一种漂移室定位子性能反常现象的研究

研究了一种漂移室定位子性能的反常现象,它关系到定位子的使用寿命．着重测量了暗电流和随机噪声与时间、高压及温度的关系.     

高压下聚苯胺的结构和电性能研究

 以金刚石压腔高压装置为工具，用Ⅱ型金刚石作压砧兼红外窗口，对本征态聚苯胺进行了高压（0~8.4 GPa）就位红外光谱测试。结果表明：在4.8~5.2 GPa压力区间，代表醌环振动的吸收峰相对代表苯环振动的吸收峰变小，表明聚苯胺在此压力区间结构上发生了显著变化，且这种变化是不可逆的。聚苯胺的高压（0~14.5 GPa）电阻测量结果表明：当压力小于7.5 GPa时，电阻随压力升高而显著降低，据此认为聚苯胺为电子性导电物质；在7.5 GPa处电阻出现极小值，然后又缓慢升高，至10 GPa后基本不变。推测聚苯胺电阻极小值是由结构变化引起的。至于红外光谱与电阻测量结果反映聚苯胺结构变化的压力值不一致，可能是由于测试条件不同所致。     

高功率飞秒脉冲激光器的进展

概述了超短激光脉冲技术发展的历程。详尽的论述了啁啾脉冲放大技术的原理和一些关键技术 ,并对当今飞秒激光器研究发展的状况进行了综述。在分析其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。结果表明 ,脉冲激光放大系统以后的发展方向是 :更短脉冲 ;追求更高峰值功率 ;连续光谱调谐化 ;向小型化乃至全光纤化发展。     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

介质的非均匀性对高次谐波影响的研究

讨论了气体介质的非均匀性对飞秒激光高次谐波产生过程的可能影响.计算结果表明,采用喷阀技术所提供的气体介质的密度梯度和气体原子运动速度的影响很小,不会产生实验上可观测的效果.这一结果支持了喷气靶在高次谐波产生中的广泛应用 关键词： 高次谐波 气体介质 各向异性 飞秒激光     

The Properties of Light Pressure Force with High Order in Laser Fields

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓ,ｂｏｔｈｔｈｅｔｈｅｏｒｅｔｉｃａｌａｎｄｅｘｐｅｒｉｍｅｎｔａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｏｎｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｈａｖｅｂｅｃｏｍｅｏｎｅｏｆｔｈｅｍａｊｏｒｆｉｅｌｄｓｉｎａｔｏｍｉｃ,ｍｏｌｅｃｕｌａｒａｎｄｏｐｔｉｃａｌ ｐｈｙｓｉｃｓ[1～ 8] .Ｔｈｅｄｅｖｅｌｏｐｍｅｎｔｏｆｌａｓｅｒｃｏｏｌｉｎｇａｎｄｔｒａｐｐｉｎｇｔｅｃｈｎｏｌｏｇｙｉｓｉｍｐｏｒｔａｎｔｆｏｒｔｈｅａｐｐｌｉｃａｔｉｏｎｓｓｕ…     

狭缝式高速摄影机胶片的计算机判读

根据狭缝摄影机胶片的成象原理,运用数字图象处理技术,对狭缝式高速摄影机胶片判读工作的计算机化进行研究.应用结果表明,该技术先进实用,极大地提高了判读的精度和效率,将是这种胶片判读技术的发展方向.     

Experimental identification of physical parameters of fluid-filled pipes using acoustical signal processing

A method is formulated for the identification of an unknown physical parameter of a fluid-filled pipe using the measurement of sound speed in the pipe. The method uses a simple formula which provides the relationship between the sound speed and a few physical parameters of the pipe: thickness, diameter, wall material constants and fluid constants. Once the sound speed in the pipe is measured, the simple formula can be used to extract one of the unknown parameters providing the remaining ones are known.The sound speed in the pipe is measured using a 3-transducer array. In order to demonstrate the potential of the technique the results of several measurements obtained in a water-filled steel pipe are presented.The required accuracy of the measurement of sound speed and of the specification of known parameters is analysed. The accuracy depends on the unknown parameter which is to be identified. For example, if the pipe thickness is the unknown parameter, the other parameters have to be known within a very narrow margin of error. On the contrary, if the fluid properties have to be identified the needed accuracy of known parameters gets much lower.     

高功率微波高斯馈源口面场分析

 用波导本征模展开方法对用于高功率微波发射系统的方角锥高斯馈源口面场进行分析，提出结合馈源远场辐射特性和避免高功率击穿折衷选定相应的高斯模注腰半径，进而确定多个波导模幅值，从而为运用模匹配或耦合波理论设计高斯馈源提供依据。