回馏温度下的离子交换或者在较低温度下 (１００℃或室温 )与碱反应就可…     

CXN天然沸石的研究 VI. 耐酸性及不同阳离子型沸石结构的热稳定性

以X射线粉末衍射(XRD)结晶度测定法观测CXN (STI型)天然沸石在不同浓度盐酸(HCl)热溶液中的结构耐酸性, 以及比较和研究用不同方法制备的结构超稳化高硅H-STI-I和H-STI-II沸石及其不同阳离子交换型M-STI (M＝Li, Na, K, Ca, Ag) 系列沸石在程序阶梯升温过程中的结构热稳定性. 用X射线荧光散射(XRF), ²⁹Si与²⁷Al固体核磁共振(MAS NMR)表征超稳化高硅H型沸石的组成与结构性质. 结果表明该天然沸石在浓度低于2 mol/L盐酸中可较长时间保持结构完美. 视阳离子类型不同, 经1173 K焙烧后M-STI-I系列沸石与M-STI-II系列沸石相对结晶度降低百分数分别为2.5%～18% 与0～35%. 在M-STI-I系列沸石中, 焙烧前后相对结晶度下降幅度的次序为K型＜(H, Li, Na)型＜(Ca, Ag)型, 而M-STI-II系列沸石, (Na, K)型＜(Li, H, Ca)型＜Ag型. 从沸石骨架硅铝比、结构缺陷、阳离子种类及其氧化物形成热等方面讨论影响沸石结构热稳定性的因素.     

超细NaY分子筛的深度脱铝

通过优化和组合不同脱铝补硅方法,依次经氟硅酸铵处理、600oC水热处理、硅溶胶+草酸处理和800oC水热处理过程,成功实现了200nm超细NaY分子筛的深度脱铝,最终产品骨架硅铝比高达27.3,比表面积为581.9m2/g,分子筛结晶度保持在65%以上.结果表明,对于超细NaY分子筛脱铝,第一步采用氟硅酸铵进行部分缺陷修补尤为重要.根据分子筛晶粒尺寸不同,需严格控制氟硅酸铵用量和处理次数.当晶粒为200nm时,氟硅酸铵与分子筛骨架铝的摩尔比为0.16,处理一次较为适宜.在连续脱铝过程中及时补修脱铝产生的缺陷是保障超细NaY分子筛成功脱铝的关键,而采用氟硅酸铵、硅溶胶、800oC高温水热处理,可有效实施这种骨架修正作用.     

天然CXN沸石分子筛水热稳定性研究 I. 水热稳定性影响因素

以天然CXN沸石为基底材料, 通过离子交换、焙烧和酸处理等方法研究了影响该沸石水热稳定性的因素. XRD, XRF和27Al MAS NMR等结果表明阳离子种类和位置均会影响沸石水热稳定性, 其中铵型CXN沸石的水热稳定性最高. 高温焙烧铵型CXN沸石虽能提高骨架硅铝比, 但骨架缺陷增多导致其水热稳定性下降. 还研究了水蒸汽量、处理温度和时间对沸石骨架结构变化的影响, 结果表明提高温度和水蒸汽量均会降低沸石结晶度, 但处理时间则对结晶度的影响较小.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.