排序方式: 共有74条查询结果,搜索用时 15 毫秒
1.
过渡金属Ni是地球上储量丰富的金属元素, 在加氢脱硫、重整制氢等催化领域应用非常广泛, 但是关于Ni基催化剂在烷烃脱氢方面的研究较少; 因此, 本工作采用不同的方法, 制备了三种结构的Ni基负载催化剂, 即尖晶石分解型、浸渍型和钙钛矿析出型, 并在700 ℃、C2H6-N2气氛中和50 mL•min-1气体流速下, 探索了它们的乙烷脱氢性能. 结果表明: 尖晶石分解型催化剂Ni1-xCuxCr2O4还原后在Cr2O3表面形成Ni-Cu合金颗粒, 能有效钝化Ni的C—C键断裂活性, 提高乙烯的选择性. Ni含量过高时, Ni不能有效地分散而形成大的金属团簇, 造成乙烷过度裂解, 乙烯选择性较低. 浸渍负载型催化剂NixMy/Al2O3 (M为Cu或Ag) 比表面积大, 表面活性位点分散, 但活性金属与载体结合力弱, 在高温下不稳定; Cu或Ag与Ni形成合金, 可有效提高乙烯选择性, Ag较Cu的效果更佳. 钙钛矿析出型催化剂LaCr1-xNixO3(LCNi-100x)在还原气氛中析出均匀细小的Ni颗粒, 其与基体结合力强, 抗积碳性能和稳定性较高; 含15% Ni的LCNi-15还原后(R-LCNi-15)表现出最好的催化性能, 乙烯产率最高(24%), 同时具有较好的抗积碳性能和稳定性以及氧化再生性. 相似文献
2.
Polar Dependence of Threading Dislocation Density in GaN Films Grown by Metal-Organic Chemical Vapor Deposition 下载免费PDF全文
We investigate the threading dislocation(TD) density in N-polar and Ga-polar GaN films grown on sapphire substrates by metal-organic chemical vapor deposition.X-ray diffraction results reveal that the proportion of screw type TDs in N-polar GaN is much larger and the proportion of edge type TDs is much smaller than that in Ga-polar.Transmission electron microscope results show that the interface between the AlN nucleation layer and the GaN layer in N-polar films is smoother than that in Ga-polar films,which suggests different growth modes of GaN.This observation explains the encountered difference in screw and edge TD density.A model is proposed to explain this phenomenon. 相似文献
3.
A torsion balance is constructed to accurately measure the magnetic properties of the real proof mass of the inertial sensor. The magnetic susceptibility and remnant moment of a titanium proof mass are measured in the first experiment, and further improvements and the potential sensitivity are also discussed. This is significant for choosing the material of the proof mass and investigating the magnetic disturbances acting on the proof mass. 相似文献
4.
5.
讨论格自仿Tile的边界结构,得到平面格自仿Tile的边界为简单闭曲线的一个充分条件;作为应用,给出Bandt-Wang的一个定理的新证明. 相似文献
6.
本文通过对蓬安县三元水库大坝外坡裂缝产生的原因分析,进而运用岩、土力学的理论与方法反算推论出了裂缝的产生不是深层坝体土滑动引起的,而是局部浅层坝体土在水的诱发作用下作蠕滑-拉裂变形所产生的。在明确了大坝裂缝产生的原因后,提出了一系列相应整治工程措施,以达到彻底根治裂缝和稳固大坝的目的。 相似文献
7.
A prototype of a device with an impact structure for measuring the floor tilt has been built in our laboratory. The mechanical construction and the capacitive transducer of the device are introduced. Experimental results indicate that the floor tilt is about 16#tad in our cavity laboratory, and the uncertainty AG/G caused by such tilt is less than 0.54 parts per million (ppm), so the floor tilt can be reasonably neglected in the experimental determination of the gravitational constant G with the total uncertainty of about l0ppm. 相似文献
8.
9.
OPTIMUM DURATION OF MEASUREMENT FOR REDUCING THERMAL NOISE LIMITATIONS IN TORSION PENDULUM EXPERIMENTS 下载免费PDF全文
Statistical estimates of thermal noise fluctuation of a linear harmonic oscillator used to detect weak forces are reexamined with special reference to gravitational experiments. Thermal noise limitation on the measurement of displacement of an oscillator is studied. It is found that the signal response of an oscillator reaches the maximum value while the thermal noise response reaches the minimum value at the same time during the transient state of the oscillator, and the precision of the experiments in the transient state could increase about two orders higher than that in the equilibrium state for typical experiments. It is also found that there is an optimum duration of measurement in which the uncertainty due to thermal noise in this period is the least. 相似文献
10.
A phenomenological study on the fitting method in real time has been done, and the method was applied to process and analyze the extensive data of a long period torsion pendulum used to determine Newtonian gravitational constant G. The result shows that the fitting method in real time is effective to determine the period of a torsion pendulum with a relative precision of 10-5 orders. 相似文献