(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

激光除冰研究

架空输送电线路因覆冰而导致的事故危害性很大,本文总结了目前国内外输电线路导线覆冰的现状。统计国内外探索出来的各种预防,融化,除冰等很多解决方案。通过研究和探讨,分析导线覆冰的传热和能量,运用了多种激光器进行激光熔(除)冰实验,比较研究二氧化碳激光器的除冰情况。以及提出激光熔冰的方法、研究方向和前景。     

The Calibrating Theory in the Network Parameters Measurement of Microwave and MMW Devices

The paper introduces a special system calibration technology in s-parameters measurement of microwave and millimeter wave devices. The 8-term errors module is built by analyzing the signals flowing in the measurement system. Then the calibration technology using non-standard kits is designed on the base. Finally, the experiment using the calibration technology is introduced.     

可重构制造系统重组过程中设备选择模型的研究

根据生产任务选择加工设备进行制造资源重组是实现可重构制造系统的关键问题之一，由于设备的选择涉及到多种因素，既有定量指标，又有定性指标，传统的依靠人工经验的方法显得力不从心。本文首先结合实际情况，提出了一套设备选择评价体系，通过对模糊判断矩阵采用最小对数二乘法确定各评价因素的权重系数，针对定性指标和定量指标采用不同的方法确定其性能指标值，通过模糊积分对评判指标进行综合评判，最后进行了实例研究。所提出的方法有效地简化了决策过程，为可重构制造系统设备选择提供了一套行之有效的方法。     

Challenging Students to View the Concept of Area in Triangles in a Broad Context: Exploiting the Features of Cabri-II

This study focuses on the constructions in terms of area and perimeter in equivalent triangles developed by students aged 12–15 years-old, using the tools provided by Cabri-Geometry II [Labore (1990). Cabri-Geometry (software), Université de Grenoble]. Twenty-five students participated in a learning experiment where they were asked to construct: (a) pairs of equivalent triangles “in as many ways as possible” and to study their area and their perimeter using any of the tools provided and (b) “any possible sequence of modifications of an original triangle into other equivalent ones”. As regards the concept of area and in contrast to a paper and pencil environment, Cabri provided students with different and potential opportunities in terms of: (a) means of construction, (b) control, (c) variety of representations and (d) linking representations, by exploiting its capability for continuous modifications. By exploiting these opportunities in the context of the given open tasks, students were helped by the tools provided to develop a broader view of the concept of area than the typical view they would construct in a typical paper and pencil environment.     

HgCl2/I2复合催化剂协同催化合成异丙醇钇的研究

以金属钇和异丙醇为原料，以HgCl2/I2为复合催化剂，通过对金属钇的机械加工以增加其比表面，并将异丙醇脱水使其含水量降低至0．05％，体系在82℃回流5h，经过滤、减压蒸馏，得到了白色海绵状异丙醇钇，其产率高达83％，合成时间比文献报道的缩短了19h，产率提高了8％。文章确定了催化剂的最佳用量为20gY加入60mg HgCl2/I2，研究了合成产率与HgCl2/I2催化剂和HgCl2催化剂的依赖关系及异丙醇中含水量对合成产率的影响，并对HgCl2/I2的催化作用机理进行了初步探讨。     

蕴涵代数与BCK代数

系统研究 Fuzzy蕴涵代数与 BCK代数之间的关系 ,给出 MV代数与 BCK代数之间的联系 ,建立正则 FI代数和对合 BCK代数的对偶代数     

高频强泵浦场激发的等离子体参量不稳定性的特性

本文论证了当泵浦波的强度足够强时,在相当普遍的条件下,对均匀等离子体,唯一可以发生的参量不稳定性是类似于弱场的振荡二束不稳定性(OTSI)。对均匀及弱不均匀等离子体,高频强泵浦场激发的参量不稳定性都是绝对不稳定性。同样的性质在磁化等离子体中也可以得到。 关键词：     

激光等离子体2660紫外探针及干涉系统

成功地在六路高功率Nd玻璃激光装置上建立了2660紫外激光探针和适合紫外波段的Normaski干涉仪,首次将可见波长的连续激光应用于紫外干涉仪中靶成像调整和光路准直。利用该紫外光干涉仪,在铜柱状靶(φ500μm)上测量了厚等离子体中高达0.6n。的电子密度。     

Error analysis: a tool for selecting travel demand models

In developing travel demand models it is generally assumed that the base-year data used in developing the parameters, as well as the forecasted data to be used as independent variables for the design year, are of acceptable quality. The purpose of this paper is to present the application of error propagation theory in assesing the predictive quality of one type of travel demand forecasting model (multinomial logit models) and to demonstrate how error considerations can be used as a tool for identifying the optimal model. The general conclusions of this study are that: (1) it is indeed possible to quantify errors in dependent variables in logit models as a consequence of errors in independent variables; and (2) error consideration can be used as a tool for identifying the optimal model from a set of candidate models. Further research is recommended to develop better insights into the phenomenon of error propagation so that the consideration of errors can be a factor in decisions on model selection.