用于丁烷选择氧化制顺酐的铈锆复合钒磷氧催化剂的研究

 在钒磷氧（VPO）催化剂中添加适量铈锆复合氧化物，得到了一\r\n种新型的铈锆复合钒磷氧催化剂．该催化剂对丁烷选择性氧化制顺酐反\r\n应的催化性能比纯VPO催化剂有了显著提高．在丁烷／空气共进料反应\r\n条件下，其顺酐收率比纯VPO催化剂提高了一倍；在无氧反应条件下，\r\n其可参与选择性氧化制顺酐的晶格氧量为纯VPO催化剂的2．2倍．BET比\r\n表面积测试、X射线衍射、钒平均价态测定和程序升温实验等表征结果\r\n表明，混合在催化剂活性相中的少量铈锆复合氧化物参与了VPO体系的\r\n氧化还原过程，并起到了以下两方面的作用：（1）促进了（VO）2P2O\r\n7相的形成，稳定了钒的平均价态，有利于最终形成晶相结构良好和反\r\n应性能稳定的VPO催化剂；（2）显著提高了VPO催化剂的氧化还原性能\r\n，大大增加了催化剂的可逆储氧量．     

分子筛负载钒配合物催化剂对烃类氧化的择形选择性研究

研究了四价钒配合物VO(pic)2·H2O及其分子筛负载型催化剂VO(pic)2-NaY对芳香烃和正构烷烃的催化氧化性能.实验结果证明,VO(pic)2-NaY催化剂具有与VO(pic)2·H2O配合物催化剂相似的催化氧化活性,而且使对位产物(芳香烃为底物)和伯醇(底物为正构烷烃)的选择性得到提高,显示出均相配合物催化剂所不具有的择形选择性.     

铁络合物/八面沸石催化剂中沸石主体的纳米效应

 采用自由配体法制备了Fephen／nano－X和Fephen／nano－Y两种\r\n不同粒度的Fephen／八面沸石纳米复合材料（简称为Fephen／FAU），\r\n并采用X射线衍射、傅里叶变换红外光谱、漫反射紫外－可见光谱、热\r\n重－差热分析和催化反应等手段对其进行了表征．研究结果发现，采用\r\n纳米沸石作主体是自由配体法制备金属络合物／分子筛复合材料中提高\r\n络合物负载量的有效方法．催化反应结果表明，与普通粒度的Fephen／\r\nY复合材料相比，两种不同粒度的Fephen／nano－X和Fephen／nano－Y\r\n纳米复合材料对环己烷氧化反应的催化活性有很大的提高．由于两种纳\r\n米沸石主体的差异，两种纳米复合材料的催化性能也明显不同，不仅对\r\n环己烷的转化能力不同，对氧化产物的选择性也不同．     

不同环大小分子筛对钼基分子筛催化剂上甲烷无氧芳构化反应的影响

 钼基分子筛催化剂，由于不同分子筛的孔道大小及孔道形状不同\r\n，对甲烷芳构化反应表现出不同的催化性能．具有8元环孔道结构的小\r\n孔ERS－7分子筛没有催化活性，说明甲烷的芳构化反应离不开分子筛孔\r\n道的择形作用，较小的孔道中不能生成苯等芳烃．具有10元环孔道结构\r\n的ZSM－5，ZSM－11和ZRP－1三种分子筛具有较好的催化性能，但由于\r\n其孔道大小及孔道形状的差别在催化行为上表现出一定的差异．具有1\r\n0元环和12元环孔道结构的MCM－22分子筛，尤其对苯等轻芳烃而言，催\r\n化性能最佳．具有12元环孔道结构的JQX－1以及中孔分子筛SBA－15，\r\n虽然具有一定的催化性能，但活性较低．研究结果表明，孔道大小与苯\r\n分子动态直径相近或孔道稍大的分子筛是催化甲烷芳构化反应的良好载\r\n体，孔道过大或过小都不利于苯和萘等芳烃的生成．     

中孔分子筛HMS负载钴催化剂在费-托合成中的应用:载体HMS的孔径对钴基催化剂性能的影响

 用不同链长度的十二胺，十四胺，十六胺和十八胺等伯胺为模板\r\n剂合成了具有不同孔径大小的HMS中孔分子筛．XRD和低温氮吸附测定表\r\n明，HMS具有典型的中孔分子筛特征，且其孔径大小随HMS合成中所用模\r\n板剂链长度的增加而增加．以HMS为载体，采用孔体积浸渍法制备了负\r\n载量为7．5％的钴催化剂，在接近工业试验条件下（n（H2）／n（CO）\r\n＝2．1，GHSV＝500h－1，p＝2．0MPa，θ＝227℃）考察了载体孔径大\r\n小对费－托合成反应性能的影响．结果表明，与常规的SiO2载体相比，\r\nHMS负载钴催化剂具有更高的催化活性和C5＋选择性；而且，CO转化率\r\n，C5＋选择性及产物中的蜡油比均随着HMS载体孔径的增大而升高．以\r\n7．5％Co／HMS－18为催化剂，CO转化率为78．0％，C5＋选择性为80．\r\n8％，蜡油比为11．1．     

钛硅分子筛TS-1催化氯丙烯环氧化反应动力学研究

 摘要：研究了钛硅分子筛催化氯丙烯环氧化反应的条件及动力学行为．\r\n结果表明，以钛硅分子筛为催化剂，氯丙烯可被高选择性地氧化为环氧\r\n氯丙烷．环氧化反应速度与分子筛中骨架钛的含量及分子筛的用量呈正\r\n比关系，是一级反应．对于氧化剂H2O2，只有当c（H2O2）＜0．4mol／\r\nL时，环氧化反应为一级反应；而c（H2O2）＞1．0mol／L时，为零级反\r\n应．对于氯丙烯，随着其浓度的变化，环氧化反应的级数在1和0之间．\r\n然而，只有当氯丙烯浓度很高时，环氧化反应的级数才有明显的降低．\r\n根据实验结果和Eley－Rideal单分子吸附方程，提出了氯丙烯环氧化反\r\n应的动力学模型．\r\n关键词：钛硅分子筛，氯丙烯，过氧化氢，环氧化，环氧氯丙烷，反应\r\n动力学     

HY沸石上2,6-二叔丁基萘的择形合成

 研究了脱铝HY沸石（n（Si）／n（Al）＝3．8）上萘（naph）的\r\n选择性叔丁基化反应．结果表明，八面沸石对该反应过程有较好的择形\r\n催化作用，两种异构化产物（2，6－二叔丁基萘和2，7－二叔丁基萘）\r\n之间存在着热力学平衡，即两种异构化产物可在酸性中心位上相互转化\r\n．在以叔丁醇为烷基化试剂，WHSV＝2h－1，n（t－BuOH）／n（naph）\r\n＝3，反应温度为120℃的反应条件下，萘的转化率可达98．43％，β－\r\n位选择性可高达100％，二叔丁基萘收率可达74．34％，2，6－二叔丁\r\n基萘／2，7－二叔丁基萘质量比为6．24．     

硝基苯加氢合成对氨基酚用负载铂催化剂的制备

 用甲醛还原沉积法制备了活性炭负载的铂催化剂（Pt／AC）和不\r\n同载体负载的铂催化剂，并考察了催化剂对硝基苯加氢制备对氨基酚反\r\n应的催化性能．结果表明，还原Pt（Ⅳ）的甲醛用量是影响催化剂性能\r\n的关键因素，甲醛必须过量而且存在一个最佳值．增加催化剂的铂负载\r\n量，不能有效提高加氢反应速度，反而易降低对氨基酚选择性；低铂负\r\n载量催化剂具有较高的活性、选择性及稳定性．XPS和TEM表征结果表明\r\n，金属铂集中分布于活性炭颗粒外部，其颗粒大小介于2～12nm间．炭\r\n载体催化剂的活性和选择性明显高于金属氧化物载体催化剂．掺入适量\r\n的Mg可显著提高Pt／AC催化剂的活性和选择性．     

正丁烷氧化制顺酐流化床催化剂的性能

 考察了前驱体制备过程中水合肼／五氧化二钒摩尔比（以下简记\r\n为n（N2H4）／n（V2O5））对催化剂性能的影响．由较高的n（N2H4）\r\n／n（V2O5）比制得的催化剂，其（VO）2P2O7相含量较多，正丁烷转化\r\n率较高．随着n（N2H4）／n（V2O5）比的减小，δ－VOPO4相的含量逐\r\n渐增多，正丁烷转化率随之升高；而顺酐选择性开始时升高，达到最大\r\n值后逐渐降低．在n（N2H4）／n（V2O5）＝0．34时制备的催化剂最佳\r\n，在丁烷浓度为4．0％、空速为500h－1及反应温度为420℃的反应条件\r\n下，顺酐收率可达49．74％．本文中细粒床催化剂有较大的操作弹性．     

锌含量对Zn/HZSM-5催化剂性能的影响

 研究了不同锌含量的Zn／HZSM－5分子筛的表面酸性及其对正己\r\n烷芳构化反应的催化活性、选择性和稳定性．结果表明,锌组元的引入\r\n减少了HZSM－5表面的B酸,增加了L酸,总酸量增大;正己烷转化率随\r\n锌含量的增加先降低后升高;芳烃产率和芳构化选择性则随锌含量的增\r\n加先增大后趋于平缓;反应过程中催化剂的积炭速度、孔体积和比表面\r\n积下降速度都随着锌含量的增加而加快;锌含量大于1％时,Zn／HZSM\r\n－5的催化稳定性不如HZSM－5,且随着锌含量的增加失活速度加快．优\r\n选的锌含量为1．0％～2．9％．此外,讨论了Zn／HZSM－5的催化性能\r\n与其表面性质的关系．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.