石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

微流控纸芯片的加工及其分析应用的实验设计*

设计了一个使用喷墨打印法加工微流控纸芯片的实验,在经烷基烯酮二聚体(AKD)的正己烷溶液浸泡过的滤纸上,以三乙醇胺溶液为打印墨水,用喷墨打印机打印出设计好的芯片图案。滤纸加热后,打印区域呈现亲水性,非打印区域为疏水性,从而制备出纸芯片,用该纸芯片通过数字比色法实现了亚硝酸根离子的定量测定。该实验不使用昂贵仪器设备,易普及。通过实验,促使学生了解微流控芯片这一前沿科学技术,锻炼学生细致、灵巧的动手能力,激发学生科技创新活力。     

Dynamic Modeling of the Feed Drive System of a CNC Metal Cutting Machine

Studying the vibrational behavior of feed drive systems is important for enhancing the structural performance of computer numerical control (CNC) machines. The preload on the screw and nut position have a great influence on the vibration characteristics of the feed drive as two very important operational conditions. Rotational acceleration of the screw also affects the performance of the CNC feed drive when machining small parts. This paper investigates the influence of preload and nut position on the vibration characteristics of the feed drive system of a CNC metal cutting machine in order to be able to eliminate an observed resonance occurred at high rotational speeds of the screw, corresponding to high feed rates. Additionally, rational structural parameters of the feed drive system are selected in order to increase the rotational acceleration for improving the performance of the CNC machine. Experiments and analyses showed that by selecting specific parameters of feed drive system and simultaneously applying a certain value of preload, a 97% increase in rotational acceleration and 30% time reduction considering the vibration resistance at high rotational speeds can be achieved.     

求解矩阵方程AXB+CXD=F参数迭代法的最优参数分析

本文针对求矩阵方程AXB+CXD=F唯一解的参数迭代法，分析当矩阵A，B，C，D均是Hermite正（负）定矩阵时，迭代矩阵的特征值表达式，给出了最优参数的确定方法，并提出了相应的加速算法.     

INFLUENCE OF FRICTION ON THE MOTION OF BASE WITH AN ECCENTRIC ROTOR

偏心转子惯性力引起的底座运动受到地面摩擦的影响，与光滑情形的理论结果存在定性差异。转子逆时针匀速旋转的惯性力若小于构件总重，则底座随摩擦因子增加而出现连续、一次停顿和两次停顿的振动及完全静止的4种状态。因惯性力对正压力及摩擦力的影响，底座在连续及一次停顿的振动时右向位移较大；而底座跳起时如``蛤蟆夯'则整体向左移动。     

A MODAL TESTING METHOD FOR CANTILEVER BEAM1)

基于欧拉-伯努利梁理论得到悬臂梁自由振动的振型函数。通过数值计算得出实验用的悬臂梁前五阶振型的节点位置及其与梁长的比值。考虑传感器对悬臂梁固有频率的影响,建立梁-传感器模型进行仿真分析并得出悬臂梁前五阶固有频率。基于节点位置和测点位置,在实验中选择激励点。将具体实验的结果与梁-传感器仿真模型结果进行对比,通过前五阶固有频率的误差分析,发现仿真分析结果与实验结果误差最高为 1.3%。研究完整地叙述了悬臂梁的模态测试流程,可为工程技术人员的模态测试起一定的指导作用。     

甲烷-二氧化碳重整制合成气与现代分析技术应用于探究性化工专业实验的设计与探索

以甲烷-二氧化碳重整制合成气为实例，设计探究性实验，将合成气的制备和现代分析技术应用于化工专业实验的教学实践中以提高学生的创新和实践能力。实验包括催化剂的制备，催化剂的性能评价和催化剂的表征等3大部分。采用工业最常用的浸渍法制备含有不同助剂的Ni/X/γ-Al2O3（X为Co，Fe，MgO，CeO2）催化剂，以甲烷-二氧化碳重整反应评价其催化性能，并采用XRD、H2-TPR、BET和TG对催化剂的微观结构进行表征。结合催化剂的性能评价结果和表征结果，探讨不同助剂对镍基催化剂性能的改善效果及机制。通过开设该实验，可以让学生了解化工学科的前沿知识以及现代分析技术的基本原理和用途，掌握专业的实验操作、数据处理和谱图绘制方法，提高学生的专业素养和综合能力。     

Effects of van der Waals force on nonlinear vibration of electromechanical integrated electrostatic harmonic actuator

An electromechanical integrated electrostatic harmonic actuator is promising for the miniaturization of electromechanical devices. As the dimensions of the actuator decrease, the effects of the van der Waals force become obvious. In this study, by considering the nonlinearity of electrostatic and van der Waals forces, nonlinear vibration equations of the flexible ring of an electrostatic harmonic actuator are deduced. Using these equations, the nonlinear free vibration and nonlinear forced response of the actuator are investigated. The effects of the van der Waals force on the nonlinear vibration of the flexible ring are analyzed. Results show that these effects of the van der Waals force are relatively obvious under some conditions and should be considered.     

Damage characteristics and surface description of near-wall materials subjected to ultrasonic cavitation

For the analysis of ultrasonic cavitation erosion on the surface of materials, the ultrasonic cavitation erosion experiments for AlCu4Mg1 and Ti6Al4V were carried out, and the changes of surface topography, surface roughness, and Vickers hardness were explored. Cavitation pits gradually expand and deepen with the increase of experiment time, and Ti6Al4V is more difficult to erode by cavitation than AlCu4Mg1. After experiments, the cavitation damage characteristics such as the single pit, the rainbow ring area, the fisheye pit, and some small pits were observed, which can be considered to be induced by a single micro-jet impact, ablation effect caused by the high temperature, micro-jet impingement with a sharp angle, and multibeam micro-jets coupling impact or negative pressure in the local area produced by micro-jet impact, respectively. The surface roughness and Vickers hardness of the material increase slowly after rapid growth at different points in time as the experiment time increases. With the increase of the ultrasonic amplitude, both of them first increase and then decrease after the ultrasonic amplitude is greater than 10.8 μm. The increases in surface roughness and Vickers hardness tend to decrease as the viscosity coefficient increases. Ultrasonic cavitation can cause submicron surface roughness and increase surface hardness by 20.36%, so it can be used as a surface treatment method.     

Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.