Imprint lithography of pyramidal photonic pillars using hydrazine etching

An inexpensive method to produce a pyramidal-type 2D photonic structures in the silicon substrate was proposed. The method is based on the combination of imprint lithography and wet Si1 0 0 etching in water solution of hydrazine, which etches 1 1 1 faces much more slowly than others. Thermally grown SiO₂ mask for the hydrazine etching was used, because single Al mask cannot be well bonded to the substrate and tends to peel during the etching. It was revealed that transmittance in the infrared spectrum region of the patterned silicon decreases by about five times compared with that of flat silicon substrate and this decrease is almost independent of the angle of the incident beam. In the infrared region, decrease of transmittance of the patterned samples is directly proportional to the wave number. The shape of formed pyramids has strong influence on the transmittance. Decrease of the transmittance is much more rapid and larger in the case of sharpless pillars.     

电致发光色纯性增强的硅基有机微腔

报道了硅基有机微腔的电致发光（EL）.该微腔由上半透明金属膜、中心有源多层膜和多孔硅分布Bragg反射镜（PS DBR）组成.半透明金属膜由Ag（２０nm）构成，充当发光器件的负电极和微腔的上反射镜.有源多层膜由Al (1 nm) / LiF(05 nm) /Alq3/Alq3:DCJTB/NPB/CuPc/ITO/SiO2组成，其中的Al/LiF为电子注入层，ITO为正电极，SiO2为使正、负电极电隔离的介质层.该PS DBR是采用设备简单、成本低廉且非常省时的电化学腐蚀法用单晶Si来制备的；该PS 关键词： 电化学腐蚀 电致发光 窄峰发射 硅基有机微腔     

Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.     

Microstructure effect on microtopography of chemically etched α + β Ti alloys

Microstructure effect on chemical etching behavior of the annealed Ti-6Al-4V and Ti-3Al-2.5V titanium (Ti) alloys was compared with that of unalloyed commercially pure titanium. The microstructural evolution of structure phases after annealing the titanium and its alloys at temperature near and above β transus and followed by furnace cooling to room temperature was studied using optical microscope, scanning electron microscope and X-ray diffraction techniques. The microstructure study illustrates that the heat treatment enhanced partitioning effect allows extensive formation of hemispherical and near spherical pits roughened surface to be readily acquired by chemically etching the annealed α + β titanium alloys. The kinetics of the chemical etching reaction process show a linear dependence on time. The annealed α + β titanium alloys that exhibit relatively lower weight loss and thickness reduction rate illustrate less chemical activity than the annealed unalloyed titanium.     

Microstructure array on Si and SiOx generated by micro-contact printing, wet chemical etching and reactive ion etching

A method, combining micro-contact printing (μCP), wet chemical etching and reactive ion etching (RIE), is reported to fabricate microstructures on Si and SiOx. Positive and negative structures were generated based on different stamps used for μCP. The reproducibility of the obtained microstructures shows the methodology reported herein could be useful in Micro-Electro-Mechanical Systems (MEMS), optical and biological sensing applications.     

Angular response characteristic of pyramid shape fast neutron dosimeter using CR-39 films

CR-39 is a highly sensitive etched track detector for neutron monitoring and dosimetry applications but its dose equivalent response is strongly direction dependent with respect to the incident neutrons. This is considered to be a major drawback for their use. In the present study, an attempt has been made to develop a pyramid shaped dosimeter, which consists of polyethylene material of thickness 1 mm with the provision to hold three CR-39 films at an angle of 35° to each other. The response of CR-39 in this configuration under optimum electrochemical etching at elevated temperature have been found nearly angular independent and therefore the dosimeter can be used for neutron monitoring, i.e. personnel as well as area monitoring.     

Fabricating blazing grating on NGD by photochemical etching

This paper tries to introduce the reader to the method of using photochemical re-action to copy holographic optical elements(HOEs)in relief.The holographic blazing gratingso copied is groove depth adjustable phase modulability enlarged through copying and 3.3times the diffraction efficiency(DE)of the original grating.It is expected that the newmethod will lead to the mass production of the light-weight HOEs at low cost.     

软X射线显微术Si_3N_4薄膜窗口的研制

介绍了在软Ｘ－射线显微术研究领域中有重要应用的Ｓｉ_３Ｎ_４薄膜窗口的实验室制作方法，并形成一套独特制备工艺，Ｓｉ_３Ｎ_４薄膜窗口的研制成功推动了我国软Ｘ射线显微术研究的发展。     

n型砷化镓微区光电化学腐蚀过程

在n-GaAs电解液界面,用聚焦He-Ne激光照射, 使n-GaAs表面发生微区光电化学腐蚀, 用计算机控制步进马达, 使试样在X-Y二维方向扫描移动, 能在晶片上得到刻蚀点直径2 μm的刻蚀图案. 研究了激光相对光强, KOH、H_2SO_4、KCl等刻蚀剡的浓度, 光腐蚀的时间, 电极电位等因素对腐蚀点的直径和深度的影响, 通过实验数据找出腐蚀过程的规律, 并用光电化学原理进行解释.