Flexural reinforcement of concrete floor slabs by carbon fiber textiles

The effect of carbon fiber textile for flexural reinforcement to deteriorated reinforced concrete floor slab is tested in laboratory by cutting out six specimens from existing structure aged more than 70 years. The repair method between concrete and carbon fiber textile is used as experimental parameter. From the test results, deformation, bond characteristic of carbon fiber textile and the applicability of carbon fiber textiles to flexural reinforcement of floor slabs are discussed.     

The Morphology and Mechanical Properties of Isotactic Polypropylene Injection-Molded Samples with the Presence of β-Nucleation Agent and Periodical Shear Field

The pressure vibration injection molding (PVIM) method was used to prepare β-nucleated isotactic polypropylene samples (PVIM β-iPP samples); a relatively low, periodical shear was imposed on the polymer melt in the mold at the filling and packing stages. The crystal structures and crystal orientation of the PVIM β-iPP samples were investigated by polarizing light microscopy (PLM), scanning electron microscopy (SEM), and synchrotron two-dimensional wide-angle X-ray diffraction (2D-WAXD). The PLM observations indicated that a cylindrite layer, rather than the transition layer, was found in PVIM β-iPP samples, which is different from the conventional injection-molded (CIM) samples. In addition, the thickness of the oriented layer of the PVIM samples was obviously greater than that of the CIM samples. The SEM observations demonstrated that a large amount of shish-kebab structures appeared in the shear layer of the PVIM β-iPP samples; at the same time, numerous β-spherulites were formed in the core layer. The 2D-WAXD data indicated that orientation homogeneity, to some degree, could be obtained by the periodical shear during PVIM. As a result, the above-mentioned morphology of the PVIM β-iPP samples leads to potentially useful prominent reinforcement and toughening of the material.     

A Comparative Study on the Reinforcing Effect of Aramide and PET Short Fibers in a Natural Rubber-Based Composite

Four types of chopped fibers have been studied as reinforcement additives in a standard natural rubber based, carbon black filled formulation. The fibers studied were aramide (2 types) and polyester (2 types). The chopped fibers were added on top of the carbon black filled rubber compound at 2, 4, and 8 phr levels. The extra reinforcing effect in the modulus, especially at low elongation, the increase in hardness, the anisotropic properties, and the stiffening effects have been studied together with the evaluation of the mechanical hysteresis in strain and in compression. The permanent set of the resulting rubber compounds have been evaluated as well. The best compromise in performances and price was found for a certain type of polyester fiber.     

Electron paramagnetic resonance investigation of molecular bond rupture due to ozone in deformed rubber

Electron paramagnetic resonance (EPR) provides a sensitive tool by which microscopic bond rupture can be monitored simultaneously with observations of macroscopic deformation and failure. Past techniques for studying fracture in semicrystalline polymers have been extended to investigate degradation of unfilled ruber in the presence of ozone. It was found that the rate of free radical production was linearly proportional to stretch ratio and ozone concentration and that stress relaxation and creep were not directly proportional to this production rate. The latter behavior was attributed to the particular dependence of crack density and growth on stress. It was concluded that at low strains, comparatively few surface cracks form; however, at higher strains, many more crack centers become active. Although many more surface cracks are present, they do not progress into the material as rapidly. Therefore, although more bonds were broken at higher strains and stresses, the stress relaxation rate and creep rates were not significantly increased.     

热致液晶共聚酯酰胺／PET共混物的流变性能和原位增强特性

采用Ｉｎｓｔｒｏｎ３２１１型毛细管流变仪研究了ＰＥＡ／ＰＥＴ共混物的流变性能，据此探讨共混物熔体的可纺性，讨论了共混物配比与复合纤维力学性能的关系，并且偏光显微镜，扫描电镜研究纤维的结构。结果表明，共混物的表观粘度低于ＰＥＴ的粘度，当ＰＥＡ为１０％，共混物的表观粘度达到最小值；且ＰＥＡ含量低于１０％时，共混物的可纺性即，表现出良好的原位增强效果。     

Study of ionizing radiation on the properties of polyamide 6 with fiberglass reinforcement

The use of polymers reinforced with fiberglass is becoming more and more common in the switches for household industries. These compounds perform a good tension resistance to the impact and the humidity absorption being used at the present time and also are in the automobile industry in parts underneath the hood, especially in the radiator frames. The aim of this work is to study the effect of ionizing radiation on the properties of polyamide 6 with fiberglass reinforcement and undergone to different irradiation doses. Samples were prepared and irradiated on JOB 188 accelerator with an electron beam energy of 1.5 MeV in air with different doses and a dose rate of 27.99 kGy/h. Afterward, the properties of the non-irradiated and irradiated polyamide 6 with fiberglass reinforcement were evaluated.     

Where Forward-Looking and Backward-Looking Models Meet

The present paper begins by deriving an instantaneous formulation for the backward-looking (reinforcement based learning) satisfaction balance model of Gray and Tallman (1984). This model is then used to generate interactional data from four simulated agents in a network interaction experiment. Because this initial model does not generate stable interaction structures in the network experiment, it is altered step by step in the direction of a forward-looking (agent with goals) model that has been shown to generate such stable interaction structures. The purpose of the modifications are to learn what aspects of the forward-looking model are needed to evolve a stable interaction structure, and to learn how these aspects may be incorporated into a model that remains essentially reinforcement based.