Surface charging behaviors of electrocatalytic interfaces with partially charged chemisorbates

The surface charge is a key concept in electrochemistry. Mathematically, the surface charge is obtained from a spatial integration of the volume charge along a particular direction. Ambiguities thus arise in choosing the starting and ending points of the integration. As for electrocatalytic interfaces, the presence of chemisorbates further complicates the situation. In this minireview, I adopt a definition of the surface charge within a continuum picture of the electric double layer. I will introduce surface charging behaviors of firstly ordinary electrochemical interfaces and then electrocatalytic interfaces featuring partially charged chemisorbates. Particularly, the origin of nonmonotonic surface charging behaviors of electrocatalytic interfaces is explained using a primitive model. Finally, a brief account of previous studies on the nonmonotonic surface charging behavior is presented, as a subline of the spectacular history of electric double layer.     

单层MXene纳米片Ti2N电磁特性的过渡金属(Sc、V、Zr)掺杂效应

二维材料MXene纳米片由于具有较大的比表面积和较高的电子迁移率而受到广泛的关注。本文采用基于密度泛函理论的第一性原理计算,对单层MXene纳米片Ti₂N电磁特性的过渡金属(Sc、V、Zr)掺杂效应进行了系统研究。结果表明,所有过渡金属掺杂体系结合能均为负值,结构均稳定;其中Ti₂N-Sc体系的形成能为-2.242 eV,结构更易形成,且保持稳定;掺杂后Ti₂N-Sc、Ti₂N-Zr体系磁矩增大;此外,Ti₂N-Sc体系中保留了较高的自旋极化率,达到84.9%,可预测该体系在自旋电子学中具有潜在的应用价值。     

Multivariate optimization and comparison between conventional extraction (CE) and ultrasonic-assisted extraction (UAE) of carotenoid extraction from cashew apple

Carotenoids are an essential component of cashew and can be used in pharmaceuticals, cosmetics, natural pigment, food additives, among other applications. The present work focuses on optimizing and comparing conventional and ultrasound-assisted extraction methods. Every optimization step took place with a 1:1 (w:w) mixture of yellow and red cashew apples lyophilized and ground in a cryogenic mill. A Simplex-centroid design was applied for both methods, and the solvents acetone, methanol, ethanol, and petroleum ether were evaluated. After choosing the extractor solvent, a central composite design was applied to optimize the sample mass (59–201 mg) and extraction time (6–34 min). The optimum conditions for the extractor solvent were 38% acetone, 30% ethanol, and 32% petroleum ether for CE and a mixture of 44% acetone and 56% methanol for UAE. The best experimental conditions for UAE were a sonication time of 19 min and a sample mass of 153 mg, while the CE was 23 min and 136 mg. Comparing red and yellow cashews, red cashews showed a higher carotenoid content in both methodologies. The UAE methodology was ca. 21% faster, presented a more straightforward composition of extracting solution, showed an average yield of superior carotenoid content in all samples compared to CE. Therefore, UAE has demonstrated a simple, efficient, fast, low-cost adjustment methodology and a reliable alternative for other applications involving these bioactive compounds in the studied or similar matrix.     

Development of a Chitosan/Nickel Phthalocyanine Composite Based Conductometric Micro-sensor for Methanol Detection

Thin-film composite of chitosan/nickel phthalocyanine (NiPc) was electrochemically deposited on the fingers of interdigitated gold electrodes, applying chronoamperometric polymerization technique. The presence of crystallized NiPc in the chitosan was confirmed by EDX and FTIR analysis. Acetone, ethanol, and methanol gas-sensing properties of the films prepared at optimum conditions were studied at atmospheric temperature, through differential measurements at an optimized frequency of 10 kHz, using a lock-in amplifier. The conductometric sensor presents the highest sensitivity of 60.2 μS.cm⁻¹(v/v) for methanol and 700 ppm as the limit of detection. For validation, the methanol content of a commercial rubbing alcohol was determined.     

Effect of strain on charge density wave order in α-U

The effect of strain on charge density wave (CDW) order in $\alpha$-U is investigated within the framework of relativistic density-functional theory. The energetical stability of $\alpha$-U with CDW distortion is enhanced by the tensile strain along $a$ and $b$ axes, which is similar to the case of negative pressure and normal. However, the tensile strain along $c$ axis suppresses the energetical stability of CDW phase. This abnormal effect could be understood from the emergence of a new one-dimensional atomic chain along $c$ axis in $\alpha$-U. Furthermore, this effect is supported by the calculations of Fermi surface and phonon mode, in which the topological objects and the dynamical instability show opposite behaviors between strains along $a$/$b$ and $c$ axes.     

Diffusion Model of a Non-Integer Order PIγ Controller with TCP/UDP Streams

In this article, a way to employ the diffusion approximation to model interplay between TCP and UDP flows is presented. In order to control traffic congestion, an environment of IP routers applying AQM (Active Queue Management) algorithms has been introduced. Furthermore, the impact of the fractional controller PIγ and its parameters on the transport protocols is investigated. The controller has been elaborated in accordance with the control theory. The TCP and UDP flows are transmitted simultaneously and are mutually independent. Only the TCP is controlled by the AQM algorithm. Our diffusion model allows a single TCP or UDP flow to start or end at any time, which distinguishes it from those previously described in the literature.     

1,3,5-三(羧基甲氧基)苯镍配位聚合物的合成、晶体结构及性质研究

采用溶剂热法,1,3,5-三(羧基甲氧基)苯为定向配体和乙酸镍反应构筑了一个新型的金属配位聚合物[Ni(TB)₂(H₂O)₂]_n·2H₂O,其中H₃TB=1,3,5-三(羧基甲氧基)苯,通过元素分析、IR及X射线单晶衍射对配合物结构进行表征,并研究其荧光性质、热稳定性及Hirshfeld表面作用力。单晶结构分析表明,该配合物属于三斜晶系,空间群$P \overline{1}$,配合物中心离子Ni(Ⅱ)分别与来自两个水分子上的氧原子及四个不同1,3,5-三(羧基甲氧基)苯配体的羧酸氧原子配位,形成六配位的NiO₆八面体构型,并通过与1,3,5-三(羧基甲氧基)苯配体的氧原子配位不断延伸形成具有孔洞结构的一维链状构型。配合物具有良好的荧光性能和热稳定性。Hirshfeld表面作用分析表明配合物分子中O…H/H…O作用占主导且占比为39.0%,而H…H的作用力占比为25.9%,O…O的作用力占比为13.6%。     

Synthesis of flower-like WS2 by chemical vapor deposition

Flower-like tungsten disulfide (WS₂) with a diameter of 5-10 μm is prepared by chemical vapor deposition (CVD). Scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), Raman spectroscopy, and ultraviolet-visible (UV-vis) spectroscopy are used to characterize its morphological and optical properties, and its growth mechanism is discussed. The key factors for the formation of flower-like WS₂ are determined. Firstly, the cooling process causes the generation of nucleation dislocations, and then the "leaf" growth of flower-like WS₂ is achieved by increasing the temperature.