Thermal,mechanical, and morphological properties of soybean oil-based polyurethane/epoxy resin interpenetrating polymer networks (IPNs)

A series of interpenetrating polymer networks (IPNs) based on epoxy (EP) resin and polyurethane (PU) prepolymer derived from soybean oil-based polyols with different mass ratios were synthesized. The structure, thermal properties, damping properties, tensile properties, and morphology of soybean oil-based PU/EP IPNs were characterized by Fourier-transform infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), universal test machine, and scanning electron microscopy (SEM). DSC and DMA results show that the glass transition temperature of the soybean oil-based PU/EP IPN decreases with the increase of PU prepolymer contents. Soybean oil-based PU/EP IPNs have better damping properties than that of the pure epoxy resin. The tensile strength and modulus of PU/EP IPNs decrease, while elongation at break increases with the increase of PU prepolymer contents. SEM observations reveal that phase separation appears in PU/EP IPNs with higher PU prepolymer contents.     

Synthesis and characterization of novel segmented polyurethane/clay nanocomposite via poly(ε-caprolactone)/clay

A novel segmented polyurethane/clay (PU/clay) nanocomposite based on poly(caprolactone), diphenylmethane diisocyanate, butanediol, and poly(caprolactone)/clay prepolymer was synthesized as evidenced by FTIR and X-ray diffraction studies. Poly(caprolactone)/clay (PCL/clay) prepolymer was first synthesized in a nanocomposite form as confirmed by X-ray diffraction. X-ray diffraction study showed that PU/clay contained crystalline structure due to the presence of PCL/clay. In mechanical properties, about 1.4% PCL/clay in PU/clay resulted in a large increase in the elongation of PU/clay. However, when the amount of PCL/clay was 4.2%, the elongation of PU/clay was reduced drastically. This behavior indicated that PU/clay can be transformed from an elastomer to a thermoplastic material as the amount of PCL/clay in PU/clay increased. Additionally, the lap shear stress of PU/clay was at least three times that of neat PU as a result of the PCL/clay component. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2225–2233, 1999     

Proton mobility in hydrated sulfonated polystyrene: NMR and impedance studies

Different ionomers were obtained by sulfonation of a commercial polystyrene (PS), using acetyl sulfate as reagent. The sulfonation was assessed by FTIR and XPS spectroscopies and the thermal and mechanical properties were deduced from DMA measurements. The acid form of the ionomers was characterized by means of ¹H and ¹³C MAS-NMR spectroscopies. Polymer hydration under controlled humidity atmosphere was analyzed by gravimetric, NMR and complex impedance techniques. In the hydrated state, two stages associated with formation of hydronium (H₃O⁺) species and proton hopping between adsorbed water molecules were deduced from NMR data. Both processes are responsible for important changes detected in mechanical properties and conductivity of sulfonated polymers during hydration processes.     

o-Alkyl-substituted aromatic phosphanes for hydroformylation studies: synthesis, spectroscopic characterization and ab initio investigations

In earlier hydroformylation studies modification of the rhodium catalyst with o-methyl-substituted or o-ethyl-substituted phosphane ligands have increased regioselectivity to branched aldehydes. The promising results achieved created a need for further studies. Hence, a wider group of o-substituted arylphosphane ligands, e.g. (2-cyclohexylphenyl)diphenylphosphane, (2-isopropylphenyl)diphenylphosphane, (2-methylnaphthyl)diphenylphosphane, (2,5-dimethylphenyl)diphenylphosphane and (2-phenylphenyl)diphenylphosphane were synthesized and tested in rhodium-catalyzed hydroformylation to support the previous findings. Characterization of the ligands was made by NMR spectroscopy (¹H, ³¹P{¹H}, ¹³C{¹H}, HSQC, COSY-90 and COLOC). Additional parameters for evaluation of the stereoelectronic properties of the ligands were provided by quantum mechanical calculations and by synthesizing Rh(acac)(CO)(PR₃) complexes. In the rhodium-catalyzed hydroformylation of propene and 1-hexene the ligands increased the formation of branched aldehydes compared to triphenylphosphane. Additionally the increasing size of the o-alkyl-substituent was found to effect favorably to the iso-selectivity.     

预聚法丁腈羟聚氨酯/聚丙烯酸甲酯互穿网络聚合物的研究

采用同步法合成了预聚法丁腈羟聚氨酯/聚丙烯酸甲酯类互穿网络聚合物,研究了不同NCO基含量,不同组份比对聚合物抗张强度、剪切强度的影响,还以热失重方法对该体系的耐热性作了探讨。结果指出,聚合物的机械性能和耐热性皆比单一组成聚合物高,而且在组份比(PU/PMA)=8/2时机械性能有最大值,其协同效应显著。     

Synthesis of new o-alkyl substituted arylalkylphosphanes: study of their molecular structure and influence on rhodium-catalyzed propene and 1-hexene hydroformylation

A set of new phosphane ligands designed to increase the branched-to-normal ratio of the hydroformylation reaction were prepared in the same way as the previously reported ortho-alkyl substituted arylphosphanes, which have shown increased i/n ratios in the hydroformylation of propene and 1-hexene. In order to determine the relationship between the catalytic behavior and stereoelectronic properties of the ligands, various functional alkyl groups (methyl, isopropyl, cyclohexyl) were placed on the phosphorus atom directly and in the ortho position of the phenyl ring connected to phosphorus. In the hydroformylation reaction of propene and 1-hexene a higher i/n ratio resulted with nearly all the ligands compared with that of triphenylphosphane. Additionally as the ortho-alkyl-substituent became larger, it had a favorable effect on the i-selectivity. Characterization of the ligands was carried out by NMR spectroscopy (mainly ¹H, ³¹P{¹H}, ¹³C{¹H}, HSQC/HETCOR and COSY-90). Properties of the ligands were also studied by quantum mechanical calculations and by synthesizing three Rh(acac)(CO)(PR₃) derivatives. The o-alkyl-substituent was orientated outside the ligands’ cone angle in the X-ray crystal structures of (2-cyclohexylphenyl)dicyclohexylphosphane and (2,5-dimethylphenyl)bis(4-pyridyl)phosphane, and Rh(acac)(CO)(PR₃) complex of (2-methylphenyl)dicyclohexylphosphane.     

酸碱存在下水溶性铑膦配合物的NMR表征及氢甲酰化性能研究

31P(¹H)NMR和¹HNMR研究表明,当NaOH加入到水溶性铑膦配合物HRh(CO)·(TPPTS)₃[TPPTS:P(m-C₆H₄SO₃Na)₃]后,可观察到有少量的OTPPTS[OTPPTS:O=P(m-C₆H₄SO₃Na)₃]出现,但配合物的特征谱峰即使在高浓度的NaOH存在下也基本保持不变,表明NaOH对配合物分子结构的影响较小;当吡啶加入到HRh(CO)(TPPTS)₃中,³¹P(¹H)NMR谱图中出现游离配体TPPTS的³¹P谱峰及若干结构未知的新水溶性配合物的³¹P谱峰,表明吡啶分子将与配合物分子中的配体TPPTS发生配体交换反应.在HRh(CO)(TPPTS)₃中分别加入一定量的HCl,HNO₃,H₂SO₄和H₃PO₄等无机酸时,随着酸量的增加,配合物的³¹P物种含量逐渐下降,而OTPPTS量明显上升,直至配合物³¹P物种完全消失;高浓度乙酸对配合物结构的影响与上述无机酸类似.HRh(CO)(TPPTS)₃的1-己烯氢甲酰化催化反应结果表明,碱存在下可获得较高的正异构醛比值,但催化活性降低;酸存在下所得产物正异构醛比值相对较低且呈淡黄色.     

The reaction of (μ-H)2Os3(CO)9(PPh3) with ethylene affords the ethylidene complex (μ-H)2Os3(CO)9(PPh3)(μ-CHCH3)

The product isolated from the reaction of (μ-H)₂Os₃(CO)₉(PPh₃) with ethylene is shown to be the ethylidene complex (μ-H)₂Os₃(CO)₉(PPh₃)(μ-CHCH₃) (1) rather than the ethylene complex (μ-H)(H)Os₃(CO)₉(PPh₃)(C₂H₄), as previously claimed. The characterization of 1 is based on a combination of ¹H and ¹³C NMR results. The ¹H NMR data (δ 6.84 (1 H_D), 2.53 (3 H_C), J(CD) = 7.4 Hz) establish the presence of the ethylidene moiety, whereas detailed analysis of the 1-D and 2-D ¹³C NMR spectra of ¹³CO-enriched 1 indicates the relative positions of the ethylidene, hydride, and phosphine ligands on the triosmium framework.     

不饱和糖功能单体接枝聚氨酯膜的制备及其血液相容性

通过葡萄糖、丙烯酸羟乙酯和丁二胺反应,制备了含不饱和双键的糖基功能单体。 采用傅里叶红外光谱和核磁共振氢谱对合成的产物进行结构表征确定。 采用紫外光引发接枝聚合技术,将制备的不饱和糖单体接枝聚合到聚氨酯膜的表面,以衰减全反射模式下傅里叶红外光谱对表面接枝反应进行了确认。 通过静态水接触角实验和血小板黏附实验,分别对改性聚氨酯膜表面的亲水性和血液相容性进行了研究,结果表明,改性聚氨酯膜表面的接触角从86°降低到45°,血小板的粘附量由14.36×10³ cells/mm²减少到2.57×10³ cells/mm²,亲水性明显增强,血液相容性显著改善。     

Formation, solution structure and reactivity of alkylperoxo complexes of titanium

A detailed in situ ¹³C and ¹H NMR spectroscopic characterization of the following families of alkylperoxo complexes of titanium is presented: Ti(η²-OOtBu)_n(OiPr)_4−n, where n = 1–4; binuclear complexes [(iPrO)₃Ti(μ-OiPr)₂Ti(OiPr)₂(η²-OOtBu)] and [(η²-OOtBu)(iPrO)₂Ti(μ-OiPr)₂Ti(OiPr)₂(η²-OOtBu)]; complexes with β-diketonato ligands: Ti(LL)₂(OEt)(η²-OOtBu), Ti(LL)₂(OiPr)(η²-OOtBu), Ti(LL)₂(η²-OOtBu)₂, Ti(LL)₂(OtBu)(η¹-OOtBu), where HLL = acetylacetone, dipivaloylmethane. These alkylperoxo complexes could not be isolated due to their instability and were studied in situ at low temperatures. Whereas the side-on (η²) coordination mode of tert-butylperoxo ligand is generally preferable, the end-on (η¹) coordination caused by spatial hindrance from surrounding bulky ligands is found in two cases. The quantitative data on the reactivity of alkylperoxo complexes found towards sulfides and alkenes were obtained. The system TiO(acac)₂/tBuOOH in C₆H₆ was reinvestigated using ¹³C and ¹H NMR spectroscopy. The structure of the complex Ti(acac)₂{CH₃C(O)(OOtBu)COO} actually formed in this system was elucidated. Four types of titanium(IV) alkylperoxo complexes were detected in the Sharpless–Katsuki catalytic system using ¹³C NMR spectroscopy.     

Preparation and characterization of [Re(bpy)(CO) 3L][SbF6] (L = phosphine, phosphite)

A series of rhenium complexes [fac-Re(bpy)(CO)₃L][SbF₆] (bpy = 2,2′-bipyridine, L = P(ⁿBu)₃, PEt₃, PPh₃, P(OMe)Ph₂, P(OⁱPr)₃, P(OEt)₃, P(OMe)₃, P(OPh)₃) has been prepared and characterized by the IR, UV-vis, ¹H NMR, ³¹P NMR, X-ray photoelectron spectroscopy and electrochemical techniques. Variations in the electronic properties, i.e. CO stretching, metal-to-ligand charge transfer transition, and ³¹P NMR chemical shifts were interpreted on the basis of the electron-acceptor strength of L. However, the redox potential corresponding to [Re(bpy)(CO)₃L]⁺/[Re(bpy⁻)(CO)₃L]showed ‘V-character type’ changes after the increase in the electron-acceptor strength of L. Variation of the P(2p) binding energy of the phosphorus atom indicated that the electronic structure of the coordinated phosphorus atom was strongly influenced by the electronic properties of the directly attached substituents.     

Preparation of high‐temperature polyurethane by alloying with reactive polyamide

A series of novel poly(urethane amide) films were prepared by the reaction of a polyurethane (PU) prepolymer and a soluble polyamide (PA) containing aliphatic hydroxyl groups in the backbone. The PU prepolymer was prepared by the reaction of polyester polyol and 2,4‐tolylenediisocyanate and then was end‐capped with phenol. Soluble PA was prepared by the reaction of 1‐(m‐aminophenyl)‐2‐(p‐aminophenyl)ethanol and terephthaloyl chloride. The PU prepolymer and PA were blended, and the clear, transparent solutions were cast on glass substrates; this was followed by thermal treatments at various temperatures to produce reactions between the isocyanate group of the PU prepolymer and the hydroxyl group of PA. The opaque poly(urethane amide) films showed various properties, from those of plastics to those of elastomers, depending on the ratio of the PU and PA components. Dynamic mechanical analysis showed two glass‐transition temperatures (T_g's), a lower T_g due to the PU component and a higher T_g due to the PA component, suggesting that the two polymer components were phase‐separated. The rubbery plateau region of the storage modulus for the elastic films was maintained up to about 250 °C, which is considerably higher than for conventional PUs. Tensile measurements of the elastic films of 90/10 PU/PA showed that the elongation was as high as 347%. This indicated that the alloying of PU with PA containing aliphatic hydroxyl groups in the backbone improved the high‐temperature properties of PU and, therefore, enhanced the use temperature of PU. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3497–3503, 2002     

Photochemical reactions of alkynyl iron (II) complexes with carbon disulfide. Insertion of CS2 into an iron-C(sp) bond

The novel alkynyldithiocarboxylate complexes [Fe(η⁵-C₅H₅)(S₂CCCR) (dppm-P)] (3a,b) and [Fe(η₅-C₅H₅)(S₂CCCR)(PPh₃)] (4a,b) were obtained through the insertion of CS₂ into the iron-akynyl bond in the complexes [Fe(η₅-C₅H₅)(CCR)(L)(L′] L, L′ = dppm R = Ph (1a), ^tBu(1b); L = (CO), L′ = (PPh₃) R = Ph (2a), ^tBu (2b). Variable-temperature ³¹P{¹H} NMR studies indicate the presence of two different isomers, [Fe(η⁵-C₅H₅)(η³-S,C,S′---S₂CCCR)(L)(L′)] and [Fe(η⁵-C₅H₅(η²-S,S′-S₂CCCR)(L)(L′)], which rapidly interconvert at room temperature. The synthesis of the precursor complex [Fe(η⁵-C₅H₅)(CC^tBu)(CO)(PPh₃)] is also described.     

Synthesis,Characterization and Application of Poly(lactic-co-glycolic acid) with a Mass Ratio of Lactic to Glycolic Segments of 52/48

Poly(lactic-co-glycolic acid)(PLGA) is one of the most representative degradable copolymers and promising drug carriers. In the current paper, the PLGAs with a lactic acid/ glycolic acid(LA/GA) molar ratio of 52/48 and various molecular weights were prepared by a melting method. The molecular weight, molecular weight distribution, and thermal stability were determined by ¹H NMR and thermogravimetric analysis methods. The results demonstrated that PLGAs with the fixed LA/GA molar ratio(52/48), different molecular weights, and narrow molecular weight distribution could be obtained by solely altering the reaction time. The PLGA films were prepared, and their properties including micro-structure, mechanical property, in-vitro cytotoxicity, and biodegradability were characterized. In combination with the homogeneous microstructures and mechanical properties, the drug-loading and releasing properties of PLGA_3.2 films were investigated. The results show that PLGA_3.2 film with an LA/GA molar ratio of 52/48 is a promising curcumin carrier.     

PU／PMMA—IPN体系的反应动力学研究

采用FT-IR法研究了聚氨酯/聚甲基丙烯酸甲酯互穿网络聚合物(PU/PMMA-IPN)的光固化和热固化动力学以及固化方式对聚合物形态和力学性能的影响。实验结果表明:当PU/PMMA-IPN的组成百分含量为75/25时,光固化试样的抗张强度(22.6MPa)和伸长率(201%)均高于热固化试样(抗张强度18.6PMa伸长率69%)。这是因为光固化时甲基丙烯酸甲酯(MMA)迅速聚合形成凝胶产生“速冻”效应,阻碍了PU予聚体迁移分相,从而提高了聚合物网络的互穿程度,此结果亦为电镜照片所证实。     

萘酰亚胺类荧光染料及共聚型荧光聚氨酯乳液的合成与性能

首先以4-溴-1,8-萘酐、2-氨基-1,3-丙二醇和甲醇钠为原料, 经亚胺化和取代两步反应合成出4-甲氧基-N-(2-羟基-1-羟甲基乙基)-1, 8-萘酰亚胺(MHHNA)活性荧光染料, 然后将其作为扩链剂通过相反转自乳化法制备出了共聚型荧光聚氨酯(PU) (PU-MHHNA)乳液, 并分别采用核磁共振氢谱(¹H NMR)、核磁共振碳谱(¹³CNMR)、元素分析、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)吸收光谱、荧光光谱、粒度分析、氙灯老化等方法对所得荧光染料的化学结构、PU乳液及乳胶膜的性能进行了表征. 结果表明, MHHNA和PU-MHHNA的荧光量子产率分别为0.73 和0.92, MHHNA的用量对所得PU乳液的胶体性质没有明显影响. PU-MHHNA的丙酮溶液在UV-Vis 吸收光谱上的最大吸收波长(λ_max)为360.6 nm, 在荧光光谱上的最大激发波长(λ_ex)和最大发射波长(λ_em)分别为362和435 nm. 随着温度的升高, PU-MHHNA的荧光强度逐渐降低. PU-MHHNA乳胶膜的耐光色牢度和耐溶剂色牢度均明显高于共混型荧光聚氨酯(PU/MBNA)乳胶膜.     

温敏性纤维素/聚N-异丙基丙烯酰胺复合水凝胶的固体核磁共振表征及动力学研究

利用半互穿网络方法将具有温度响应的高分子聚N-异丙基丙烯酰胺(PNIPAM)与天然纤维素复合得到温敏性水凝胶. 通过固体核磁共振的 ¹H, ¹³C CP/MAS(交叉极化/魔角旋转)和QCP(定量交叉极化)等实验手段对复合凝胶的结构进行了定性及定量研究, 并利用固体静态变温核磁共振实验和偶极滤波-自旋扩散实验研究了复合凝胶中PNIPAM分子链段的动力学行为.     

Molecular structure of meso-tetraphenylporphyrinatothallium(III) cyanide: Tl(tpp) (CN)

meso-Tetraphenylporphyrinatothallium(III) cyanide, Tl(tpp)(CN), was previously assumed to be monomeric and has been confirmed by X-ray analysis to exist as two independent molecules in one asymmetric unit. This unit displays two square-pyramidal coordination geometries for the thallium atoms with the cyano ligand coordinated to both Tl atoms. It crystallizes in the triclinic space group P , with a 10.003(3), b 16.231(7), c 21.277(8) Å, 89.98(3), β 90.57(3), γ 90.31(3)°' and z = 4. The structure was solved by direct methods. A total of 7995 unique reflections having I > 3σ(I) was measured with an automated diffractometer and used to refine the crystal structure to a conventional R factor of 6.05 %. The thallium-cyanide distances are 2.140(14) Å (for thallium(I)) and 2.277(14) Å (for thallium(2)) respectively, with thallium(1) situated 0.908 Å above the porphyrin ring and thallium(2) located 1.027 Å below the ring. IR and NMR spectroscopy p rovide complementary methods for investigation of the CN ligand. The characteristic band observed at 2160 cm⁻¹ in the FTIR spectrum is assigned to the CN stretching in the Tl(tpp)(CN) complex. The ¹³C resonance of axial cyano ligand is observed with a pulse delay of 3.5 s at 24°C at 139.2 ppm (with ¹J(²⁰⁵Tl-¹³C) 5394 and ¹J(²⁰³Tl-¹³C) 5344 Hz). This observation disagrees with the conclusion, drawn from previous work, in that an exchange process involving the apical ligand explains the invisibility due to line broadening at 35°C of the ¹³C signal.     

硫代多联吡啶铂(Ⅱ)配合物的合成、性质及在光催化制氢中的应用

合成了2个新配体4-(4-硫代乙酸)甲苯基-6-苯基-2,2'-联吡啶HC^N^N(PhCH₂SCOCH₃)(L3)和6-(4-硫代乙酸)甲苯基-2,2'-联吡啶 HC^N^N (CH₂SCOCH₃)(L5)及其发光的铂(Ⅱ)配合物ClPtC^N^N(PhCH₂SCOCH₃)(C3)和ClPtC^N^N(CH₂SCOCH₃)(C5). 通过¹H NMR谱和质谱对它们的结构进行了表征, 采用X射线单晶衍射分析确定了C3的晶体结构. 利用紫外-可见吸收光谱、 发射光谱及激发态寿命测定研究了它们的光物理性质和电化学性质, 以及配合物作为光敏剂在光催化制氢中的应用. 通过系列配合物产氢效率的比较, 揭示了它们的产氢效率和激发态寿命的关系.     

本体共聚合制备丙烯/1-丁烯合金及表征

以球形高效负载的TiCl₄/MgCl₂/邻苯二甲酸二异丁酯(DIBP)为催化剂, 采用本体聚合方法进行丙烯与1-丁烯共聚合研究. 考察了共单体效应对共聚活性及聚合物立构规整性的影响; 表征了共聚物的结构. 结果表明, 随着1-丁烯/丙烯投料比的增加, 聚合活性呈先升高后降低的趋势, 在1-丁烯/丙烯摩尔投料比为0.26条件下聚合活性达到最高, 并随着共聚物中1-丁烯含量的增加, 共聚物的熔点明显下降, 分子量降低, 分子量分布变窄, 同时共聚物力学性能有明显提高, 透明度逐渐增加.