催化剂薄层内甲烷水蒸气重整反应强化管内对流换热的数值模拟

本文以竖直圆管内壁催化剂薄层内发生甲烷水蒸气重整反应强化对流换热作为研究对象,对其进行了数值模拟．结果发现,催化剂薄层内的吸热化学反应可以有效地强化对流换热,降低流体和壁面温度,从而对壁面起到保护作用;极限热流密度的大小与流体的入口温度有关,存在最佳入口温度使极限热流密度最大．     

两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

相变光盘介电薄膜ZnS-SiO2 的微结构和光学特性

采用射频磁控溅射法制备了ZnS-SiO₂ 介电薄膜,利用透射电镜和椭偏仪研究了溅射条件对ZnS-SiO₂薄膜微结构和折射率n的影响.研究表明,ZnS-SiO₂薄膜中存在微小晶粒,大小为2～10 nm的ZnS颗粒分布在SiO₂基体中,当溅射功率和溅射气压变化时,ZnS-SiO₂薄膜的微结构和折射率n发生显著变化,微结构的变化是导致折射率n变化的主要原因,通过优化溅射条件可以制备适用于相变光盘的高质量ZnS-SiO₂介电薄膜.     

Experimental investigation of time-dependent cavitation in an oscillatory squeeze film

The occurrence of time-dependent cavitation and tensile stress in an oscillatory oil squeeze film were investigated experimentally. The test apparatus was a simple thrust bearing consisting of two parallel circular plates separated by a thin viscous oil film. During the test, one plate was at rest while the other (transparent) oscillated in a direction normal to its surface. This test configuration was chosen to avoid the rotational motion and complicated geometry of a squeeze film journal bearing. The frequency of oscillation was in the range of 5 to 50 Hz and was controlled by an electro-magnetic exciter. The process of cavity formation and its subsequent development was recorded by a high-speed video camera. Concomitant pressure in the oil film was measured both within and without the cavitation region. It was found that both tensile stress and cavities existed in a squeeze film under certain working conditions.     

Thermal analysis of glasses for proecological applications

Thermal behaviour and biochemical activity of potassium-silicate-phosphate glasses modified by addition of Ca, Mg, acting as ecological fertilisers of controlled release rate of the nutrients for plants were studied. It has been found that the biochemical activity of silicate-phosphate glasses depends on the nature and the number of components forming the glassy framework and is related to the thermal stability of glass demonstrated by the formation of new compounds during the process of crystallisation. It is proved that these seemingly different properties are determined by the same parameters which are the strengths bonds of glass network-formers and modifiers as well as their chemical affinity. This revised version was published online in July 2006 with corrections to the Cover Date.     

蓝宝石R面上ZnO薄膜的NH3掺杂研究

以NH₃为掺杂源,利用金属有机化学气相沉积(MOCVD)系统在蓝宝石R面上生长出掺氮ZnO薄膜。通过XRD,SEM测量优化了其生长参数,在610℃和在80sccm的NH₃流量下生长出了〈1120〉单一取向的ZnO薄膜。经Hall电阻率测量,得知该薄膜呈现弱p型或高电阻率,并对其光电子能谱进行了研究。     

Synthesis and refractive‐index control of fluoropolymers by the polyaddition of bis(epoxide)s and triazine di(aryl ether)s

The polyaddition of fluorine‐containing bis(epoxide)s and fluorine‐containing triazine di(aryl ether)s were examined to give the corresponding fluorine‐containing poly(cyanurate)s. It was observed that the synthesized fluoropolymers had good thermal stabilities and good film‐forming properties. The glass transition temperatures (T_g's) and refractive‐indices (n_D's) of synthesized polymers were determined by differential scanning calorimetry and ellipsometry, respectively, and it was found that the values of T_g's and n_D's were supported by their fluorine containing ratios and skeletons. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4421–4429, 2007     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.     

高能、超短脉冲、可调谐激光器用掺镱氟磷酸盐玻璃研究进展

Yb^3 与其它稀土离子相比有最简单的能级结构，这使它具有一些独特的性质，如避免激发态吸收，消除上转换和浓度猝灭等，因此它是高能输出激光器介质的理想掺杂离子。氟磷玻璃综合了氟化物玻璃和磷酸盐玻璃的优点，可降低磷酸盐的声子能量，改善其易吸湿性；提高氟化物玻璃的物理化学性能等，这使它成为稀土掺杂可调谐光纤激光器的很好的掺杂介质。众多研究表明，Yb^3 掺杂氟磷玻璃是一种很有前途的激光工作物质。本文总结了Yb^3 掺杂氟磷玻璃的特点，性质，结构及存在的问题。     

Thermoplastic poly(ester‐imide)s derived from anhydride‐terminated polyester prepolymer and diisocyanate

The phase‐separation behavior of thermoplastic poly(ester‐imide) [P(E‐I)] multiblock copolymers, (A‐B)_n, was investigated by a stepwise variation of the imide content. All the multiblock copolymers were synthesized by solution polycondensation with dimethylformamide as a solvent. P(E‐I)s were prepared with anhydride‐terminated polyester prepolymer and diisocyanates. Polyester prepolymers were prepared by the reaction of pyromellitic dianhydride and two different polyols [poly(tetramethylene oxide glycol) (PTMG) and polycaprolactone diol (PCL)]. Structural determination was done with Fourier transform infrared spectroscopy and Fourier transform NMR, and the molecular weight was determined by gel permeation chromatography. The effect of the imide content on the thermal properties of the synthesized P(E‐I)s was investigated by thermogravimetric analysis and differential scanning calorimetry. The polymers were also characterized for static and dynamic mechanical properties. Thermal analysis data indicated that the polymers based on PTMG were stable up to 330 °C in nitrogen atmosphere and exhibited phase‐separated morphology. Polymers based on PCL showed multistage decomposition, and the films derived from them were too fragile to be characterized for static and dynamic mechanical properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 341–350, 2004