碳纳米管上原位沉积钯-钴-镍纳米颗粒及其对乙醇氧化的电活性

以水合肼为还原剂,在水和乙醇的混合溶液中制备多壁碳纳米管(MWCNT)负载的纳米镍(Ni/MWCNT)和纳米镍钴(Ni-Co/MWCNT)颗粒,然后将它们分别与氯化钯溶液反应,形成的钯纳米颗粒原位沉积在MWCNT表面,从而得到MWCNT负载的Pd-Ni/MWCNT和Pd-Ni-Co/MWCNT催化剂。SEM和TEM图像显示,MWCNT上的催化剂颗粒是由5~10 nm的小颗粒团聚而成的30~100 nm的大颗粒,三金属催化剂的粒径比双金属的粒径小,在MWCNT上的分散度更高。ICP和EDS分析显示,Pd直接还原并包覆在纳米镍和纳米镍钴表面;采用循环伏安和计时电流技术,研究了催化剂在碱性溶液中对乙醇氧化的电催化活性,结果表明,Pd-Ni-Co/MWCNT催化剂对乙醇氧化具有强的电催化活性,乙醇氧化对应的峰电流密度达101.8 mA·cm^-2,并且催化剂催化活性稳定。     

Cu/Ni助催化剂对TiO2光催化制取苯酚性能的影响

以TiO₂纳米粒子为主催化剂, 采用“浸渍-还原法”构筑了铜、镍共负载的二氧化钛基光催化系统。以苯为起始原料, H₂O₂为氧化剂, 研究了Cu/Ni助催化剂对TiO₂可见光催化制取苯酚性能的影响并对Cu/Ni助催化剂的作用机制进行了探讨。结果表明, 在可见光照射下, 纯TiO₂纳米粒子对苯氧化制取苯酚反应没有催化活性。铜、镍的引入可以明显地增强TiO₂可见光催化制取苯酚的活性。当使用负载有铜、镍的TiO₂作为催化剂时, 苯酚的产率可达到18%。结果还表明Cu、Ni之间存在着很强的协同作用。在该协同作用下, Cu、Ni共负载的TiO₂纳米粒子表现出了较单一金属负载的TiO₂纳米粒子高得多的光催化活性。     

由不同镍盐前体制备高分散Ni/SBA-15催化剂：活化氛围的影响

以硝酸镍和乙酸镍为镍前体,用浸渍法分别在空气和氢气氛围活化制得系列Ni/SBA-15催化剂,通过XRD、H₂-TPD、N₂物理吸附和在线质谱等物理化学手段对催化剂进行了表征,并结合微型高压反应釜萘加氢反应,评价了催化剂的加氢性能。结果表明,氢气氛围活化对硝酸镍为镍前体所制Ni/SBA-15催化剂的镍分散度和活性有显著促进作用,而空气氛围活化对乙酸镍为镍前体所制催化剂有明显促进作用。根据催化剂前体在不同氛围活化时的热分解产物,提出了活化氛围对不同镍前体制得Ni/SBA-15催化剂所产生的作用机理。     

Benign synthesis of N-(8-quinolyl)pyridine-2-carboxamide) ligand (Hbpq), and its Ni (II) and Cu (II) complexes. A fluorescent probe for direct detection of nitric oxide in acetonitrile solution based on Hbpq copper(II) acetate interaction

The ligand Hbpq = N-(8-quinolyl)pyridine-2-carboxamide) has been prepared using tetrabutylammonium bromide (TBAB) as an environmentally friendly reaction medium. Four new complexes of this ligand, [M(bpq)X] (M = Cu(II), X = SCN̄ (1), N₃̄ (2); M = Ni(II), X = SCN̄ (3), N₃̄ (4)), have also been synthesized and fully characterized. The crystal and molecular structures of [Cu(bpq)(NCS)]_n (1) have been determined by X-ray crystallography. Copper(II) ion adopts a distorted square pyramidal (4 + 1) coordination in this complex. Hbpq ligand shows a strong emission at 500 nm in acetonitrile solution. The emission is quenched in the presence of copper(II) acetate, apparently because of the formation of [Cu(L)(OAc)(H₂O)] complex. Introduction of nitric oxide (NO) into the acetonitrile solution at room temperature induces an increase in the fluorescence intensity, presumably due to the reduction of Cu(II) to Cu(I). This process is reversible and can form a basis for direct detection of NO.     

Ni2P-NiS双助剂促进g-C3N4光催化产氢动力学

本文通过简单的一步水热法得到Ni₂P-NiS双助催化剂,之后采用溶剂蒸发法将Ni₂P-NiS与g-C₃N₄纳米片结合构建获得无贵金属的Ni₂P-NiS/g-C₃N₄异质结。研究结果表明,优化后的复合材料具有良好的光催化产氢活性,其产氢速率最高可到6892.7 μmol·g^-1·h^-1,分别为g-C₃N₄ (150 μmol·g^-1·h^-1)、15%NiS/g-C₃N₄ (914.5 μmol·g^-1·h^-1)和15%Ni₂P/g-C₃N₄ (1565.9 μmol·g^-1·h^-1)的46.1、7.5和4.4倍。这主要归因于Ni₂P-NiS相比Ni₂P和NiS单体具有更好的载流子转移能力,其与g-C₃N₄形成的肖特基势垒能有效促进光生载流子在二者界面上的分离,同时Ni₂P-NiS能进一步降低析氢过电势,进而显著增强了表面析氢反应动力学。本研究为开发稳定、高效的非贵金属产氢助剂提供了实验基础。     

Raney Ni催化生物基糠醛还原胺化合成糠胺

生物质衍生物糠醛还原胺化是合成糠胺的一种有效方法。本文以糠醛为原料、氨水为氨源,使用商业Raney Ni催化糠醛还原胺化合成糠胺,考察了氢压、温度、n(糠醛)/n(氨水)、溶剂、催化剂用量等条件对反应的影响。实验结果表明：在1,4-二氧六环溶剂中,0.03 g Raney Ni、n(糠醛)/n(氨水)=1/2、130 ℃、2.0 MPa H₂条件下反应3 h,糠醛转化率100%,糠胺选择性96.3%。与传统方法相比,该工艺实现了非贵金属催化剂作用下高选择性反应,具有操作简单、低成本、收率高等优点。      

Ni(OH)2修饰的三聚氰胺泡沫用于可压缩超级电容器电极

通过化学镀和电化学镀的方法制备了一种Ni(OH)₂电化学活性材料修饰三聚氰胺泡沫(MF)可压缩骨架的超级电容器电极材料MF/Ni(OH)₂。MF/Ni(OH)₂可压缩电极材料表现出最佳的电容性能,例如循环稳定性(即使在40 mA/cm^-3的电流密度下经过2000次充放电循环后,可压缩电极仍能保持90.63%的初始电容)和可压缩稳定性(即使在压缩率为50%时,仍具有97.88%的电容保持率)。层状可压缩超级电容器由MF/Ni(OH)₂弹性材料作为阳极,镍/碳(Ni/C)为阴极以及实验室中常用的滤纸作隔膜材料组成。这种超级电容器装置在不同的压缩下表现出良好的电化学性能和优异的压缩稳定性。最后,使用可压缩的超级电容器来点亮LED灯,以展示其在柔性电子设备中的应用。这些优化的电化学和机械性能表明MF/Ni(OH)₂可作为可压缩超级电容器的应用中的候选电极。     

Robust nickel silicate catalysts with high Ni loading for CO2 methanation

CO₂ is the main component of greenhouse gases and also an important carbon source. The hydrogenation of CO₂ to methane using Ni-based catalysts can not only alleviate CO₂ emissions but also obtain useful fuels. However, Ni-based catalysts face one major problem of the sintering of Ni nanoparticles in the process of CO₂ methanation. Thus, this work has synthesized a series of efficient and robust nickel silicate catalysts (NiPS−X) with different nickel content derived from nickel phyllosilicate by the hydrothermal method. It was found that the Ni loading plays a critical role in the structure and catalytic performance of the NiPS−X catalysts. The catalytic performance gradually increases with the increase of Ni loading. In particular, the highly dispersed NiPS-1.6 catalyst with a high Ni loading of 34.3 wt% could obtain the CO₂ conversion greater than 80%, and the methane selectivity was close to 100% for 48 h at 330 °C and the GHSV of 40,000 mL g⁻¹ h⁻¹. The excellent catalytic property can be assigned to the high dispersion of Ni nanoparticles and the strong interaction between the active component and the carrier, which is derived from a unique layered silicate structure with lots of nickel phyllosilicate and a large number of Lewis acid sites.     

Grain size effects on microstructural stability and creep behaviour of nanotwinned Ni free-standing foils at room temperature

Creep tests were performed on the high stacking fault energy (SFE) nanotwinned (NT) Ni free-standing foils with nearly the same twin thickness at room temperature (RT) to investigate the effects of grain size and loading rate on their microstructural stability and creep behaviour. The grain growth mediated by the twinning/detwinning mechanism at low applied stresses (<800 MPa) and grain refinement via the detwinning mechanism at high applied stresses (>800 MPa) were uncovered in the present NT-Ni foils during RT creep, both of which are attributed to the interactions between dislocations and boundaries. It appears that a higher initial dislocation density leads to a faster primary creep strain rate and a slower steady-state creep strain rate. Unlike the non-twinned metals in which grain growth often enhances the creep strain rate, the twinning/detwinning-mediated grain growth process unexpectedly lowers the steady-state creep strain rate, whereas the detwinning-mediated grain refinement process accelerates the creep strain rate in the studied NT-Ni foils. A modified phase-mixture model combined with Arrhenius laws is put forward to predict the scaling behaviour between the creep strain rate and the applied stress, which also predicts the transition from grain growth-reduced to grain refinement-enhanced steady-state creep strain rate at a critical applied stress. Our findings not only provide deeper insights into the grain size effect on the mechanical behaviour of nanostructured metals with high SFE, but also benefit the microstructure sensitive design of NT metallic materials.     

珊瑚状Ni2P修饰新型四足状Cd0.9Zn0.1SZB/WZ同质结光催化剂的高效可见光光催化产氢

随着社会发展,传统化石能源消耗加剧,人类迫切需要开发新型的清洁能源.半导体光催化分解水产氢是一种非常具有潜力解决能源危机的清洁技术.目前,金属硫化物半导体有着合适的能带结构和高效的光催化产氢能力而得到了广泛的研究.通常,为了提高光催化剂产氢性能,添加贵金属助催化剂是一个行之有效的方法.但是贵金属昂贵的价格限制了其大规模的应用,因此有必要研究储量丰富,价格低廉的高效助催化剂.Ni₂P,CoP,Co₂P,MoP,Cu₃P等过渡金属磷化物具有价格低廉,优异的稳定性和催化性能而被用作电催化产氢的催化剂.通常,用于电催化产氢的催化剂往往可以作为光催化产氢的助催化剂.众所周知,催化性能与材料的形貌密切相关,因此,具有棒状、中空、片状等形貌的金属硫化物被制备并用于光催化产氢.然而,四足状结构的金属硫化物研究较少.在已有的Ni₂P(NP)相关研究中,仅合成了纳米颗粒状的NP.本文成功合成了四足状Cd_0.9Zn_0.1S(CZS)和珊瑚状形貌的NP,进一步得到一系列Ni₂P-Cd_0.9Zn_0.1S(NPCZS)光催化剂,采用XRD,SEM,TEM,XPS和ICP-AES测试了样品的结构、形貌、表面成分和元素含量,并测试了样品的光催化产氢性能.采用水热法合成的CZS样品具有特殊的四足状形貌,足部由纳米棒组成.XRD结果表明,四足状CZS中立方相(WZ)和六方相(ZB)共存.经TEM进一步分析,发现CZS中心部位呈ZB相结构,而足部却是WZ相.经光催化性能测试,这种新型四足状CZS表现出优异的光催化产氢性能.进一步通过超声或研磨破坏四足状结构后,发现CZS的产氢性能显著下降,说明四足状形貌是材料性能提高的关键.通过分析WZ和ZB两物相的价带顶和导带底的电位发现,ZB/WZ间形成的同质结可以加速光生载流子的分离和传输.NP也采用水热法制备,其具有珊瑚状形貌.该形貌具有高的比表面积,可以提供更多的活性位点,进一步提高了材料的光催化性能.光催化性能测试表明,NP负载量为12 wt%的NPCZS-12样品表现出很好的产氢性能(l.88 mmol h^-1),是纯CZS的1.43倍.同时,NPCZS-12具有良好的光稳定性和循环使用性能.结合光催化实验、光谱实验、表面光电压和电化学测试的结果发现,四足状形貌、同质结和NP助催化剂的协同效应是NPCZS具有良好光催化性能的主要原因.