(NH4)2MoS4在活性炭上浸渍过程的研究:Ⅱ.干燥机理及模型

（ＮＨ＿４）＿２ＭｏＳ＿４在活性炭上浸渍过程的研究Ⅱ．干燥机理及模型秦慧芳，张成芳，陆岗，俞丰，朱子彬（华东理工大学无机化工研究所，上海２００２３７）２３７）关键词硫代钼酸铵，活性炭，干燥，钼分布，干燥模型负载型催化剂的活性组分在载体上的分布，受浸渍...     

K2O-ZnO-Al2O3-B2O3-SiO2系掺Cr3+透明莫来石微晶玻璃的研究

采用了X射线衍射、透射电镜和吸收光谱及荧光光谱技术研究了K2O－ZnO-Al2O3-B2O3－SiO2系掺Cr^3 玻璃的析晶性能和光谱。研究结果表明：在K2O－Al2O3-B2O3-SiO2系掺Cr^3 玻璃的基础上引入ZnO后，析晶性能明显改善；析晶温度降低，析出的纳米莫来石微晶均匀、规则；微晶玻璃的发光强度明显增强。     

Evolution of stress and strain relaxation of Ge and SiGe alloy films on Si(0 0 1)

The growth of Ge and SiGe alloy films on Si substrates has attracted considerable interest in the last years because of their importance for optoelectronic devices as well as Si-based high speed transistors. Here we give a short overview on our recent real time stress measurements of Ge and SiGe alloy films on Si(0 0 1) performed with a sensitive cantilever beam technique and accompanied by structural investigations with atomic force microscopy. Characteristic features in the stress curves provide detailed insight into the development and relief of the misfit strain. For the Stranski–Krastanow system Ge/Si(0 0 1) as well as for SiGe films with Si contents below 20%, the strain relaxation proceeds mainly into two steps: (i) by the formation of 3D islands on top of the Ge wetting layer; (ii) via misfit dislocations in larger 3D islands and upon their percolation.     

受激喇曼散射在掺铒光纤放大器中的影响

本文在分析了均匀掺杂分布式光纤放大器（d－EDFA）的基础上，提出了沿传输方向掺杂浓度单调下降（单变），和降升结合（两变）的两种渐变型分布式光纤放大器，并用传输方程研究了透明传输和最佳掺杂浓度下，受激喇曼散射对均匀、单变和两变型三种d－EDFA的各种特性的影响．     

孤子掺杂光纤放大的半径典模型与分析

建立了孤子掺杂光纤放大的半经典模型，给出了分布放大透明传输的泵浦条件，详细讨论了激发态吸收的影响．文中结果为Ｅｒ￣３＋掺杂光纤孤子放大器的设计提供了重要理论依据．     

Synthesis and copolymerization of new phosphorus‐containing acrylates

Two phosphorus‐containing acrylate monomers were synthesized from the reaction of ethyl α‐chloromethyl acrylate and t‐butyl α‐bromomethyl acrylate with triethyl phosphite. The selective hydrolysis of the ethyl ester monomer with trimethylsilyl bromide (TMSBr) gave a phosphonic acid monomer. The attempted bulk polymerizations of the monomers at 57–60 °C with 2,2′‐azobisisobutyronitrile (AIBN) were unsuccessful; however, the monomers were copolymerized with methyl methacrylate (MMA) in bulk at 60 °C with AIBN. The resulting copolymers produced chars on burning, showing potential as flame‐retardant materials. Additionally, α‐(chloromethyl)acryloyl chloride (CMAC) was reacted with diethyl (hydroxymethyl)phosphonate to obtain a new monomer with identical ester and ether moieties. This monomer was hydrolyzed with TMSBr, homopolymerized, and copolymerized with MMA. The thermal stabilities of the copolymers increased with increasing amounts of the phosphonate monomer in the copolymers. A new route to highly reactive phosphorus‐containing acrylate monomers was developed. A new derivative of CMAC with mixed ester and ether groups was synthesized by substitution, first with diethyl (hydroxymethyl)phosphonate and then with sodium acetate. This monomer showed the highest reactivity and gave a crosslinked polymer. The incorporation of an ester group increased the rate of polymerization. The relative reactivities of the synthesized monomers in photopolymerizations were determined and compared with those of the other phosphorous‐containing acrylate monomers. Changing the monomer structure allowed control of the polymerization reactivity so that new phosphorus‐containing polymers with desirable properties could be obtained. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2207–2217, 2003     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Photocatalytic Synthesis of Oxygenates from Gaseous CO2 and CH4 over Semiconductor

Photoinduced synthesis of CO2 and CH4 was investigated using a batch reaction system on several photoactive materials supported on silicon dioxide. Single semiconductor showed higher selectivity to C1 compounds. The production of C2-C3 oxygenates took place preferentially on composite semiconductor photocatalysts. In particular, it was found that acetone was the primary product over Cu/CdS-TiO2/SiO2.     

High responsivity, LWIR dots-in-a-well quantum dot infrared photodetectors

In this paper we report studies on normal incidence, InAs/In_0.15Ga_0.85As quantum dot infrared photodetectors (QDIPs) in the dots-in-a-well (DWELL) configuration. Three QDIP structures with similar dot and well dimensions were grown and devices were fabricated from each wafer. Of the three devices studied, the first served as the control, the second was grown with an additional 400 Å AlGaAs blocking layer, and the third was grown on a GaAs n+ substrate with the intention of testing a single pass geometry. Spectral measurements on all three devices show one main peak in the long-wave IR (≈8 μm). The absorption was attributed to the bound-to-bound transition between the ground state of the InAs quantum dot and the ground state of the In_0.15Ga_0.85As well. Calibrated peak responsivity and peak detectivity measurements were performed on each device at 40, 60, and 80 K. For the same temperatures, frequency response measurements from 20 Hz to 4 kHz at a bias of V_b=−1 V were also performed. The addition of the blocking layer was shown to slightly enhance responsivity, which peaked at 2.4 A/W at 77 K, V_b=−1 V and responsivity was observed to be significantly reduced in the single pass (n+ substrate) sample. The rolloff of the frequency response was observed to be heavily dependent on temperature, bias, and irradiance. The results from the characterization of each sample are reported and discussed.