The Effect of the Spacer of Bis(biurea) Ligands on the Structure of A2L3‐type (A=anion) Phosphate Complexes

By tuning the length and rigidity of the spacer of bis(biurea) ligands L, three structural motifs of the A₂L₃ complexes (A represents anion, here orthophosphate PO₄^3?), namely helicate, mesocate, and mono‐bridged motif, have been assembled by coordination of the ligand to phosphate anion. Crystal structure analysis indicated that in the three complexes, each of the phosphate ions is coordinated by twelve hydrogen bonds from six surrounding urea groups. The anion coordination properties in solution have also been studied. The results further demonstrate the coordination behavior of phosphate ion, which shows strong tendency for coordination saturation and geometrical preference, thus allowing for the assembly of novel anion coordination‐based structures as in transition‐metal complexes.     

Characteristics investigation on heat transfer growth of sonochemically synthesized ZnO-DW based nanofluids inside square heat exchanger

Journal of Thermal Analysis and Calorimetry - In recent decades, the growth of heat transfer using nanomaterials in the conventional base fluid has caught the attention of researchers...     

Hybrid (ND-Co3O4/EG) nanoliquid through a permeable cylinder under homogeneous-heterogeneous reactions and slip effects

Journal of Thermal Analysis and Calorimetry - Modeling and computations are performed to study the ND-Co3O4/EG hybrid nanoliquid mixed convective flow past a vertical porous cylinder. The flow...     

离子对反相高效液相色谱法同时测定尿液中复方α-酮酸片的5种有效成分

建立了同时测定尿液中复方α-酮酸片5种有效成分(消旋羟蛋氨酸钙(HMACa)、酮缬氨酸钙(KVCa)、消旋酮异亮氨酸钙(KILCa)、酮亮氨酸钙(KLCa)和酮苯丙氨酸钙(KPACa))的离子对反相高效液相色谱法。分别考察了离子对试剂浓度、缓冲盐浓度和流动相pH值等参数对分离情况的影响。最终采用Waters Symmetry C18色谱柱(250 mm×4.6 mm,5μm);以乙腈和含15 mmol/L四丁基氢氧化铵的20 mmol/L磷酸盐缓冲液(pH 7.0)为流动相进行梯度洗脱,流速为1.0 mL/min;柱温为35℃;检测波长为210 nm。在上述条件下,5种有效成分得到很好的分离,并且不受尿液中内源性基质的干扰,在20~200 mg/L范围内线性关系良好(r≥0.999 0);HMACa、KVCa、KILCa、KLCa和KPACa的检出限(S/N=3)分别为3.0、5.0、3.6、5.7和2.5 mg/L;定量限(S/N=10)分别为9.6、16.7、12.0、19.0和8.3 mg/L;日间、日内精密度均小于7%;平均回收率在86.79%~112.00%之间,RSD小于9%(n=5)。该方法准确,灵敏度高,重现性好,适用于尿液中这5种有效成分的检测。     

Anisotropic Elastic-Viscoplastic Properties at Finite Strains of Injection-Moulded Low-Density Polyethylene

Injection-moulding is one of the most common manufacturing processes used for polymers. In many applications, the mechanical properties of the product is of great importance. Injection-moulding of thin-walled polymer products tends to leave the polymer structure in a state where the mechanical properties are anisotropic, due to alignment of polymer chains along the melt flow direction. The anisotropic elastic-viscoplastic properties of low-density polyethylene, that has undergone an injection-moulding process, are therefore examined in the present work. Test specimens were punched out from injection-moulded plates and tested in uniaxial tension. Three in-plane material directions were investigated. Because of the small thickness of the plates, only the in-plane properties could be determined. Tensile tests with both monotonic and cyclic loading were performed, and the local strains on the surface of the test specimens were measured using image analysis. True stress vs. true strain diagrams were constructed, and the material response was evaluated using an elastic-viscoplasticity law. The components of the anisotropic compliance matrix were determined together with the direction-specific plastic hardening parameters.