显像管调制特性的测量与分析

测试了显象管调制特性曲线，并分析了特性曲线与显像管工作原理．     

三组元乳化液雾化特性的研究

采用Malvern粒度仪对柴油、甲醇和水三组元乳化液的雾化特性进行了研究。实验发现:对于压力雾化喷嘴来说,本文所涉及的乳化液由于粘度高于纯柴油,因此雾化效果比纯柴油差,而且喷射压力、乳化剂的粘度和乳化液的组份对乳化液的雾化特性具有显著的影响。随着喷射压力的升高,乳化液喷雾粒径将随之减小;若乳化液中柴油的含量(柴油不少于50％)降低,乳化液的雾化粒径将随之增加;若采用高粘度的乳化剂,相应乳化液喷雾的粒径也大。     

X波段五腔渡越管振荡器的理论与实验研究

 提出了一种新结构的X波段五腔渡越管振荡器，进行了理论和实验研究。根据场分布进行了一维非线性分析，结果表明该结构可以产生高功率微波，并判断了工作模式，为TM₀₁模的3π/5模。采用粒子模拟验证了一维非线性分析的结论，并优化设计出五腔渡越管振荡器,优化结果为：输出功率约1 GW， 工作频率9.3 GHz，束波转换效率约22%。实验中，通过参数调节，得到频率约9.25 GHz，峰值功率约780 MW，脉宽（半高宽）21 ns的输出微波，束波转换效率约为16%。实验结果与模拟结果基本符合。     

Space–time integrated least squares: a time‐marching approach

A time‐marching formulation is derived from the space–time integrated least squares (STILS) method for solving a pure hyperbolic convection equation and is numerically compared to various known methods. Copyright © 2004 John Wiley & Sons, Ltd.     

On the tribological characteristics of dynamically loaded journal bearing with micropolar fluids

The addition of the additives to the lubricant oil to enhance the characteristics of the lubricant will influence the performance of the bearings. Based on the theory of micropolar fluids, the tribological characteristics of a dynamically-loaded journal bearing are numerically studied. Comparisons are made between the Newtonian fluids and the micropolar fluids. It is shown that for a dynamically-loaded journal bearing, the micropolar fluids yield an increase not only in the friction force, but also in the friction coefficient. In addition, the oil film pressure and the oil film thickness are obviously higher than that of Newtonian fluids.     

受迫振动演示实验装置

本文叙述用示波器显示来演示受迫振动的实验装置，可直观地向学生展示受迫振动的幅频特性和相频特性。     

光敏电阻基本特性测量实验的设计

介绍了测量CdS光敏电阻的伏安特性和光照特性的实验方法，并给出了相应的实验结果。     

非晶态硒化镉薄膜瞬态光电特性

本文报道用真空热蒸发法淀积的非晶态硒化镉薄膜作光敏介质制备超快光电导探测器。用对撞脉冲锁模Nd:YAG激光器产生的超短光脉冲序列对探测器的响应时间进行检测,结果表明a-CdSe薄膜对皮秒(10^-12秒)级的超短光脉冲作用具有良好的瞬态响应光电特性,探讨a-CdSe薄膜快速弛豫过程的内在机理。     

某类一阶非线性双曲型方程的Cauchy问题

本文考虑一类具实际物理背景的一阶非线性双曲型方程，证明了解的存在唯一及正则性。     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.