SrTi0.9M0.1O3-δ钙钛矿型氧化物催化剂甲烷氧化偶联反应性能的研究

The structure and catalytic properties of SrTi_0.9M_0.1O_3-δ (M=Mg，Al， Zr) perovskite-type catalysts for ox-idative coupling of methane (OCM) have been studied by using X-ray diffraction (XRD)，X-ray photoelectron spectroscopy (XPS) and temperature-programmed desorption of oxygen(O₂-TPD) methods. It has been shown that doping the cations of lower valence (e.g. Mg²⁺， Al³⁺) to the B site of SrTi_0.9M_0.1O_3-δ perovskite-type catalysts results in the higher content of adsorbed oxygen species on the surface of catalysts and thus higher C₂-selectivity for OCM reaction. It is suggested that the oxygen vacancies of SrTi_0.9M_0.1O_3-δ (M=Mg， Al， Zr) perovskite-type catalysts are the sites responsible for oxygen activation， and the adsorbed oxygen species on the surface of SrTi_0.9M_0.1O_3-δ catalysts are the main active species for OCM reaction.     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

纳米Ce1-xLaxO2-δ的微波引诱燃烧合成及其性能表征

Nanometer Ce_1-xLa_xO_2-δ solid solutions were synthesized by microwave-induced combustion process us-ing cerium nitrate hexahydrate， lanthanum nitrate hexahydrate and urea as raw materials. The process took only six minutes to obtain La₂O₃-doped CeO₂ nanopowders. The nanopowders were characterized by XRD， Laser Raman spectrum ， UV-Vis spectroscopy，field-emission scanning electron micrograph(FE-SEM)and TEM. The results revealed that the grain size of Ce_1-xLa_xO_2-δ varied from 20 to 40 nm calculated by Scherer formula through the plane of (111)， that oxygen vacancy was produced in the crystal lattices and the concentration of oxygen vacancy was increased with La doping， therefore the covalence of Ce-O bond was strenthened， which results in more intensive UV-C(200～280 nm)absorption. It can be seen from SEM that the porous appearance was obtained. Grain size is no more than 40nm observed from TEM.     

Ca2-3xLa8+2x□x(SiO4)6O2的合成及其导电性能的研究

The silicate oxyapatites Ca_2-3xLa_8+2x□_x(SiO₄)₆O₂(x=0, 0.17, 0.33, 0.50, 0.67) was synthesized via a sol-gel method at low temperature. The apatite phases have been characterised by X-ray diffraction (XRD), conducting properties was studied by electrical chemistry impedance spectroscopy (EIS). The conductivity of La_9.33□_0.67(SiO₄)₆O₂ is 1.58×10^-3 S·cm^-1 at 700 ℃, it is higher about 4 270 times than that of Ca₂La₈(SiO₄)₆O₂, the activation energy is decreasing from 1.37 eV to 0.84 eV. With cation vacancies increasing,the conducting mechanism is gradually translation from a direct linear pathway free oxygen ion conduction to a curve pathway interstitial oxygen ion conduction. The electrical conductivities is almost independent of the oxygen partial pressure, this suggests that the oxyapatites exhibited almost pure O^2- ion conduction over a wide range of oxygen partial pressure.     

掺镍型层状LixNiyMn1-yO2正极材料的合成与电性能研究

A kind of cathode material of layered Li_xNi_yMn_1-yO₂ characterized with the O2 type has been synthesized by a simple method. Its precursor Na_xNi_yMn_1-yO₂ has been prepared from manganese dioxide， nickel hydroxide and sodium carbonate at high temperature in air and quickly cooled in cold water， then it has been exchanged by the melted LiNO₃ at 300～400℃ in air. The effects of calcine-temperature for the precursors and its compositions (the content of Na and Ni) on the electrochemical properties of the material Li_xNi_yMn_1-yO₂ have been investingated by XRD and electrochemical tests. The results show that the sample Li_0.7Ni_0.3Mn_0.7O₂， has the best electrochemical properties which shows only one charge-discharge potential stage of 2.8～3.0V and has a high specific capacity over 180mAh·g^-1 cycled between 2.0～4.20V. A significant structure transformation to the spinal-type phase has not been found in the charge-discharge cycling and the discharge specific capacity around 165mAh·g^-1 has re-mained after the 20th cyclings for the material.     

LiNi1-xMxVO4的红外光谱和拉曼光谱研究

The vanadates of LiNi_1-xM_xVO₄(M=Fe,Co,Ni) containing VO₄ tetrahedrons were synthesized by soft chemical method through a new mild liquid route. The samples sintered at 450℃ for 3h and at 650℃ for 3h are named for LT-LiNiVO₄ and for MT-LiNi_1-xM_xVO₄ respectively. All of the products were measured by X-ray diffraction, IR and Raman spectra respectively. In comparison with IR spectra of V₂O₅ and NiO, the LT-LiNiVO₄ has a strong and broad IR absorption band of VO₄ tetrahedrons located at 600～850cm^-1 with three small splitting peaks corresponding to the asymmetry stretching vibrations of V-O bonds. The results of IR and Raman spectra for MT-LiNi_1-xM_xVO₄ show that the cations of Ni²⁺, Co²⁺, Fe²⁺ have the influences on the frequency shifts of the V-O vibrations.     

Cu1-xAgxI(x=0.5～0.6)纳米微粒的制备与表征

In the presence of PVPK30,Cu_1-xAg_xI nanoparticles were prepared by ion exchange reaction.The product was characterized by FT-IR,XRD,TEM,EDS and SPS,respectively.It was found that the value of x is ap-proximately 0.5～0.6and the average diameter of the nanoparticles is 10～20nm.The product shows surface photovoltage property of semiconductor and the existence of Cu⁺ greatly enhances the separation efficiency of photoinduced electron-hole pairs.Meanwhile,SPS of Cu_1-xAg_xI nanoparticles with different X (Ag/I)value had been investigated. The results show that when X is 0.5～0.576, the SPS intensity of Cu_1-xAg_xI nanoparticles is highest.     

锂离子电池正极材料LiNi1-xCoxO2的合成及电化学性能研究

LiNi_1-xCo_xO₂ cathode materials for lithium ion batteries were synthesized by the co-precipitation and solid-state reaction methods with LiOH·H₂O, Ni(NO₃)₂·6H₂O and Co(NO₃)₂·6H₂O as raw materials. The materials were characterized by XRD, SEM and electrochemical tests. The results showed that synthesized cathode materials were with layered structure similar to α-NaFeO₂ and uniform morphology and nearly normal grain size distribution and better electrochemical performance when x was 0.18. The first charge and discharge capacity of the cathode material was 224.3 mAh·g^-1 and 194.2 mAh·g^-1, respectively. 88.5% of the first discharge capacity remained at the 20th cycle.     

CrOx/ SBA-15介孔催化剂上丙烷在二氧化碳气氛中脱氢反应的研究

The structure and catalytic properties based on Chromium Oxide supported on mesoporous SBA-15 for oxidative dehydrogenation of propane by CO₂ have been studied by using X-ray diffraction (XRD), ultraviolet-visible diffuse reflectance spectra (UV-Vis DRS), electron spin resonance (ESR), X-ray photoelectron spectroscopy (XPS) and propane pulsing experiments in the absence of gas-phase O₂. It has been shown that propane conversion and propene yield increase with Cr loadings. The propane conversion and propene yield on CrO_x(Cr: 10wt%)/SBA-15 catalyst for oxidative dehydrogenation of propane by CO₂ at 550 ℃ reach 24.8% and 21.8%, respectively .The results of ESR, UV-Vis DRS and propane pulsing experiments indicate that Cr^Ⅲ in the CrO_x/ SBA-15 catalyst is the main active species in oxidative dehydrogenation of propane by CO₂ and Cr^Ⅵ, Cr^Ⅴ is inactive in dehydrogenation.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

[Na(DB18C6)(CH3CN)]2Mo6O19的合成、晶体结构及谱学表征

A novel super-molecular complex, [Na(DB18C6)(CH₃CN)]₂Mo₆O₁₉, was obtained by solvothermal reaction and characterized by elementary analysis, IR, ¹H NMR, gumbc spectrum and X-Ray diffraction experiment. The compound crystallizes in monoclinic space group P2₁/n with a=1.187 1(3) nm, b=2.096 3(6) nm, c=1.415 8(4) nm, β=110.854(5)° and Z=4. The complex contains four basic units: Na⁺, CH₃CN, DB₁₈C₆和Mo₆O₁₉^2-. Sodium ions located in the cavity of dibenzo-18-crown-6 with 6 Na-O bonds and the crown ether-sodium ion complex is supported on the terminal oxygen atoms of the typical Lindqvist isopolyanion Mo₆O₁₉^2- via the coordinative interactions. Mo₆O₁₉^2- located between two DB₁₈C₆ and led to the formation of the “hamburger” structure. The crystal is stabilized by van der waals force and interaction of π-π system. CCDC: 272936.     

多元掺杂尖晶石型Li1.02MxMn2-xQyO4-y正极材料的电化学特性

The effect of doping on the electrochemical performance was studied for spinel type Li_1.02M_xMn_2-xQ_yO_4-y used as cathode material in lithium-ion battery. TG/DTA curves of the precursor(the raw materials) doped with different elements were studied. The spinel materials Li_1.02Mn₂O₄, Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98, Li_1.02Co_0.02Cr_0.01 La_0.01Mn_1.96Cl_0.02O_3.98, Li_1.02Co_0.02La_1.02Mn_1.97Cl_0.02O_3.98, Li_1.02Co_0.02Cr_0.01Mn_1.97O₄, were prepared by solid-state reaction method after the pretreatment of conversion under low temperature and uniform mixing. X-ray diffraction patterns showed that all the samples had perfect spinel structure. SEM indicated that the particles of the samples had uniform size and were distributed evenly. The results of the charge/discharge curves showed that Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98 had better performance than other materials according to the inhibition of decline of reversible capacity of spinel Li_1.02M_xMn_2-xQ_yO_4-y. Therefore, cycle performance had been improved so obviously that 93.9% of the initial capacity were preserved after 100 cycles. Furthermore, electrochemical impedance tests were carried out with the spinel Li_1.02Co_0.02Cr_0.01La_0.01Mn_1.96F_0.02O_3.98 as working electrode, Lithium as counter electrode and reference electrode. Results showed that this material possessed good charge/discharge reversible capability and had the lowest impedance in 3.95～4.25 V range (on the stage of charge / discharge).     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

掺钇锆酸锶-TiO2复合光催化剂的制备及性能研究

SrZrO₃ particles were prepared by a co-precipitation method and Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles were then synthesized by Sr(Zr_1-xY_x)O_3-δ and titanium dioxide. The composite particles were characterized by XRD, SEM, FTIR and TG-DTA techniques. The photocatalytic degradation of methylene blue (MB) in aqueous solution was used as a probe reaction to evaluate the photocatalytic activity of the composite particles. The effect of the preparation method for SrZrO₃, doping content of yttrium and TiO₂ amount in the composite particles on the photocatalytic activity of composite particles was also discussed. The results show that the methylene blue solution could be completely degraded by Sr(Zr_1-xY_x)O_3-δ -TiO₂ composite particles under UV-light or visible light irradiation. The photocatalytic activity of composite particles was higher than that of pure TiO₂. The fast recombination of photogenerated electrons and holes were restrained by the heterojunction formed in composite particles. The particle of SrZrO₃ prepared by co-precipitation was small, and the photocatalytic activity of composite particles prepared from this kind of SrZrO₃ was higher than that of particles prepared by solid sintering method. The best doping content of yttrium is 5%. The optimal content of TiO₂ in composite particles is 90wt%, 70wt%, respectively under UV-light and visible light irradiation, the degradation rates of MB are 98.8% and 93.5% , respectively after 50 min irradiation.     

BaxCe0.8Y0.2O3-α固体电解质的氧离子导电性

Ba_xCe_0.8Y_0.2O_3-α(x=1.03，1，0.98) solid electrolyte samples show a single phase of orthorhombic perovskite of BaCeO₃. The oxide-ion conduction and transport number were detected in the temperature of 600～1000℃ by electrochemical oxygen permeation (oxygen pumping)， and compared with the results from the oxygen concentration cell. The relation between the ingredient of Ba and oxide-ion conduction was also researched. It was found that these electrolytes exhibited the mixed oxide-ionic and electronic hole conduction under the experimental temperature and oxygen gas. The oxide-ion transport numbers are 0.1～0.6， which are close to the results of the oxygen con-centration cell. They increase as the decrease of Ba content in the samples.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

Mn位掺杂钙钛矿结构化合物LaSr2Mn2-xNixO7的磁性和电性的研究

The effect of Ni substitution for Mn on magnetic and transport properties has been investigated for layered manganese oxides LaSr₂Mn_2-xNi_xO₇. Nickel doping hampered the canted antiferromagnetic (AFM) exchange at low temperature and their Neel temperature (T_N) decreased from 138 K (x=0) to 102 K (x=0.3). Meanwhile, spin glass, charge ordering and metal-insulator transition are suppressed by Ni addition. The resistivity increases obviously with increasing x due to double exchange interaction channel broken by Ni²⁺ addition. The resistivity of all samples in low temperature range fits to the Mott′s variable rang hopping (VRH) model, while it fits to nearest neighbor hopping of small polarons model in high temperature range.     

固体电解质La2-xCaxMo1.7W0.3O9-δ(0≤x≤0.2)的合成、表征及电性能

在氧离子导体La₂Mo_1.7W_0.3O₉的基础上，采用固相法合成了La位掺杂的Ca系列新型氧化物La_2-xCa_xMo_1.7W_0.3O_9-δ(0≤x≤0.2)。通过XRD、Raman和XPS等手段对化合物结构进行表征，交流阻抗谱测试其电性能。结果表明：掺杂离子Ca²⁺的半径小于基质离子La³⁺的半径导致晶格收缩；Ca的掺杂在La₂Mo_1.7W_0.3O₉自身内置氧空位的基础上增加了额外的氧空位，提高了氧离子导体的电导率，550 ℃电导率由0.79 × 10^-4 S·cm^-1 (x=0.0)增加到1.5 × 10^-4 S·cm^-1 (x=0.16，0.2)，电导率增加89.9%。     

BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)的制备及性能研究

采用高温固相反应法制备了质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)。结合XRD、SEM、EIS等技术对其物相、微观形貌、稳定性及电导率进行了研究。结果表明,在1 600 ℃烧结5 h制备的质子导体BaCe_0.8-xNb_xGd_0.2O_3-δ(0≤x≤0.45)均能保持主相为斜方晶的钙钛矿结构。Nb的加入可明显提高烧结样品的致密性及在CO₂和水蒸气气氛下的稳定性。在湿润H₂/Ar(0.4%,V/V)气氛中800 ℃下,x=0.1样品的电导率为5.73 mS·cm^-1,电导活化能为0.35 eV,与x=0的样品相当。