PREPARATION AND PROPERTIES OF EPOXY RESIN MODIFIED BY LIQUID CHLOROPRENE-HYDROXYETHYLMETHACRYLATE COPOLYMER

The epoxy resin modified by liquid chloroprene-hydroxyethylmethacrylate copolymer (CP-HEMA) is a new kind of structural adhesives with good mechanical properties. By changing its mole-cular structure, it may also have such desirable properties as retardation of combustion, enduringweather aging, inert oils and chemicals. A series of the thermosets of the epoxy resin modifiedby CP-HEMA used as a toughener were prepared. The effects of CP-HEMA content, catalyst con-tent and curing temperature on the mechanical properties of modified epoxy resin system were studied.The thermal weight-loss curves were examined. The two-phase morphology was observed and dis-cussed.     

The effect of polymerization conditions on crystalline of polybutene-1 catalyzed by metallocene catalyst

Polybutene-1 was synthesized stereoselectively with the precursorη5-(pentamethyl-cyclopentadienyl) tribenzyloxide titanium (Cp*Ti(OBz)3) and methylaluminoxane (MAO). The effects of polymerization conditions, trimethyl alumina (TMA) content in MAO and temperature on the crystalline and molecular weight of the products, and catalytic activity were investigated. The structural properties of the polybutene-1 were characterized with 13C NMR and WAXD.     

氧化镁在不同养护条件下水化产物的形貌分析

The morphologies of brucite formed from MgO hydration under different curing conditions were studied. The results showed that there were relations between the morphologies of brucite and its forming conditions. The size of brucite crystals increased with the curing time, and they were fiber-shaped at lower curing temperature and stick-shaped at higher temperature. When MgO was cured in paste with 10 percent cement, the crystal of brucite was fiber-shaped, while cured in paste with 95 percent cement, the crystal was hexaflaggy-shaped, which aggregated and produced some micro-cracks in paste when the curing temperature was increased. At 180 ℃ autoclaving temperature of MgO, the brucite was regular hexaflaggy-shaped crystal; for 216 ℃, it was less irregular. When the paste mixed with 50 percent fly ash, the crystal of brucite was needle-shaped and distributed more evenly, so decreased the deformation and crack of the concrete.     

Effect of operating conditions and potassium content on Fischer-Tropsch liquid products produced by potassium-promoted iron catalysts

The dependencies of Fischer-Tropsch synthesis liquid hydrocarbon product distribution on operating pressure and temperature have been studied over three potassium-promoted iron catalysts with increasing potassium molar content. The study followed an experimental planning and the results were analyzed based on surface response methodology. The effects of different operating conditions and potassium contents on the liquid product distribution were compared based on number average carbon number and dispersion. Results showed that high pressures （25 to 30 arm） favored the production of waxes that could be converted into liquid fuels through hydrocracking, while greater direct selectivity towards diesel was favored by low pressure （20 arm） using catalysts with low potassium to iron molar ratios. The liquid product distribution produced using an iron catalyst with high potassium content presented higher number-average number of carbons when compared to the distribution obtained using an iron catalyst with low potassium content.     

A Study on the Structure and Behavior of Sinter-free Material for Phosphorous Removal from Waste Water

Oyster shell and cement were taken as the major raw materials to fabricate hollow, tubular and recoverable material for phosphorous removal (P removal) from waste water without sintering. In this paper, the effects of different affecting factors on the sample P removal ratio were discussed to select optimal P removal process conditions. SEM and XRD were used to characterize the microscopic structures and composition of samples, and molybdenum blue spectrophotometry was applied to determine the P content in waste water. Results showed that at 30 ℃ for 2 d, the P removal ratio reached 93.3% when the cement content was 10 wt% and oyster shell powder was 90 wt%. SEM analysis revealed a flaky structure consisting of phosphorus-containing compound in the samples after P removal, and it piled on and maintained the porous structure. In addition, the results also suggested that raising the ambient temperature was benefit to the P removal. The P removal ratio of the material was optimal under neutral and alkali conditions.     

Synthesis and Properties of Aryloxy—terminated Polydimethylsiloxanes

Aryloxy-terminated polydimethylsiloxanes (AOS) were synthesized by the telomerization of hexamethylcyclotrisiloxane(D3) with phenols.The structures of AOS were characterized by UV,IR,^2HNMR and elemental analysis,The effects of the reaction conditions and the mole ratios of the reactants on the molecular weight of the polymer were discussed.AOS′s structural influence on bactericidal action,flocculation and hydrolysis was studied.     

Study on the Structures and Properties of Copper Removal Adsorbent Prepared from Sinter-free Pulverized Oyster Shell Materials

A hollow tubular copper removal adsorbent was prepared with oyster shell and cement as the main raw materials. The effects of different formulas, different initial copper concentrations and different pH values of samples on the copper removal efficiency were investigated to determine the optimal conditions for copper removal. The content of copper in the wastewater is determined by Atomic Absorption Spectrophotometer. The microstructure and elemental composition of the samples were characterized by scanning electron microscopy(SEM) and EDS. As a result, the formula with the content of cement to be 8 wt% and the oyster shell powder of 92 wt% is optimal. Under the condition of 30 ℃, when the pH value was 9.0, the Cu2+ adsorption capacity of the sample could reach 0.59 mg/g at 48 h. SEM analysis revealed that there are abundant pores in the sample, which is beneficial for Cu2+ absorption on the adsorbent.     

乳化剂在双重乳液合成含胰岛素纳米胶囊中的作用

Insulin entrapped nanocapsules to use polylactide （PLA） as the encapsulating material were prepared through a modified water-in-oil-in-water （W/O/W） emulsification and solvent evaporation method, The average particle size of PLA nanocapsules obtained was decreased to （181.5 ± 8.4） nm, and capably adjusted from 180 to 370 nm by using different types and content of nonionic emulsifiers. The influence of emulsifiers on property of nanocapsules was discussed in detail. The effects of spans and tweens to modify the size of the nanocapsules were different, which can be due to the distribution of the surfactants on the inner interface between the inner water and oil of the double emulsion. The encapsulation efficiency and drug release of nanocapsules were affected obviously by the content and type of emulsifiers.     

GRAFT COPOLYMERIZATION OF ACRYLAMIDE ONTO POLYPROPYLENE FILMS BY PLASMA TECHNIQUE

The graft copolymerization of acrylamide onto polypropylene (PP) Film was carried out by using a capacitively coupled rf plasma apparatus with external plate electrodes. The relationship between the surface structure of the Ar plasma-treated PP films and the extent of grafting of acrylamide on the films was studied through observing the effects of discharge power and exposure time on the relative content of free-radical on the film surface. Meanwhile, the wettability and surface energy of the PP film were measured.     

A New Method of Separation of Four Benzodiazepines by RP-CEC

A new method to separate diazepam, nitrazepam, estazolam, alprazolam was established on both C18 and C8 CEC columns. The influence of separation voltage, Tris concentration, column temperature and the percentage of acetonitrile on the resolution and retention behavior of four benzodiazepines was investigated. The results showed that the percentage of acetonitrile had the largest effect on the resolution and retention behavior of the four benzodiazepines. Other separation conditions had also effects on the resolution and retention behavior, but smaller than the concentration of acetonitrile. Optimum separation conditions were obtained to separate four benzodiazepines on C18 and C8 CEC columns.     

Propane Aromatization over Mo/HZSM-5 Catalysts

Impregnation, mechanical mixing and hydrothermal treatment methods were used to introduce molybdenum species into the HZSM-5 zeolite. The structure and surface acidity of the catalysts were studied by means of XRD, FT-IR, NH3-TPD, TPR and XPS. The effects of Mo content and reaction time on stream on the aromatization of propane were investigated. It was found that the performance of the Mo/HZSM-5 catalyst prepared by the hydrothermal treatment method was much better than that of the other two catalysts. For example, under the reaction conditions of 823 K and 600 h-1, propane conversion and aromatics selectivity over the catalyst prepared by hydrothermal pretreatment could reach 89.17% and 78.56%, respectively. XRD and XPS results showed that the Mo species in the catalysts prepared by hydrothermal treatment were highly dispersed on the surface of the HZSM-5, and larger amounts of them could penetrate into the HZSM-5 channel, as compared with the other two kinds of catalysts. These factors may be responsi     

Asymmetric reduction of α-hydroxy aromatic ketones to chiral aryl vicinal diols using carrot enzymes system

Asymmetric reduction ofα-hydroxy aromatic ketones was carried out by using carrot enzymes system,yielding corresponding chiral vicinal diols with special functional groups.The optimum reaction conditions were obtained after investigation of various influencing factors.Chiral aryl vicinal diols were produced with good yields and excellent enantiomeric excesses under appropriate conditions.Meanwhile,the steric factors and electronic effects of the substituents on the aromatic ring were shown to have an interesting influence on both yield and enantioselectivity.     

SYNTHESIS OF ALCOHOLS FROM HYDROGENATION OF CARBON DIOXIDE(Ⅲ)

The effects of catalyst preparation and reaction conditions on thecatalytic activity and selectivity for hydrogenation of carbon dioxide to alcoholsover zeolite supported bimetal catalyst were studied.The results showed that:(1)ethanol easily formed on the zeolite with larger pores and methanol did onthat with smaller pores;(2)when pH value of the ion exchange solution was10,the activity reached the maximum;(3)the optimum Cu/Ru mole ratio was3;(4)the influence of reation conditions such as temperature,pressure andH_2/CO_2 mole ratio on the topic reaction was greater.     

Influence of seeds on the synthesis of TS-1 with inorganic materials

Summary TS-1 with relatively small crystal sizes (0.4-1.5 μm) was synthesized using inorganic sources of Ti and Si. The effects of conditions in the preparation of seeds on the synthesized zeolites were studied.     

Numerical analysis and experimental study of hydrogen production from dimethyl ether steam reforming

An experimental and theoretical study of steam reforming of dimethyl ether was carried out in a processor for fuel cell vehicles to explore the effect of temperature gradient and hydrogen content of the processor.A steady-state,laminar,two-dimensional axi-symmetric model was proposed to investigate the fluid flow,heat transfer and chemical reactions in the dimethyl ether steam reforming processor using porous medium approach.The numerical model was established with Star-CD program using SIMPLE algorithm and finite volume method.Experimental verification of the two-dimensional mathematical model was conducted.The numerical results coincided well with the experimental data.The effects of the parameters on the temperature gradient and hydrogen content of the processor were studied using the numerical model.     

STRUCTURE AND PROPERTIES OF COMPOSITE POLYURETHANE HOLLOW FIBER MEMBRANES

Composite polyurethane (PU)-SiO2 hollow fiber membranes were successfully prepared via optimizing the technique of dry-jet wet spinning, and their pressure-responsibilities were confirmed by the relationships of pure water fluxtransmembrane pressure (PWF-TP) for the first time. The origin for this phenomenon was analyzed on the basis of membrane structure and material characteristics. The effects of SiO2 content on the structure and properties of membrane were investigated. The experimental results indicated that SiO2 in membrane created a great many interfacial micro-voids and played an important role in pressure-responsibility, PWF and rejection of membrane: with the increase of SiO2 content, the ability of membrane recovery weakened, PWF increased, and rejection decreased slightly.     

Preparation, Curing Reactivity and Thermal Properties of Titanium-doped Silicone Resins

Novel titanium-doped silicone resins were synthesized from low-cost silane monomers and tetrabutyl titanate as raw materials and hydrochloric acid as catalyst, with titanium element as dopant into principal chain of Si-O-Si. The resins were characterized by means of FTIR, 1 H NMR and 13 C NMR spectra, their thermal properties and curing properties were investigated and their corresponding films were determined. The results show that the thermal stability and storage stability of the resins were influenced by the types of silane monomers containing different carbon atomicities of organic group. The thermal stability of the titanium-doped silicone resin with a molar ratio of silane monomer B(n-propyl triethoxysilane) to silane monomer C(n-octyl triethoxysilane) being 1:1 is superior to that of the resin with a molar ratio of silane monomer B to silane monomer C being 1:3. However, the storage stability of the former is inferior to that of the latter.This work also showed that the synthesized titanium-doped silicone resins have the highest thermal stability up to 450―500 °C with an atomicity molar ratio of 1:4 of titanium to silicon in the reactants. But the best storage stability of the resin prepared from the reactants with an atomicity molar ratio of 1:6[n(Ti):n(Si)] was obtained. The effect of the type and content of curing agent on the curing properties of the resin was also studied. Moreover, thermal mechanism and curing mechanism were proposed in this work.     

A STUDY ON THE DEGRADATION MECHANISM OF PHOTOCROSSLINKING PRODUCTS FORMED BY CYCLIZED POLYISOPRENE-DIAZIDE SYSTEM UNDER THE INFLUENCE OF ALKYL BENZENE SULFONIC ACIDS

The degradation mechanism of photocrosslinking products formed by cyclized polyisoprene-diazide system under the influence of the different alkyl benzene sulfonic acids was studied. The effects of alkyl chain length and the concentration of alkyl benzene sulfonic acids on the rate of degradation reaction were discussed. It was found that in the initial stage of degradation, the cyclicity ratio and the average fused ring number did not change considerably, but the percentage of uncyclized parts content varied significantly. The suitable mechanism was supposed.     

聚合物负载的钯-咪唑催化烯烃加氢

A polymer-supported palladium-imidazole catalyst was used to catalyze the hydrogenation of various olefins under mild conditions. The rate of hydrogenation was studied. The effects of factors such as substrate concentration,catalyst concentration,partial pressure of hydrogen and temperature on initial rate of reaction of selected olefins were investigated. A mechanism for the reaction was proposed from the rate equation. The effects of the solvent and structure of the olefin on the rate of hydrogenation were investigated. The catalyst showed good reusability without any leaching of metal from the support. The homologous analog of the polymer-supported catalyst could not be used as catalyst for the hydrogenation of olefins in methanol because there was precipitation of the metal during reaction.     

Fabrication and Characterization of Diatomite-supported Activated Carbon Functional Ceramic

Using porous diatomite ceramic as carrier and phenolic resin as carbon precursor, the activated carbon functional ceramic with the activated carbon fixed into porous ceramic was prepared by the impregnation load phenolic resin, carbonization and activation isolated air. The influences of impregnation, curing, carbonization, activation etc. on the material property were discussed. The iodine value, SEM, elemental analyzer, BET and spectrum analysis chart were used to characterize the microstructures and performance of material at different conditions. The results showed that the excellent comprehensive property of activated carbon functional ceramic was gained when it adsorbed phenolic resin in 4 h under vacuum condition at curing temperature of 150 ℃ for 0.5 h and carbonization temperature of 600 ℃ for 1.0 h, and then put into 25wt% KOH for 4.0 h at activation temperature of 700 ℃ for 1.5 h. The iodine value is 176.9 mg/g, the specific surface area can reach 86.3 m2/g and the yield of carbonization is 50.48%.