基于NiCo2O4纳米片电极的非对称混合电容器

The looming global energy crisis and ever-increasing energy demands have catalyzed the development of renewable energy storage systems. In this regard, supercapacitors (SCs) have attracted widespread attention because of their advantageous attributes such as high power density, excellent cycle stability, and environmental friendliness. However, SCs exhibit low energy density and it is important to optimize electrode materials to improve the overall performance of these devices. Among the various electrode materials available, spinel nickel cobaltate (NiCo₂O₄) is particularly interesting because of its excellent theoretical capacitance. Based on the understanding that the performances of the electrode materials strongly depend on their morphologies and structures, in this study, we successfully synthesized NiCo₂O₄ nanosheets on Ni foam via a simple hydrothermal route followed by calcination. The structures and morphologies of the as-synthesized products were characterized by X-ray diffraction, scanning electron microscopy, and Brunauer-Emmett-Teller (BET) surface area analysis, and the results showed that they were uniformly distributed on the Ni foam support. The surface chemical states of the elements in the samples were identified by X-ray photoelectron spectroscopy. The as-synthesized NiCo₂O₄ products were then tested as cathode materials for supercapacitors in a traditional three-electrode system. The electrochemical performances of the NiCo₂O₄ electrode materials were studied and the area capacitance was found to be 1.26 C·cm^-2 at a current density of 1 mA·cm^-2. Furthermore, outstanding cycling stability with 97.6% retention of the initial discharge capacitance after 10000 cycles and excellent rate performance (67.5% capacitance retention with the current density from 1 to 14 mA·cm^-2) were achieved. It was found that the Ni foam supporting the NiCo₂O₄ nanosheets increased the conductivity of the electrode materials. However, it is worth noting that the contribution of nickel foam to the areal capacitance of the electrode materials was almost zero during the charge and discharge processes. To further investigate the practical application of the as-synthesized NiCo₂O₄ nanosheets-based electrode, a device was assembled with the as-prepared samples as the positive electrode and active carbon (AC) as the negative electrode. The assembled supercapacitor showed energy densities of 0.14 and 0.09 Wh·cm^-3 at 1.56 and 4.5 W·cm^-3, respectively. Furthermore, it was able to maintain 95% of its initial specific capacitance after 10000 cycles. The excellent electrochemical performance of the NiCo₂O₄ nanosheets could be ascribed to their unique spatial structure composed of interconnected ultrathin nanosheets, which facilitated electron transportation and ion penetration, suggesting their potential applications as electrode materials for high performance supercapacitors. The present synthetic route can be extended to other ternary transition metal oxides/sulfides for future energy storage devices and systems.     

改性二氧化硅纳米颗粒提高二氧化碳泡沫稳定性的研究

通过纳米二氧化硅的硅烷化改性, 使其在高矿化度盐水中可以稳定存在的前提下, 研究了改性纳米颗粒与阳离子表面活性剂十二烷基三甲基氯化铵混合体系的溶液稳定性及协同稳定CO₂泡沫的效果. 研究结果表明, 无机盐离子对改性纳米颗粒与阳离子表面活性剂间的静电吸引力具有屏蔽作用, 且矿化度越高, 屏蔽效果越明显, 从而混合溶液更易于在高盐水中稳定; 纳米颗粒表面的活性剂吸附层受二者浓度的影响, 进而影响了颗粒的亲/疏水性; 当混合体系中的表面活性剂浓度低于临界胶束浓度(CMC)时, 混合溶液与CO₂的界面张力高于单独活性剂溶液, 而当活性剂浓度高于CMC时, 对CO₂-溶液界面张力几乎无影响, 最低界面张力可降至6 mN/m左右; 改性纳米颗粒的加入可以进一步提高CO₂体相泡沫半衰期一倍以上, 但受二者浓度比例的影响; 纳米颗粒的加入有效提高了多孔介质中泡沫的表观黏度, 最大增幅由20 mPa·s增至55 mPa·s左右, 泡沫黏度增加接近3倍, 增强了CO₂泡沫驱的封堵作用.     

时程稳定性系数确定的边坡逐孔起爆孔间微差降振时间

为了获得边坡逐孔爆破最佳降振微差时间，以某个实际边坡逐孔微差爆破施工现场为原型，先利用ANSYS建立二维静态模型，借助有限元折减法确定自然状态下的潜在滑动面和静态安全系数；基于已确定的二维潜在滑动面重新建立同尺寸同性质的三维逐孔微差爆破动态模型，利用LS-DYAN进行动力分析，整个过程分别设置同排3个炮孔0、17、25、42和65 ms等5种不同孔间微差起爆方式；同时，对该施工现场进行排、孔间（25 ms，17 ms）、（25 ms，25 ms）、（25 ms，42 ms）、（25 ms，65 ms）等4种微差时间控制的等比例相似小炮测振实验。提取模拟结果中3个炮孔同时起爆时滑面单元的应力数值代入极限平衡法计算公式，绘制了冲击载荷作用下边坡稳定性系数曲线，通过对曲线的理论分析发现，最佳降振微差时间约为48 ms；而三维数值模拟和测振实验结果均显示，孔间微差时间取42 ms时降振效果较佳。这说明，边坡稳定性系数曲线给出的微差时间与模拟和实验结果较为接近，可为今后边坡逐孔微差爆破降振研究提供参考。     

一种具有低振动灵敏度和宽动态范围的MEMS陀螺仪(英文)

为了进一步提高MEMS陀螺的动态范围和振动环境适应性,以加速其工程化应用步伐,研究了陀螺振动误差,提出了一种新型MEMS陀螺结构。MEMS陀螺仍然采用了音叉结构形式,同时采用了工字型框架和隔离结构,从而提高了陀螺结构的稳定性和抗振动性能,并降低了残余应力对陀螺影响。理论分析了驱动和检测模态频差对标度因数非线性的影响,并基于理论和实验分析了振动环境中的角振动对陀螺性能的影响。在此基础上,进行了陀螺的模态优化设计,以进一步减小了陀螺的振动灵敏度,并使其具有大动态范围。MEMS陀螺采用了SOI圆片制备,并采用了圆片级真空封装技术实现陀螺芯片的真空封装。MEMS陀螺芯片和ASIC芯片叠装在陶瓷管壳内,体积为11.4?11.4?3.8 mm3。实验结果表明,MEMS陀螺的测量范围为±7200 (°)/s,零偏稳定性为12.2 (°)/h(1σ)。随机振动环境下(7.6grms),该陀螺的振中零偏变化量小于10.0 (°)/h,振中的零偏稳定性小于24.0 (°)/h,是原陀螺的1/5。     

一维非等温可压缩Navier-Stokes-Korteweg方程组稀疏波的整体稳定性（英文）

可压缩Navier-Stokes-Korteweg方程组可用来描述具有内部毛细作用的粘性可压缩流体的运动.本文研究了毛细系数依赖于密度、粘性系数和热传导系数依赖于温度的一维非等温的可压缩Navier-Stokes-Korteweg方程组Cauchy问题解的大时间行为.利用基本的L~2能量方法,我们证明如果相应的Euler方程组的黎曼问题存在稀疏波解,那么所考虑的一维可压缩Navier-Stokes-Korteweg方程组存在唯一的整体强解,并且当时间趋于无穷大时,此强解趋向于稀疏波.这里初始扰动和稀疏波的强度都可以任意大.     

含分布时滞的时滞微分系统多步龙格-库塔方法的时滞相关稳定性

本文研究了一类含分布时滞的时滞微分系统的多步龙格-库塔方法的稳定性.基于辐角原理，本文给出了多步龙格-库塔方法弱时滞相关稳定性的充分条件，并通过数值算例验证了理论结果的有效性.     

非Fourier温度场分布的奇摄动解

应用非Fourier热传导定律构建了单层材料中温度场模型，即一类在无界域上带小参数的奇摄动双曲方程，通过奇摄动展开方法，得到了该问题的渐近解.首先应用奇摄动方法得到了该问题的外解和边界层矫正项，通过对内解和外解的最大模估计和关于时间导数的最大模估计以及线性抛物方程理论，得到了内外解的存在唯一性，从而得到了解的形式渐近展开式.通过余项估计，给出了渐近解的L2估计，得到了渐近解的一致有效性，从而得到了无界域上温度场的分布.通过奇摄动分析，给出了非Fourier 温度场与Fourier 温度场的关系，描述了非Fourier温度场的具体形态.     

广义强向量拟均衡问题解集的通有稳定性

研究广义强向量拟均衡问题(GSVQEP)解集的通有稳定性.在约束集值映射满足一定连续与目标映射是锥-真拟凸的集值映射条件下,证明了广义强向量拟均衡问题构成的空间M中,在Baire分类意义下,广义强向量拟均衡问题解集是通有稳定的,且给出了空间M中对每个广义强向量拟均衡问题的解集至少存在一个本质连通区.     

求解分数阶延迟微分方程的卷积Runge-Kutta方法

本文利用强A-稳定Runge-Kutta方法求解一类非线性分数阶延迟微分方程初值问题,并给出了算法的稳定性和误差分析.数值算例验证算法的有效性及其相关理论结果.