聚苯胺/Co_(0.5)Zn_(0.5)Fe_2O_4纳米复合材料的制备及电磁性能

采用高分子凝胶法制备尖晶石型Co0.5Zn0.5Fe2O4,原位聚合法制备纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4纳米复合材料.使用傅立叶红外光谱(FTIR)、紫外可见吸收光谱(UV-Vis)、X射线衍射仪(XRD)和透射电子显微镜(TEM)对复合材料进行了表征.FTIR和XRD的结果表明样品为纯聚苯胺和聚苯胺/Co0.5Zn0.5-Fe2O4.UV-Vis光谱表明聚苯胺/Co0.5Zn0.5Fe2O4苯环上的π-π*和n-π*分别红移了23nm和5nm.TEM照片可知,聚苯胺和聚苯胺/Co0.5Zn0.5Fe2O4粒子的平均粒径分别约为50nm和70nm.在8.2～12.4GHz测试频率范围内,聚苯胺/Co0.5Zn0.5Fe2O4的ε″数值在9.2～12.3之间,u″数值在0.15～0.16之间;聚苯胺/Co0.5-Zn0.5Fe2O4介电损耗低于纯聚苯胺,而磁损耗高于纯聚苯胺.     

基于碳纳米管－聚苯胺纳米复合物的超级电容器研究

为了提高碳纳米管的比容, 采用化学原位聚合的方法在碳纳米管的表面包覆聚苯胺, 制备碳纳米管-聚苯胺纳米复合物. 运用TEM和IR对样品进行了表征. 通过循环伏安研究样品的电化学特性. 利用恒流充放电考察基于碳纳米管-聚苯胺复合物超级电容器的性能. 在相同实验条件下, 对碳纳米管进行了比较分析. 实验结果表明, 在电流密度为10 mA/cm²时, 碳纳米管和碳纳米管-聚苯胺复合物的比容分别为52和201 F/g. 基于碳纳米管-聚苯胺纳米复合物的超级电容器的能量密度达到6.97 Wh/kg, 并且具有良好的功率特性.     

银/碳纳米管纳米复合物制备及性质研究

基于苯环与碳纳米管之间较强的π-π共轭效应和醛基对银氨溶液的还原作用,利用吸附在碳纳米管上的香草醛分子原位还原[Ag(NH3)2]+,成功获得了纳米银/碳纳米管(Ag-NPs/CNTs)复合纳米材料。紫外-可见吸收光谱和荧光光谱结果表明,碳纳米管对香草醛分子有较强的吸附作用及银纳米粒子的形成。透射电镜结果表明,碳纳米管表面形成了大小约5.0 nm银纳米颗粒。所制备的纳米复合材料表现出较明显的荧光特性,且对浓度为1.0×10-7～6.0×10-7 mol/L的H2O2表现出较好的电催化还原能力。     

金属卟啉有机共价和非共价修饰多壁碳纳米管

合成了5-(4-羟基苯基)-10,15,20-三苯基卟啉锌配合物, 与活化的多壁碳纳米管(MWNT)发生酯化反应, 从而得到金属卟啉有机共价化学修饰的多壁碳纳米管复合物; 利用金属卟啉环上的π电子与多壁碳纳米管管壁上的π电子通过π-π堆积效应, 得到金属卟啉有机非共价修饰的多壁碳纳米管复合物. 通过透射电镜(TEM)考察了金属卟啉-多壁碳纳米管复合物的形貌特征; 通过红外光谱对产物的化学结构进行了表征; 通过紫外光谱、荧光光谱和热失重分析(TGA)对比分析了两类复合物, 发现非共价修饰的金属卟啉-碳纳米管复合物的荧光淬灭率更高, 非共价修饰的金属卟啉-碳纳米管复合物中卟啉的含量比较高.     

金属卟啉化学共价和非共价修饰多壁碳纳米管

合成了5-(4-羟基苯基)-10,15,20-三苯基卟啉锌配合物,与活化的多壁碳纳米管(MWNT)发生酯化反应,从而得到金属卟啉有机共价化学修饰的多壁碳纳米管复合物;利用金属卟啉环上的π电子与多壁碳纳米管管壁上的π电子通过π-π堆积效应,得到金属卟啉有机非共价修饰的多壁碳纳米管复合物.通过透射电镜(TEM)考察了金属卟啉-多壁碳纳米管复合物的形貌特征;通过红外光谱对产物的化学结构进行了表征;通过紫外光谱、荧光光谱和热失重分析(TGA)对比分析了两类复合物,发现非共价修饰的金属卟啉-碳纳米管复合物的荧光淬灭率更高,非共价修饰的金属卟啉-碳纳米管复合物中卟啉的含量比较高.     

聚1,4-二氨基蒽醌/多壁碳纳米管复合物的制备及其电化学性质研究

以多壁碳纳米管为基板,运用简单磁力搅拌方法,通过π-π堆积作用,使1,4-二氨基蒽醌负载于多壁碳纳米管材料上,获得了聚氨基蒽醌/多壁碳纳米管复合物(PDAAQ/MWCNTs)。采用傅立叶红外光谱(FTIR)、透射电子显微镜(TEM)、循环伏安(CV)和恒流充放电(GCD)等方法对PDAAQ/MWCNTs的结构和性能进行表征。结果发现3~4 nm厚的聚氨基蒽醌层原位生长在多壁碳纳米管上,这种独特的结构极大地增加了复合物的比表面积和聚氨基蒽醌的利用率。分散性能好的PDAAQ/MWCNTs复合物具有高的赝容性能。     

用带不同侧链的双取代聚乙炔衍生物增溶多壁碳纳米管

采用不同的双取代聚乙炔与多壁碳纳米管复合,通过π-π相互作用和聚合物链缠绕实现了对碳纳米管的增溶.这种方法对碳纳米管的结构没有损害,而且包覆到碳纳米管表面的双取代聚乙炔也显示了自身的荧光发射特性.     

铂/酞菁/碳纳米管复合纳米催化剂的构建及其甲醇氧化性能

本文报道了一种方便地构建铂/酞菁/碳纳米管(Pt/Pc/CNTs)复合纳米催化剂的新方法：先通过简单的超声处理将酞菁分子(Pc)修饰至碳纳米管表面,随后采用乙二醇还原法将铂纳米粒子固载到酞菁修饰的碳纳米管表面,形成Pt/Pc/CNTs复合纳米催化剂。X射线衍射(XRD)和透射电镜(TEM)结果表明金属铂纳米颗粒均匀地分散在碳纳米管表面,尺寸约5 nm。采用UV-Vis、FTIR和Raman等手段研究了这种复合纳米催化剂的构建过程,结果表明酞菁分子与碳纳米管之间存在较强的π-π相互作用,使其能牢固地吸附于碳     

聚苯胺共价接枝碳纳米管复合材料的制备及其超电容性能的研究

以氨基化的碳纳米管为基体, 通过低温原位聚合的方法将聚苯胺共价接枝于碳纳米管表面, 通过透射电镜(TEM)、X射线衍射(XRD)、紫外可见光(UV-vis)、傅里叶红外(FT-IR)、拉曼(Raman)及电化学方法对复合材料进行了表征. 结果表明通过低温原位聚合的方法可以使聚苯胺均匀接枝于碳纳米管表面. 电化学测试结果表明, 碳纳米管共价接枝聚苯胺作为超级电容器材料在0.5 A/g条件下聚苯胺的电容贡献值为754.8 F/g, 同时其倍率性能以及循环稳定性方面都明显优于聚苯胺非共价修饰的碳纳米管复合材料.     

非共价键法改性碳纳米管的研究进展

阐述了非共价键改性在碳纳米管功能化方面的应用进展,详细介绍了表面活性剂修饰、小分子的π-π堆积相互作用、聚合物的缠绕和包覆、生物大分子的包裹和吸附、内嵌填充修饰等改性方式的研究现状,并提出了非共价键法修饰碳纳米管未来改进的方向,探讨了不同修饰物与碳纳米管之间的相互作用机制。其中,含有共轭基团或芳基基团的聚合物,可以通过其共轭或芳基基团与碳纳米管间的π-π相互作用和范德华作用,实现对碳纳米管的非共价物理包覆。经聚合物功能化的碳纳米管在电池、催化剂、生物传感器和电化学装置上有较好的应用前景。此外,生物大分子对碳纳米管的非共价修饰不仅可以改善其在生物体系中的水溶性,而且通过合理设计还可以避免蛋白质、核酸等生物分子的非特异性吸附,从而得到具有特异性的生物分子-碳纳米管复合体系。     

Influence of silver-decorated multi-walled carbon nanotubes on electrochemical performance of polyaniline-based electrodes

In this work, silver (Ag) nanoparticles were deposited on multi-walled carbon nanotubes (MWNTs) by chemical reduction while Ag-decorated MWNTs (Ag-MWNTs)/polyaniline (PANI) composites were prepared by oxidation polymerization. The effect of the Ag incorporated into the interface of the composites on the electrochemical performance of the MWNTs/PANI was investigated. It was found that highly dispersed Ag nanoparticles were deposited onto the MWNTs, and the Ag-MWNTs were successfully coated by PANI. According to cyclic voltammograms, the Ag-MWNTs/PANI exhibited significantly increased electrochemical performances compared to MWNTs/PANI and the highest specific capacitance obtained of MWNTs/PANI and 0.15 M Ag-MWNTs/PANI was 162 F/g and 205 F/g, respectively. This indicated that Ag nanoparticles that were deposited onto the MWNTs caused an enhanced electrochemical performance of the MWNTs/PANI due to their high electric conductivity, which resulted in an increase of the charge transfer between the MWNTs and PANI by a bridge effect.     

有机化学接枝-电化学沉积聚合制备CNTs/PANI纳米复合材料

通过有机化学合成法先在碳纳米管表面接枝上苯胺单体,然后在不锈钢电极表面在硫酸溶液中采用循环伏安法电化学沉积聚合制得碳纳米管/聚苯胺(CNTs/PANI)纳米复合材料.扫描电子显微镜和傅立叶变换红外光谱表征所得材料的微观结构和基团,循环伏安和恒流充放电测试用于考察所得CNTs/PANI纳米复合材料的电化学性能.所得结果与...     

Facile preparation and enhanced capacitance of the polyaniline/sodium alginate nanofiber network for supercapacitors

A porous and mat-like polyaniline/sodium alginate (PANI/SA) composite with excellent electrochemical properties was polymerized in an aqueous solution with sodium sulfate as a template. Ultraviolet-visible spectra, X-ray diffraction pattern, and Fourier transform infrared spectra were employed to characterize the PANI/SA composite, indicating that the PANI/SA composite was successfully prepared. The PANI/SA nanofibers with uniform diameters from 50 to 100 nm can be observed on scanning electron microscopy. Cyclic voltammetry and galvanostatic charge/discharge tests were carried out to investigate the electrochemical properties. The PANI/SA nanostructure electrode exhibits an excellent specific capacitance as high as 2093 F g(-1), long cycle life, and fast reflect of oxidation/reduction on high current changes. The remarkable electrochemical characteristic is attributed to the nanostructured electrode materials, which generates a high electrode/electrolyte contact area and short path lengths for electronic transport and electrolyte ion. The approach is simple and can be easily extended to fabricate nanostructural composites for supercapacitor electrode materials.     

超级电容器用含氮碳与含氮碳/炭气凝胶复合电极材料的制备和性能研究

采用原位聚合法合成聚苯胺(PAIN)及聚苯胺/炭气凝胶(PAIN/CA)复合材料,经过高温裂解制备含氮碳(NC)及含氮碳/炭气凝胶复合材料(NC/CA),再以KOH为活化剂对其进行活化,制备活化含氮碳(ANC)及活化含氮碳/炭气凝胶复合材料(ANC/CA)。采用扫描电镜、循环伏安、恒流充放电以及电化学阻抗等方法进行性能测试,结果表明,由于KOH的活化作用,含氮碳材料的粒径明显变小,其比电容值为138 F/g,高于未活化含氮碳材料(98 F/g),ANC/AC3复合材料电极的比电容值比ACA电极(88 F/g)高,达到127 F/g。     

氧化剂对磺化石墨烯负载聚苯胺复合材料结构与电化学性能的影响

以磺化石墨烯(sGNS)为基板材料,通过界面聚合方法制备出不同分级结构磺化石墨烯负载聚苯胺(sGNS/PANI)复合材料,并系统研究了氧化剂类型对复合材料的化学组成、形貌结构和超级电容特性的影响.结果显示,过硫酸铵为氧化剂合成的复合材料中PANI的产率和氧化程度最高,其形貌呈现出sGNS垂直生长PANI纳米短棒阵列结构,PANI的共轭程度和结晶性均较高,从而赋予复合材料高的比电容(497.3 Fg-1),以及良好的倍率特性和循环稳定性(2000次循环后比电容仅损失5.7%).当以三氯化铁为氧化剂时,复合材料中PANI的得率很低,并在sGNS表面形成较薄的包覆层,此时复合材料的比电容最低(228.5 Fg-1),但充放电循环性能较好(2000次循环后比电容的保持率为87.4%).当氧化剂为高锰酸钾时,复合材料中PANI以团聚态颗粒无规堆积在sGNS表面,PANI以无定型结构存在,其比电容虽然较高(419.6 F g-1),但其倍率特性和充放电循环性能较差(2000次循环后比电容损失19.9%).     

电化学阴极沉积制备氧化镍/碳纳米管复合电极的准电容特性

A novel type of composite electrode based on multiwalled carbon nanotubes coated with nano nickel oxide particles has been used in supercapacitors. Nickel oxide cathodically deposited from Ni(NO3)2 solution with carbon nanotubes as the matrix exhibited large pseudocapacitance of 25F/g in 6 mol/L KOH. The morphology of composites was examined by scanning electron microscope (SEM). To characterize the CNTs/nickel oxide composite electrode, a charge discharge cycling test for measuring specific capacitance, cyclic voltammetry, and ac impedance test is executed. The nickel oxide composite exhibiting excellent pseudocapacitive behavior(i.e.high reversibility, high specific capacitance, and low self discharge rate) has been demonstrated to be a potential candidate for the application of electrochemical supercapacitors.     

Facile synthesis of multifunctional multiwalled carbon nanotubes/Fe3O4 nanoparticles/polyaniline composite nanotubes

With an average diameter of 100-150 nm, composite nanotubes of polyaniline (PANI)/multiwalled carbon nanotubes (MWNTs) containing Fe₃O₄ nanoparticles (NPs) were synthesized by a two-step method. First, we synthesized monodispersed Fe₃O₄ NPs (d=17.6 nm, σ=1.92 nm) on the surface of MWNTs and then decorated the nanocomposites with a PANI layer via a self-assembly method. SEM and TEM images indicated that the obtained samples had the morphologies of nanotubes. The molecular structure and composition of MWNTs/Fe₃O₄ NPs/PANI nanotubes were characterized by Fourier transform infrared spectra (FTIR), energy dispersive X-ray spectrometry (EDX), X-ray photoelectron spectra (XPS), X-ray diffraction (XRD) and Raman spectra. UV-vis spectra confirmed the existence of PANI and its response to acid and alkali. As a multifunctional material, the conductivity and magnetic properties of MWNTs/Fe₃O₄ NPs/PANI composites nanotubes were also investigated.     

The Electrochemical Properties of Nanocomposite Films Obtained by Chemical In Situ Polymerization of Aniline and Carbon Nanostructures

Interactions between the π bonds in the aromatic rings of polyaniline (PANI) with carbon nanostructures (CNs) facilitate charge transfer between the two components. Different types of phenyleneamine‐terminated CNs, including carbon nano‐onions (CNOs) and single‐walled and multi‐walled carbon nanotubes (SWNTs and MWNTs, respectively), were prepared as templates, and the CN/PANI nanocomposites were easily prepared with uniform core–shell structures. By varying the ratio of the aniline monomers relative to the CNs in the in situ chemical polymerization process, the thickness of the PANI layers was effectively controlled. The morphological and electrical properties of the nanocomposite were determined and compared. The thickness and structure of the PANI films on the CNs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and infrared spectroscopy. TEM and SEM revealed that the composite films consisted of nanoporous networks of CNs coated with polymeric aniline. The electrochemical properties of the composites were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. These studies showed that the CN/PANI composite films had lower resistance than pure polymeric films of PANI, and the presence of CNs much improved the mechanical stability. The specific electrochemical capacitance of the CNO/PANI composite films was significantly larger than for pure PANI.     

Nickel oxide coated on ultrasonically pretreated carbon nanotubes for supercapacitor

Nickel oxide/carbon nanotubes (NiO/CNTs) composite materials for supercapacitor are prepared by chemically depositing nickel hydroxide onto carbon nanotubes pretreated by ultrasonication and followed by thermal annealing at 300 °C. A series of NiO/CNTs composites with different weight ratios of nickel oxide versus carbon nanotubes are synthesized via the same route. The high-resolution TEM and SEM results show that a lot of nicks, which favored the nucleation of the nickel hydroxide formed on the outer walls of carbon nanotubes due to ultrasonic cavitations, and then nickel oxide coated uniformly on the outer surface of the individual carbon nanotubes. The NiO/CNTs electrode presents a maximum specific capacitance of 523 F/g as well as a good cycle life during 1,000 cycles in 6 M KOH electrolyte. The good electrochemical characteristics of NiO/CNTs composite can be attributed to the three-dimensionally interconnected nanotubular structure with a thin film of electroactive materials.     

Preparation of hierarchical polyaniline nanotubes based on self‐assembly and its electrochemical capacitance

This article reports the preparation and self‐assembly of polyaniline (PANI) nanotubes, which were chemically synthesized by using in situ doping polymerization in the presence of ammonium persulfate (APS; (NH₄)S₂O₈) as the oxidant without the use of an external template. The synthesized hierarchically nanotubes with a shape of a single nanotube with a length of 0.6 to 0.8 µm and an average with of 100 nm assembled from nanoparticles. The effects of the [salicylic acid]/[aniline] ratio on the size and capacitance of PANI nanotubes were studied. The specific capacitance behavior of the PANI nanotubes was also investigated by using cyclic voltammogram and galvanostatic charge–discharge tests. A maximum discharge‐specific capacitance of 422.5 F/g could be achieved, suggesting its potential application in electrode material for electrochemical capacitors. Copyright © 2011 John Wiley & Sons, Ltd.