Partial-SOI high voltage P-channel LDMOS with interface accumulation holes

A new partial SOI (silion-on-insulator) (PSOI) high voltage P-channel LDMOS (lateral double-diffused metal-oxide semiconductor) with an interface hole islands (HI) layer is proposed and its breakdown characteristics are investigated theoretically. A high concentration of charges accumulate on the interface, whose density changes with the negative drain voltage, which increase the electric field (E_I) in the dielectric buried oxide layer (BOX) and modulate the electric field in drift region . This results in the enhancement of the breakdown voltage (BV). The values of E_I and BV of an HI PSOI with a 2-μm thick SOI layer over a 1-μm thick buried layer are 580V/μm and -582 V, respectively, compared with 81.5 V/μm and -123 V of a conventional PSOI. Furthermore, the Si window also alleviates the self-heating effect (SHE). Moreover, in comparison with the conventional device, the proposed device exhibits low on-resistance.     

THE ADAPTIVE IMMERSED INTERFACE FINITE ELEMENT METHOD FOR ELASTICITY INTERFACE PROBLEMS

In this paper, we propose adaptive finite element methods with error control for solving elasticity problems with discontinuous coefficients. The meshes in the methods do not need to fit the interfaces. We establish a residual-based a posteriori error estimate which is $λ$-independent multiplicative constants; the Lamé constant $λ$ steers the incompressibility. The error estimators are then implemented and tested with promising numerical results which will show the competitive behavior of the adaptive algorithm.     

飞行器供配电系统地面通用测试接口设计

供配电地面测试负责为飞行器提供模拟供电、控制状态切换、采集并传输系统状态信息,配合完成全飞行器全周期的综合测试任务。本文首先简要介绍了供配电地面测试系统的基本功能和设备组成,然后对供电、控制、测量的接口设计进行分析,最后提出接口通用化设计方案。本文为电气系统地面通用化测试研究提供了有益尝试。     

舰基遥测综合解调控制系统设计

遥测实时监控是保障试飞安全、提高试飞效率的重要手段。针对舰上特殊的试飞环境限制,现有遥测系统不能适应其任务需求,为完成某型号飞机舰上试飞任务,需要对现有遥测接收系统进行改进,以应对特殊试飞科目下对遥测信号的需求。采用跟踪接收机模块,并开发相应的解调模块,对系统设备进行远程控制解决了远距离数据传输的信号衰减问题;对遥测系统的自动温度控制大大提高了系统设备的环境适应性;通过接口转换实现模拟图像的网络输出、接收机模块和天线的网络串口转换,简化了信号接口类型,降低了信号传输的难度;从而实现小型化的舰基遥测综合解调控制系统设计。     

一种高清数字视频近眼立体显示系统设计

根据微型AM-OLED显示器的技术原理,提出了以双HDMI接口为视频输入接口、PIC16F1825为MCU控制芯片,以及双微型AM-OLED为显示器的立体显示系统的电路设计方案,主控芯片通过IIC串行总线对各模块寄存器进行配置。利用人眼的双目视差成像原理,通过配置HDMI解码芯片ADV7611和AM-OLED微显芯片的寄存器,使交错隔列立体视频源的奇数列和偶数列分离,视频源的奇数列和偶数列分别显示在左右眼相对应的AM-OLED显示器上,最终实现了立体显示。经测试,验证了系统方案的有效性。     

基于双模接口的测试系统设计

为了对飞行设备进行各种性能参数的测试,同时避免因环境因素而带来的数据传输不稳定的问题,使用双模接口(以太网接口与USB接口)实现上位机与测试系统的通信,通过对采样电路进行优化产生多路高精度信号并实时监测接收返回的群信号。经实验证明,系统完全可以完成各种环境中的功能测试,并提高了系统测试精度与传输数据的可靠性。     

基于无源超高频射频识别标签的湿度传感器设计

针对无源超高频射频识别传感器标签大规模运用的需求,采用中芯国际0.35μm互补金属氧化物半导体(CMOS)工艺设计并制造了一种低成本、低功耗的湿度传感器.湿度传感器单元采用聚酰亚胺作为感湿材料,利用顶层金属层制作叉指结构电极,制造过程与标准CMOS制造工序兼容,无需任何后处理工艺.接口电路部分基于锁相环原理,采用全数字电容.数字直接转换结构,能够工作在接近工艺阈值电压下.后期测试结果显示,该湿度传感器在常温下灵敏度为36.5 fF%RH,最大回滞偏差为7%,响应时间为20 ms,0.6 V电源电压下消耗2.1μW功率.     

基于模块计算机的千兆网磁共振谱仪控制接口

提出了一个基于模块计算机的磁共振谱仪的控制接口,它建立了核磁共振成像谱仪与上位计算机之间的通信,实现了控制谱仪、上传和下载、数据处理等功能,具备较高的传输速度,以及较好的实时性. 该接口以硬件模块的方式集成到谱仪上,通过千兆和百兆以太网连接上位机,接收下传至谱仪的序列;用中断机制和直接内存存取(DMA)方式实现与谱仪的数据传输,并将处理采集到的回波数据并上传到上位机. 控制接口的设计采用模块计算机Computer-On-Module(COM)的设计思路,以高性能的处理器为嵌入式平台,在Linux操作系统下开发驱动程序和应用程序. 实验证明,该模块具有数据处理速度快、传输速率高,成本低,体积紧凑,扩展性强等特点,是实现磁共振谱仪高性能的控制接口的理想方案.     

A moving screw dislocation near interfacial rigid lines in two dissimilar anisotropic media

This paper attempts to investigate the problem for the interaction between a uniformly moving screw dislocation and interface rigid lines in two dissimilar.anisotropic. materials. Integrating Riemann-Schwarz＇s symmetry principle with the analysis singularity of complex functions, we present the general elastic solutions of this problem and the closed form solutions for interfaces containing one and two rigid lines. The expressions of stress intensity factors, at the rigid line tips and image force acting on moving dislocation are derived explicitly. The results show that dislocation velocity has an antishielding effect on the rigid line tip and a larger dislocation velocity leads to the equilibrium position of dislocation closing with the rigid line. The presented solutions contain previously known results as the special cases.     

基于1553B总线的制导炸弹传递对准仿真系统

为了减少载机交联成本和提高研制效率,基于1553B总线,设计与实现了一个制导炸弹传递对准仿真研究系统.首先分析了1553B总线协议;然后介绍了该仿真系统的结构功能与实现,并对该仿真系统的硬件设计、1553B总线通讯接口设计、传递对准算法设计和主控软件流程设计进行了论述;最后对该仿真系统进行地面跑车试验.试验结果表明,对准完成后惯导的姿态角误差得到了有效的修正,从而证明该仿真系统的设计是成功的.该系统已在某型号项目的研制中得到了成功的应用.