评价表面活性剂溶液泡沫性能的方法—真球气泡法北大核心CSCD

通过真球气泡法测定了不同价数和浓度的无机盐体系下十二烷基硫酸钠(SDS)表面活性剂溶液的表面张力和表面扩展黏度;通过Ross-Miles法测定了相应同一溶液的发泡力和泡沫稳定性;结果表明:SDS溶液的表面张力值随着各种无机盐浓度的增加而减小至不变,此时的无机盐浓度作为相对浓度100%来考察时,发现临界胶束浓度(CMC)值与添加盐的种类无关,只随无机盐的相对浓度的增加而减少;即CMC值随着无机盐的相对浓度的增加从不含无机盐时的8.3 mmol/L均收敛至最小值3.0 mmol/L;表面张力值和对应的发泡力值呈负线性关系,由此推断表面张力值可以评价发泡力;表面扩展黏度值和对应的泡沫稳定性值呈正线性关系,由此推断表面扩展黏度可以评价泡沫稳定性;无机盐种类对SDS表面活性剂发泡力和泡沫稳定性的影响力随阳离子价数(Na^(+)、Cu^(2+)、Fe^(3+))增加而增加。     

新型磺基甜菜碱/聚丙烯酰胺体系表面及界面性能

采用自制的新型磺基甜菜碱两性表面活性剂与相对分子质量2500万的聚丙烯酰胺进行复配,考察了不同温度和矿化度条件下,聚合物对复配溶液表面、界面性能的影响。 采用滴体积法测定了溶液的表面张力,结果表明,加入聚合物使溶液的临界胶束浓度增大,且复配溶液的表面张力大于单独表面活性剂溶液的表面张力。 当聚合物浓度一定,增大溶液矿化度时,体系表面张力增大。 用旋滴型界面张力仪测定了溶液的界面张力,结果表明,增大聚合物浓度,油水界面张力增大,增大溶液矿化度,油水界面张力有所升高。 聚合物质量浓度为1.5 g/L,表面活性剂质量浓度为0.3 g/L时,可使胜利油田孤岛原油和孤东原油的油水界面张力达到超低数量级（10-3 mN/m）。 用分水时间法测定了溶液的乳化性能,结果表明,聚合物浓度增大,分水时间延长,并考察了75、85和95 ℃条件下体系的乳化性能,温度越高,分水时间越短。     

光敏型季铵盐类阳离子表面活性剂的合成及表面活性和泡沫性质

本文报道了一种光敏型的阳离子表面活性剂（AZO），其分子结构中含有偶氮苯基团，并研究了光照对表面活性和泡沫性能的影响。经紫外光照射后，表面活性剂的饱和吸附量（Г_max）减小，临界胶束浓度（cmc）、最低表面张力（γ_cmc）和分子极限占有面积（A_min）增大；气泡数目增多，直径变小，发泡能力和泡沫稳定性降低。实验结果证实，该表面活性剂的表面活性和泡沫稳定性可以用光照进行调控。     

Gemini表面活性剂/C12En混合体系的界面吸附、扩张粘弹与泡沫稳定性

用表面张力法研究了阳离子gemini表面活性剂乙基-1, 2-双(十二烷基二甲基溴化铵)(简写为12-2-12)和非离子表面活性剂十二烷基聚氧乙烯醚(C₁₂E_n,其中n = 4, 10, 23)混合体系在气液界面上的吸附行为;用扩张流变技术研究了吸附膜的扩张粘弹行为,实验数据用Lucassen-van den Tempel (LVT)模型进行拟合并根据模型得到了极限弹性值.最后研究了混合体系的泡沫行为,用泡沫塌陷到初始高度一半所对应的时间(t_1/2)来表征泡沫的稳定性.结果表明,所有的非离子表面活性剂C₁₂E_n均与12-2-12产生了吸引作用.在12-2-12浓度相同的情况下,混合吸附层中吸附分子的最小分子占据面积的顺序为12-2-12/C₁₂E₂₃ > 12-2-12/C₁₂E₁₀ > 12-2-12/C₁₂E₄,而极限弹性的顺序为ε_{0, fit}(12-2-12/C₁₂E₄) > ε_{0, fit}(12-2-12/C₁₂E₁₀) > ε_{0, fit}(12-2-12/C₁₂E₂₃).与单组分12-2-12形成的吸附膜相比,只有12-2-12/C₁₂E₄形成更加紧密的结构.具有较小亲水头基的非离子表面活性剂C₁₂E₄的加入,可增强12-2-12吸附膜的弹性,进而增强了对应体系泡沫的稳定性.     

支链化甜菜碱和阳离子表面活性剂在聚甲基丙烯酸甲酯表面的吸附及其润湿性质

利用座滴法研究了两性离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基羧酸甜菜碱(n = 0, 3)和阳离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基季铵盐溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质,考察了表面活性剂类型、结构及浓度对接触角的影响趋势。研究发现,表面活性剂浓度低于临界胶束浓度(cmc)时,分子通过氢键以平躺的方式吸附到PMMA界面,亲水基团靠近固体界面, PMMA表面被轻微疏水化;表面张力和粘附张力同时降低,导致此阶段接触角随浓度变化不大。浓度高于cmc时,表面活性剂通过疏水作用吸附,亲水基团在外, PMMA表面被明显亲水改性,接触角随浓度升高显著降低。由于具有相同的支链烷基,表面活性剂类型变化和聚氧乙烯基团的引入对接触角影响不大。     

支链醇对Gemini表面活性剂表面活性和胶束化行为的影响

Gemini表面活性剂是一类高效的新型表面活性剂,而醇是工业界和日化领域最常采用的表面活性剂助剂,因此研究不同结构的醇对Gemini表面活性剂表面活性和胶束化行为的影响规律和机理对于促进Gemini表面活性剂的发展和实际应用具有重要意义.利用表面张力、电导、等温滴定微量热,低温透射电镜和核磁共振研究了直链醇1-戊醇和具有相同主链的支链醇2-己醇与3-庚醇对具有不同长度连接基团阳离子季铵盐型Gemini表面活性剂C₁₂C_SC₁₂Br₂ （S=2,4,6,8,10,12）的表面活性和胶束化行为的影响,结果发现,支链醇能够显著影响表面活性剂在气/液界面的排布,使得C₂₀ （使溶剂的表面张力降低20 mN/m所需的表面活性剂浓度）和γ_CMC （CMC时表面张力值）随醇支化度的增加而显著降低,而支链醇对表面活性剂在溶液中的临界胶束浓度以及胶束的尺寸和形貌均没有明显影响,同时这些醇对Gemini表面活性剂的影响与连接基团的长度相关.阐述了上述结果产生的机理,将有助于指导如何选择合适结构的醇助剂去调控Gemini表面活性剂的表面和溶液性质.     

CO2开关型溶剂、溶质及表面活性剂*

CO₂诱导的开关型溶剂、溶质及表面活性剂是指在通入和排出CO₂后,其溶液性质能发生可逆变化的新型溶剂、溶质及表面活性剂,是典型的环境刺激响应型智能化合物。本文综述了CO₂诱导的开关型溶剂、溶质及表面活性剂的结构、性能及研究进展,并指出了这些开关型溶剂、溶质及表面活性剂的发展方向及应用前景等。     

阴离子孪连表面活性剂的合成及其表/界面活性研究

合成了疏水链长度不同和连接基长度不同的7种系列阴离子孪连表面活性剂,研究了它们的表/界面活性。结果表明,它们有较低的表面张力和临界胶束浓度(CMC),有很好的表面活性。它们的CMC都在10-5~10-6mol/L之间,表面张力在26·5~34mN/m之间。它们有非常好的抗一价、二价盐的能力。除了C16-C2-C16在高于5%的NaCl溶液中会产生析出外,其余孪连表面活性剂都能耐盐20%以上。随着盐浓度的增加,孪连表面活性剂与烷烃间的界面张力逐渐降低,能达到10-3mN/m。与中原油田原油间的界面张力能降低到10-3~10-4mN/m,表明它们可应用于特高矿化度油藏提高采收率。     

高盐油藏下两性/阴离子表面活性剂协同获得油水超低界面张力

研究了在高盐油藏中, 利用两性/阴离子表面活性剂的协同效应获得油水超低界面张力的方法. 两性表面活性剂十六烷基磺基甜菜碱与高盐矿化水具有很好的相容性, 但在表面活性剂浓度为0.07%-0.39%(质量分数)范围内仅能使油水界面张力达到10^-2 mN·m^-1量级, 加入阴离子表面活性剂十二烷基硫酸钠后则可与原油达到超低界面张力. 通过探讨表面活性剂总浓度、金属离子浓度、复配比例对油水动态界面张力的影响, 发现两性/阴离子表面活性剂混合体系可以在高矿化度、低浓度和0.04%-0.37%的宽浓度范围下获得10^-5 mN·m^-1量级的超低界面张力, 并分析了两性/阴离子表面活性剂间协同获得超低界面张力的机制.     

C12-m-C12型阳离子Gemini表面活性剂在煤沥青表面的润湿性

利用座滴法和电泳法研究了阳离子Gemini表面活性剂C₁₂-m-C₁₂·2Br^-(m=4、6、8、10)在煤沥青表面的润湿性质及吸附机理。结果表明, 表面张力均随表面活性剂浓度的增大而减小, 超过临界胶束浓度(CMC)后趋于平稳, 接触角θ和铺展系数S的变化趋势与表面张力类似; 在所研究浓度范围内,C₁₂-10-C₁₂型表面活性剂的γ_lg~cosθ曲线符合Zisman理论, 且侵湿功(W_i)与表面张力也呈线性关系; 煤沥青表面的Zeta电位随表面活性剂浓度的增加从负电变为正电,最后趋于平稳, 且零电位对应的浓度比CMC至少低一个数量级; C₁₂-8-C₁₂型Gemini表面活性剂能显著改变煤沥青表面的润湿性. 由Gemini表面活性剂在煤沥青表面润湿结果及Zeta电位可以看出, C₁₂-m-C₁₂型Gemini表面活性剂在煤沥青表面的润湿是静电作用和范德华吸附共同作用的结果; 润湿过程可分为三个阶段。     

Synergistic improvement of foam stability with SiO2 nanoparticles (SiO2-NPs) and different surfactants

Foam fluids are widely used in petroleum engineering, but long-standing foam stability problems have limited the effectiveness of their use. The study explores the synergistic effects and influencing factors of SiO₂ nanoparticles (SiO₂-NPs) with different wettability properties and three different surfactants. The paper investigates the foaming performance of different types of surfactants and analyzes and compares the stability of foam after adding hydrophilic and hydrophobic SiO₂-NPs from macroscopic as well as microscopic perspectives, and the effects of temperature and inorganic salts on the stability of mixed solutions. The experimental results show that: 1) hydrophilic nanoparticles can significantly enhance the foam stability of amphoteric surfactants, with a small increase in the foam stability of anionic and cationic surfactants; 2) The concentration of nanoparticles did not have a significant effect on the stability of the cationic surfactants and this conclusion was verified in the experimental results of the surface tension measured below;3) The cationic surfactants showed better temperature resistance at temperatures of 50–90 °C. Both amphoteric surfactant solutions with the addition of hydrophilic SiO₂-NPs or hydrophobic SiO₂-NPs significantly improved the temperature resistance of the foam at high temperatures. The anionic surfactant solution with hydrophobic SiO₂-NPs did not enhance the solution temperature resistance; 4) The surface tension of the surfactant solution gradually increases with increasing concentration of hydrophilic or hydrophobic SiO₂-NPs and then levels off; 5) the hydrophilic SiO₂-NPs had a significant effect on the salt tolerance of the anionic and amphoteric surfactant solutions. The salt tolerance of cationic surfactant solutions with hydrophobic SiO₂-NPs was better than that of surfactants with hydrophilic SiO₂-NPs.     

Rheology and high-temperature stability of novel viscoelastic gemini micelle solutions

To broaden the application of clean fracturing fluid based on surfactant, a gemini cationic C₂₅-tailed surfactant, called FL-25, was synthesized. FL-25 can form a wormlike viscoelastic fluid in aqueous solution without adding any organic or inorganic salts. The rheological properties and thermal stability of the novel gemini micelle solutions were further investigated. The results show that the gemini micelle solution possesses viscoelasticity, thixotropy, and shear-thinning properties. The apparent viscosity of the viscoelastic gemini micelle solution at a shear rate of 170?s^?1 remains approximately 69?mPa?·?s at 110°C for 90 minutes, showing good high-temperature-resistance property. FL-25 may be a novel gemini surfactant applied in clean viscoelastic surfactant fracturing fluids in the oil and gas field.     

Enhancing cellulase foam fractionation with addition of surfactant

Foam fractionation cannot be used to recover cellulase from an aerated water solution effectively because cellulase by itself can produce only a small amount of foam. The addition of a surfactant can, however, increase the foamate volume and enhance the concentration of cellulase. We studied three detergents individually added to a 200 mg/L cellulase solution to promote foaming. These detergents were anionic, cationic, and nonionic surfactants, respectively. Although contributing to foam production, it was observed that nonionic surfactant (Pluronic F-68) barely concentrated cellulase, leaving the enrichment ratio unchanged, near 1. With anionic surfactant, sodium dedecyl sulfate, and cationic surfactant, cetyltrimethylammonium bromide (CTAB), the enrichment ratio became much larger, but cellulase denaturation occurred, reducing the activity of the enzyme. When CTAB was used to help foam cellulase, β-cyclodextrin was subsequently added to the foamate to help restore the enzyme activity.     

On the Origin of Foam Stability: Understanding from Viscoelasticity of Foaming Solutions and Liquid Films

The foam stability (drainage half-life) of α-olefin sulfonate (AOS) with partially hydrolyzed polyacrylamide (HPAM) or xanthan gum (XG) solution was evaluated by the Warring Blender method. With the increase of polymer (HPAM or XG) concentration, foam stability of the surfactant–polymer complexes increased, and the drainage half-life of AOS-XG foam was higher than that of AOS-HPAM foam at the same polymer and surfactant concentration. With the addition of polymer (HPAM or XG), the viscoelasticity of bulk solution and the liquid film were enhanced. The viscoelasticity of AOS-XG bulk solution and liquid film were both higher than that of AOS-HPAM counterparts.      

Effects of a Novel Organic Alkali on the Interfacial Tension and Emulsification Behaviors Between Crude Oil and Water

Experiments have been carried out to investigate the interfacial tension (IFT) and emulsification behaviors between Shengli crude oil and a novel organic alkali (OA). The dynamic IFT and minimum IFT are adopted to characterize the IFT behaviors; the microscopic method, Turbiscan stability index, separated water rate, and laser particle size analysis method are used to show the emulsification behaviors. The dynamic and minimum IFT both decrease continuously with the increase of OA concentration whether surfactant is added or not; because of the synergy of OA and surfactant, the minimum IFT will be reduced to the ultralow value. The synergy is also crucial for the crude oil emulsification. When OA and surfactant are used together, owing to the mosaic and cross-multiple adsorption of OA, surfactant and in situ soap at the interfacial film, the oil can be emulsified more easily, the quantity of emulsified droplets is higher, and the emulsion is more stable with OA concentration increases. The relationship of the minimum IFT and emulsification is investigated; it indicates that the emulsion stability improves, the degree of dispersed homogeneity of oil droplets increases, and the median diameter of emulsified oil droplets decreases with the decline of the minimum IFT.     

Foaming and foam stability for mixed polymer-surfactant solutions: effects of surfactant type and polymer charge

Solutions of surfactant-polymer mixtures often exhibit different foaming properties, compared to the solutions of the individual components, due to the strong tendency for formation of polymer-surfactant complexes in the bulk and on the surface of the mixed solutions. A generally shared view in the literature is that electrostatic interactions govern the formation of these complexes, for example between anionic surfactants and cationic polymers. In this study we combine foam tests with model experiments to evaluate and explain the effect of several polymer-surfactant mixtures on the foaminess and foam stability of the respective solutions. Anionic, cationic, and nonionic surfactants (SDS, C(12)TAB, and C(12)EO(23)) were studied to clarify the role of surfactant charge. Highly hydrophilic cationic and nonionic polymers (polyvinylamine and polyvinylformamide, respectivey) were chosen to eliminate the (more trivial) effect of direct hydrophobic interactions between the surfactant tails and the hydrophobic regions on the polymer chains. Our experiments showed clearly that the presence of opposite charges is not a necessary condition for boosting the foaminess and foam stability in the surfactant-polymer mixtures studied. Clear foam boosting (synergistic) effects were observed in the mixtures of cationic surfactant and cationic polymer, cationic surfactant and nonionic polymer, and anionic surfactant and nonionic polymer. The mixtures of anionic surfactant and cationic polymer showed improved foam stability, however, the foaminess was strongly reduced, as compared to the surfactant solutions without polymer. No significant synergistic or antagonistic effects were observed for the mixture of nonionic surfactant (with low critical micelle concentration) and nonionic polymer. The results from the model experiments allowed us to explain the observed trends by the different adsorption dynamics and complex formation pattern in the systems studied.     

Enhanced heavy oil recovery by organic alkali combinational flooding solutions

Although alkaline/surfactant/polymer (ASP) flooding is successfully applied in oil fields, some disadvantages such as scales, corrosion effects, and viscosity reductions of polymer solutions appear. Usage of organic alkalis can avoid or decrease these disadvantages. In this paper, the physicochemical properties, including interfacial tension (IFT), and viscosity, of organic alkali combinational flooding solutions and their effectiveness as enhanced oil recovery agents are investigated. Monoethanolamine (MEA) is the optimal one for decreasing the IFT among the three organic alkalis studied in this paper. Although MEA cannot decrease the IFT as low as NaOH does, it has good compatibility with both surfactant and the polymer hydrolyzed polyacrylamide (HPAM). MEA not only helps a surfactant solution or HPAM/surfactant mixture attain ultralow IFT values, but can also promote better viscosity stability for HPAM or HPAM/surfactant solutions compared to NaOH. Moreover, core flood experiments show that adding MEA can obtain additional tertiary oil recovery of 6%–10% original oil in place (OOIP) on the top of HPAM or HPAM/surfactant flooding, although MEA has a lower enhanced oil recovery than NaOH. The experimental results show that MEA is a good choice to replace NaOH in enhancing heavy oil recovery.     

Change of Surface Structure upon Foam Film Formation

The charge distribution and coverage with surfactant molecules at foam film surfaces plays an important role in determining foam film structure and stability. This work uses the concentration depth profiling technique neutral impact collision ion scattering spectroscopy to experimentally observe the charge distribution in a foam film for the first time. The charge distribution at the surface of a foam film and the surface of the corresponding bulk liquid were measured for a cationic surfactant solution and the surface excess as well as the electric potential were determined. Describing the internal pressure of foam films by using the electrochemical potential is introduced as a new concept. The foam film can be seen to have a more negative surface charge compared to the bulk liquid surface due to re‐arranging of the surfactant molecules. It is discussed how the change in surface excess and electric potential change the electrochemical potential and the stability of the foam film.     

Foams stabilized by mixed cationic gemini/anionic conventional surfactants

The mixed adsorption of a cationic gemini surfactant, ethanediyl-1,2-bis(dodecyldimethylammonium bromide) (abbreviated as 12-2-12), and an anionic conventional surfactant, sodium dodecyl sulfate (SDS), was examined using surface tension measurements. The viscoelastic properties of the mixed films were investigated by dilational interfacial rheology technique. The results showed that the addition of SDS promoted the close packing of adsorbed molecules at the interface, which increased the dilational elasticity of the mixed films. The stability of the foams was determined by the half-life of foam height collapse. The foams generated by 12-2-12/SDS mixtures were more stable than that formed by pure 12-2-12. In the presence of sodium bromide, the foam stability was further enhanced and the surfactant concentration required to attain the maximum effect in stabilizing foams was greatly reduced. The high foam stability could well relate to the high elasticity of the film.