SnSxSe2-x单晶纳米片的可控制备与表征

锡二硫族化合物可以通过改变硫和硒的含量来连续调控三元合金材料的带隙、载流子浓度等物理化学性质,在电子和光电子器件应用上具有巨大的潜力。本文采用化学气相沉积(CVD)技术可控地制备了不同元素组分的SnS_xSe_2-x(x=0,0.2,0.5,0.8,1.0,1.2,1.5,1.8,2.0)单晶纳米片。采用扫描电子显微镜(SEM)、原子力显微镜(AFM)、能量色散X射线光谱(EDS)、透射电子显微镜(TEM)以及拉曼光谱等手段对SnS_xSe_2-x纳米片进行了综合表征。结果表明本方法成功实现了元素百分比可调的SnS_xSe_2-x单晶纳米片的可控制备。重点研究了依赖于元素百分比的SnS_xSe_2-x的拉曼特征谱,实验结果与基于密度泛函理论(DFT)的第一性原理计算得到的SnS_xSe_2-x的拉曼仿真谱高度吻合,理论计算结果较好地诠释了实验拉曼光谱发生变化的原因。本研究提供了一种元素百分比可调的三元SnS_xSe_2-x单晶纳米片的可控制备方法,同时对锡二硫族化合物的明确、无损识别提供了方案。     

石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Nanogenerators, as the typical conversion of mechanical energy to electrical energy devices, have great potential in the application of providing sustainable energy sources for powering miniature devices. In this work, cellulose acetate/cellulose nanocrystal(CA/CNC) composite nanofiber membranes were prepared by electrospinning method and then utilized to manufacture a flexible pressure-driven nanogenerator. The addition of CNC not only increased the content of piezoelectric cellulose I crystallization but also strengthened the mechanical deformation of the nanofiber membranes, which could greatly enhance the piezoelectric performance of CA/CNC composite membranes. The CA/CNC composite nanofiber membrane with 20%(mass fraction) of CNC(CA/CNC-20%) showed optimal piezoelectric conversion performance with the output voltage of 1.2 V under the force of 5 N(frequency of 2 Hz). Furthermore, the output voltage of the CA/CNC-20% nanogenerator device exhibited a linear relationship with applied impact force, indicating the great potential in pressure sensors.     

Optimization of biodiesel production via transesterification of soybean oil using α-MoO3 catalyst obtained by the combustion method

A catalyst based on MoO₃ was synthesized by a simple and fast pilot-scale combustion reaction method and applied to the conversion of soybean oil to biodiesel via transesterification. For that, the statistical analysis of the catalyst amount and temperature, factors that influence the process, was evaluated by means of central composite design 2². MoO₃ was characterized in terms of structure by X-ray diffraction (XRD), textural characterization Brunauer-Emmett-Teller (BET), density by helium pycnometry (DE), particle size analysis (DG) and acidity tests by temperature-programmed desorption of ammonia (NH₃-TPD), chemical analysis by X-ray fluorescence (EDX), morphology by scanning electron microscopy (SEM) and catalytic properties. The transesterification products were characterized by gas chromatography (GC), acidity index (AI) and kinematic viscosity (KV). The results indicate the catalyst formation with a surface area of 1.36 m²g^?1, and density of 4.5 g/cm³ which consists of a single crystalline phase of orthorhombic configuration, with total NH₃ acidity of 33.61 μ.mol/g. Morphological characterization revealed that the catalyst is formed by irregular plates of various sizes and shapes, with a wide sizes range of agglomerated particles. In the soybean oil transesterification reactions, the catalyst was active showing 96.9% conversion to ethyl esters. The experimental design was meaningful and predictive, with a reliability level of 95%. The statistical analysis identified temperature as a significant variable for the adopted planning. To conclude, a new single-phase catalyst (α-MoO₃) has been developed and successfully applied to the biodiesel Synthesis from soybean oil. These results have a positive and promising impact for biodiesel production by transesterification of soybean oil against ethanol.     

一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。     

雾化辅助化学气相沉积法氧化镓薄膜生长研究

采用自主设计搭建的雾化辅助化学气相沉积系统设备,开展了Ga₂O₃薄膜制备及其特性研究工作。通过X射线衍射研究了沉积温度、系统沉积压差对Ga₂O₃薄膜结晶质量的影响。结果表明,Ga₂O₃在425~650 ℃温度区间存在物相转换关系。随着沉积温度从425 ℃升高至650 ℃,薄膜结晶分别由非晶态、纯α-Ga₂O₃结晶状态向α-Ga₂O₃、β-Ga₂O₃两相混合结晶状态改变。通过原子力显微镜表征探究了生长温度对Ga₂O₃薄膜表面形貌的影响,从475 ℃升高至650 ℃时,薄膜表面粗糙度由26.8 nm下降至24.8 nm。同时,高分辨X射线衍射仪测试表明475 ℃、5 Pa压差条件下的α-Ga₂O₃薄膜样品半峰全宽仅为190.8″,为高度结晶态的单晶α-Ga₂O₃薄膜材料。     

Effect of oxygen on regulation of properties of moderately boron-doped diamond films

Regulation of oxygen on properties of moderately boron-doped diamond films is fully investigated. Results show that, with adding a small amount of oxygen (oxygen-to-carbon ratio < 5.0%), the crystal quality of diamond is improved, and a suppression effect of residual nitrogen is observed. With increasing ratio of O/C from 2.5% to 20.0%, the hole concentration is firstly increased then reduced. This change of hole concentration is also explained. Moreover, the results of Hall effect measurement with temperatures from 300 K to 825 K show that, with adding a small amount of oxygen, boron and oxygen complex structures (especially B₃O and B₄O) are formed and exhibit as shallow donor in diamond, which results in increase of donor concentration. With further increase of ratio of O/C, the inhibitory behaviors of oxygen on boron leads to decrease of acceptor concentration (the optical emission spectroscopy has shown that it is decreased with ratio of O/C more than 10.0%). This work demonstrates that oxygen-doping induced increasement of the crystalline and surface quality could be restored by the co-doping with oxygen. The technique could achieve boron-doped diamond films with both high quality and acceptable hole concentration, which is applicable to electronic level of usage.     

1,3,5-三(羧基甲氧基)苯镍配位聚合物的合成、晶体结构及性质研究

采用溶剂热法,1,3,5-三(羧基甲氧基)苯为定向配体和乙酸镍反应构筑了一个新型的金属配位聚合物[Ni(TB)₂(H₂O)₂]_n·2H₂O,其中H₃TB=1,3,5-三(羧基甲氧基)苯,通过元素分析、IR及X射线单晶衍射对配合物结构进行表征,并研究其荧光性质、热稳定性及Hirshfeld表面作用力。单晶结构分析表明,该配合物属于三斜晶系,空间群$P \overline{1}$,配合物中心离子Ni(Ⅱ)分别与来自两个水分子上的氧原子及四个不同1,3,5-三(羧基甲氧基)苯配体的羧酸氧原子配位,形成六配位的NiO₆八面体构型,并通过与1,3,5-三(羧基甲氧基)苯配体的氧原子配位不断延伸形成具有孔洞结构的一维链状构型。配合物具有良好的荧光性能和热稳定性。Hirshfeld表面作用分析表明配合物分子中O…H/H…O作用占主导且占比为39.0%,而H…H的作用力占比为25.9%,O…O的作用力占比为13.6%。     

不同退火条件对PEALD制备的Ga2O3薄膜特性的影响

利用等离子增强原子层沉积技术(PEALD)在c面蓝宝石衬底上制备了氧化镓(Ga₂O₃)薄膜,研究了退火气氛(v(N₂)∶v(O₂)=1∶1(体积比)、空气和N₂)及退火时间对Ga₂O₃薄膜晶体结构、表面形貌和光学性质的影响。研究结果表明,退火前的氧化镓处于亚稳态,不同退火气氛下退火后晶体结构发生明显改变,而且退火气氛中N₂比例增加有利于Ga₂O₃重结晶。在N₂气氛下退火达到30 min,薄膜结构已由亚稳态转变成择优取向的β-Ga₂O₃。而且表面形貌分析表明,退火30 min后表面形貌开始趋于稳定,表面晶粒密度不再增加。另外实验样品在 400~800 nm的平均透射率几乎是100%,且光吸收边陡峭。采用N₂气氛退火,对于富氧环境下沉积的Ga₂O₃更利于薄膜表面原子迁移,以及择优取向Ga₂O₃重结晶。