Adsorption of hydrocarbons from solutions and gas phase on silica and alumina modified with silver and gold ions

The paper reports the immobilization of Ag⁺ cations on alumina and silica and AuCl ₄ ^? anions on amino silica and alumina. The method of inverse gas chromatography have demonstrated that Ag(I)-silica is selective for the separation of alkanes, alkenes, alkines, and arenes. The dependence of the capacitance of Ag(I) and Au(III) composites with regard to phenylacetylene (PHA) on the nature of the carriers, surface concentration, and technique of immobilizing ion metals has been considered. The isotherms of the adsorption of PHA from solutions in octane have been measured. It has been revealed that the capacitance of composites with regard to toward PHA prepared by the immobilization of ammoniates of silver nitrate on silicon dioxide is several times higher than for composites based on alumina with the same silver concentration and composites prepared by the immobilization of silver nitrate on silicon dioxide. The capacitance of the Au(III) composite based on alumina for PHA is significantly higher than for that based on aluminum oxide. The highest capacitance for PHA (0.83 and 0.88 molecules per metal ion) is observed for Ag(I) silica and the Au(III) alumina composite. In the visible region, the diffuse reflection spectra of amino silica Au(III) composites have a significant shift of the maximum of adsorption band along with the decrease in the concentration of immobilized anions of AuCl ₄ ^? , which evinces the formation of coordination bonds between free amin?propyl groups of the silica carrier and gold atom. The formation of these bonds prevents the adsorption of PHA on amino silica Au(III) composites with low gold concentrations.     

银纳米颗粒负载阶层多孔二氧化硅块体的制备及表征

以溶胶-凝胶伴随相分离法制备的阶层多孔二氧化硅作为载体,3-氨丙基三乙氧基硅烷（APTES）为改性剂,乙醇为还原剂,在阶层多孔二氧化硅固体骨架上进行银纳米颗粒均匀负载. 利用扫描电镜（SEM）、透射电镜（TEM）、X射线衍射（XRD）、汞压、N₂吸附/脱附、X射线光电子能谱（XPS）等测试技术对银纳米颗粒负载阶层多孔二氧化硅进行了表征,探讨了APTES表面改性、乙醇还原机理以及银纳米颗粒负载块体的孔结构特征变化规律. 结果表明：APTES表面改性将氨基接枝于阶层骨架上,氨基与银离子形成银氨离子,银氨离子经乙醇还原后将平均粒径约16 nm的银纳米颗粒成功负载于二氧化硅的大孔及介孔内部;负载后的阶层多孔块体的大孔骨架未受到破坏,但其比表面积由418 m²·g^-1下降到254 m²·g^-1,两次还原负载能提高银纳米颗粒的负载量.     

银纳米颗粒负载阶层多孔二氧化硅块体的制备及表征

以溶胶-凝胶伴随相分离法制备的阶层多孔二氧化硅作为载体,3-氨丙基三乙氧基硅烷(APTES)为改性剂,乙醇为还原剂,在阶层多孔二氧化硅固体骨架上进行银纳米颗粒均匀负载.利用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、汞压、N2吸附/脱附、X射线光电子能谱(XPS)等测试技术对银纳米颗粒负载阶层多孔二氧化硅进行了表征,探讨了APTES表面改性、乙醇还原机理以及银纳米颗粒负载块体的孔结构特征变化规律.结果表明:APTES表面改性将氨基接枝于阶层骨架上,氨基与银离子形成银氨离子,银氨离子经乙醇还原后将平均粒径约16 nm的银纳米颗粒成功负载于二氧化硅的大孔及介孔内部;负载后的阶层多孔块体的大孔骨架未受到破坏,但其比表面积由418 m2·g-1下降到254m2·g-1,两次还原负载能提高银纳米颗粒的负载量.     

Study on the chemisorption kinetics of Methylene Blue using SERS technique

SERS technique was used to study the chemisorption kinetics of Methylene Blue (MB) on the HNO3-etched silver surface. The adsorption kinetic parameters were deduced from different vibrational modes at a low concentration of 3.5×10-6 mol/L, and it showed that MB adsorbed uniformly (monolayerly) on silver surface. However, the adsorptive behavior turned anomalous at relatively higher concentrations and a possible explanation was suggested. In addition, the influence of Cl- ions on the adsorption states of MB was investigated, and it was shown that MB molecules, adsorbed on the silver surface, tended to transform from the "lying-down" state to the "end- on"4 state after Cl- ions were added.     

氧化铁和羟基氧化铁光催化还原银离子

在波长λ≥320 nm的紫外灯照射下, 水溶液中的银离子能在氧化铁和羟基氧化铁催化剂表面发生还原反应而生成颗粒银. 在这些催化剂上, Ag(I)的等温吸附线都符合Langmuir吸附方程; Ag(I)的初始还原速率均随其初始吸附量的增加而线性增大, 并且增大的幅度依α-Fe2O3>α-FeOOH>γ-Fe2O3>γ-FeOOH>δ-FeOOH的顺序降低. 但是, 在前三种催化剂上, 只有当Ag(I)的吸附量达到其饱和吸附量的一半时, Ag(I)的还原才能发生, 并且几乎不受氮气的影响. 在δ-FeOOH和TiO2体系中通入氮气, 能显著加快Ag(I)的光催化还原. 这说明O2与Ag(I)竞争催化剂上的吸附位点和还原物种, 且与催化剂的性质有关. XRD分析表明, α-Fe2O3和δ-FeOOH分别具有较好和较差的结晶度. 这说明氧化铁和羟基氧化铁的结晶度越高, 越有利于光生载流子的分离及其与表面目标物种发生氧化还原反应.     

Olefin adsorption on silica-supported silver salts--a DFT study

Recent experiments have shown that silver salts supported on mesoporous silicas display excellent adsorption selectivities of ethylene over ethane and propylene over propane. Employing the techniques of density functional theory, we have investigated the fundamental bases of this separation process by examining silver salts dispersed on model silica surfaces. Our model system includes Ag+ cations, their counteranions, silica supports, and surface silanols. Both adsorption geometries and energetics of ethylene and propylene were explored. Our results indicate that the nature of the Ag-olefin interaction is predominantly hybridization between Ag d and olefin pi states, which is supported by analyses of electron density difference plots and density of states. The counteranions, such as NO3- were found to interact strongly with surface silanols through multiple hydrogen bonds but have limited effect on the adsorption energy of olefins on the Ag+ cations. The current work supports recent experiments, which indicate that Ag-salt/silica may be a very promising adsorbent for olefin/paraffin separation.     

Ion-exchange studies of <Superscript>110m</Superscript>Ag(I) using synthetic inorganic ion-exchanger

In the present investigation, the selective adsorption of silver on synthetic inorganic ion exchanger, zinc(II) ferrocyanide, has been established by batch method, under specific conditions, using ^110mAg as a tracer. The efficiency of adsorption has been determined by γ-ray spectrometry and was found to be greater than 96%. The Ag(I) uptake by the exchanger has also been evaluated. The selectivity of the method was checked by studying the adsorption of Ag(I) in the presence of a number of foreign ions using their corresponding tracers. The interfering ions were removed by washing the ion-exchanger with appropriate reagents, so that it could be applied for the determination of trace amount of Ag(I) in complex matrices, containing trace amount of other metal ions.     

Substrates with discretely immobilized silver nanoparticles for ultrasensitive detection of anions in water using surface-enhanced Raman scattering

Positively charged silver nanoparticles, Ag [+], obtained by UV-assisted reduction of silver nitrate using branched poly(ethyleneimine) (BPEI) and 4-(2-hydroxyethyl)-1-piperazineethanesulfonic acid (HEPES) solutions as reducing agents, were immobilized on glass surfaces to produce substrates active in surface-enhanced Raman scattering (SERS). Negatively charged silver nanoparticles, Ag [-], synthesized via a modified citrate reduction method, were also investigated for comparison. At a sparse surface coverage of 30 nanoparticles/microm(2), substrates with immobilized Ag [+] showed increasing SERS sensitivity to a variety of anions in water in the order SO(4)(2-) < CN(-) < SCN(-) approximately ClO(4)(-), with corresponding binding constants of 10(5), 3.3 x 10(5), and 10(7) (for both SCN- and ClO(4)(-)) M(-1), respectively. This order followed the Hofmeister series of anion binding in water. Significantly, substrates with Ag [+] allowed limit of detection values of 8.0 x 10(-8) M (8 ppb) and 2.7 x 10(-7) M (7 ppb) for environmentally relevant perchlorate (ClO(4)(-)) and cyanide (CN(-)) anions, respectively. In contrast, substrates with immobilized Ag [-], even upon subsequent modification by a monolayer of BPEI for positive surface charge of the nanoparticles, showed a drastically lower sensitivity to these anions. The high sensitivity of substrates with Ag [+] for anion detection can be attributed to the presence of two types of functional groups, amino and amide, on the nanoparticle surface resulting from UV-assisted fragmentation of BPEI chains. Both amino and amide provide strong binding of anions with Ag [+] nanoparticles due to the synergistic effect through a combination of electrostatic, hydrogen bonding, and dispersive interactions.     

Interaction between Pd and Ag on the surface of silica

Palladium, silver and palladium–silver catalysts supported on silica were prepared by coimpregnation of support with solution of AgNO₃ and Pd(NO₃)₂. The catalysts were characterized by X-ray powder diffraction (XRD), temperature programmed reduction (TPR), time of flight ion mass spectrometry (ToF-SIMS), chemisorption of carbon monoxide and were tested in the reaction of selective oxidation of glucose to gluconic acid.

XRD and TPR studies have shown that an interaction between Pd and Ag on the surface of silica after oxidation at 500 °C and reduction at 260 °C leads to the formation of solid solutions.

ToF-SIMS images of the surface of 5% Ag/SiO₂ catalyst after oxidation at 500 °C and reduction at 260 °C show that Ag atoms supported on silica are not distributed homogenously but tend to form regions of enhanced Ag concentration. Positive ions images of the surface of 5% Pd/SiO₂ catalyst also display regions of enhanced concentration of Pd atoms, but they are more homogenously distributed on silica.

ToF-SIMS peak intensity ratio ¹⁰⁸Pd⁺/¹⁰⁷Ag⁺ for bimetallic 5% Pd–5% Ag/SiO₂ catalysts has a lower value than that obtained for physical mixture 5% Pd/SiO₂–5% Ag/SiO₂ which indicates that the surface of bimetallic catalyst is enriched with silver atoms.     

Effect of transition metal oxide additives on the activity of an Ag/SiO2 catalyst in carbon monoxide oxidation

The catalysts of silver supported on mesoporous silica modified with Co₃O₄, CeO₂, and ZrO₂ were prepared by an impregnation method; characterized by X-ray diffraction analysis, temperature-programmed reduction, and low-temperature nitrogen adsorption; and studied in a model reaction of CO oxidation. It was found that the Ag/SiO₂ system exhibited high activity in the reaction of CO oxidation, and the addition of transition metal oxides led to reduction of the temperature of 50% CO conversion by 40°C. The modification of Ag/SiO₂ with cerium dioxide was found most effective because of the interaction of silver particles and CeO₂ on the surface of silica gel.     

在线固相氧化物吸附-火焰原子吸收法测定痕量银

基于硅胶表面对碱性体系中新生成的氧化银(Ag2O)的有效吸附, 建立了流动注射-固相氧化物分离富集-火焰原子吸收法测定痕量银的方法. 当银以氧化物的形式被滞留在硅胶固相表面时, 硅胶表面的硅醇基和表面电荷有利于反应体系中新生成的Ag2O胶状沉淀的吸附, 将收集的沉淀用HNO3(10%, 体积分数)洗脱后用火焰原子吸收测定. 当进样体积为5.4 mL时, 测得的富集系数为25.5, 检出限为0.6 μg/L, 采样频率为50次/h, 线性范围为2~150 μg/L, 相对标准偏差(RSD)为2.0%(40 μg/L, n=11). 将该法用于自来水、河水、井水、雪水和山泉水中银含量的测定, 加标回收率分别为93.3%, 89.5%, 96.6%, 108.4%和102.8%.     

Synthesis and catalytic activity of porous blocked Ag/SiO2 composites in low-temperature carbon monoxide oxidation

The Ag/SiO₂ composites were synthesized based on porous blocked silica with a pore size of 30–50 nm and a specific surface area of 99 m²/g. Silver particles were introduced into the pores of the support by its impregnation with a solution of an ammonium complex of silver followed by reduction with hydrogen. The liquid-phase reduction of silver ions in pores was performed in the absence of stabilizing agents with the use of ethylene glycol (a polyol method) or formamide as a reducing agent. The methods used in the preparation of composites made it possible to vary the particle size of silver. The greatest size that is almost comparable with the pore size was achieved with the use of formamide. The catalytic activity of the Ag/SiO₂ composites was studied in the reaction of CO oxidation. It was found that the catalysts obtained upon the reduction of Ag⁺ ions by formamide exhibited considerable low-temperature activity. A necessary condition for the manifestation of low-temperature activity is redox treatment, in the course of which the particle size of silver considerably decreases.     

Cyclic voltammetry on Ag(111) and Ag(100) faces in sodium hydroxide solutions

The electrochemical behavior of silver (100) and (111) single crystal surfaces was examined by cyclic voltammetry in aqueous NaOH solution. In the `double layer' region (between −1.2 and 0.1 V (SCE)) adsorption of OH⁻ ions followed by phase transformation into an Ag–OH monolayer was found to take place. The difference in peak potentials recorded in 0.1 and 0.01 mol dm⁻³ NaOH solutions of about 60 mV indicates that one electron is exchanged in the overall electrochemical reaction, implying a complete charge transfer between OH⁻ ions and the silver surface. The adsorption process has been modeled to a Frumkin adsorption isotherm. Further oxidation of silver into Ag₂O takes place at more positive potentials. The formation of bulk Ag₂O results in considerable change to the original single crystal surface. This is likely to be due to roughening of the silver surface as a consequence of the formation and reduction of the oxide.     

Reversible oxidation/reduction of silver supported on silica aerogel: Influence of the addition of phosphate

Ag/SiO₂ and Ag₃PO₄/SiO₂ systems supported on silica aerogel were investigated using temperature-programmed reduction (TPR), UV-visible diffuse reflectance spectroscopy (UV-vis DRS), and infrared spectroscopy. The formation of highly dispersed silver particles, uniformly distributed along the surface and stabilized with silanol groups, was observed for Ag/SiO₂ system. Phosphate and silanol groups produce two states of silver localization in phosphate-containing system. The addition of phosphate onto the silica surface leads to the reversible oxidation/reduction of silver in the temperature range of 100–300°C with transitions of silver (particles 10–30 nm in size) to charged states (ions, clusters stabilized by phosphate groups). This reversible behavior of silver is stable, and the amount of silver involved in these processes remained constant (∼50%) for the series of consistent cyclic oxidation/reduction treatments.     

Solid phase extractors derived by functionalising sub-micro silica gel with chelating agents and their pH-tunable adsorbing capability towards Pb(II) and Ag(I)

Three novel solid phase extraction agents were developed by functionalising sub-micron sized silica gel with organic functional moieties possessing {SN}-ligating atoms. The extractors were characterised by FTIR and TGA. Their capability of adsorbing the ions Fe(III), Cu(II), Zn(II), Cd(II), Cr(VI), Hg(II), Pb(II), Co(II), Ni(II), and Ag(I) is described. The extractors show pH-tunable selectivity for Ag(I) and/or Pb(II). By adjusting the pH to 5 or 6, high affinity is found for both Ag(I) and Pb(II), with little or no interference by the other metal ions. At pH values of <2, the extractors become highly selective for Ag(I), with an adsorption capacity of 35 mg g^?1. Little mechanical stirring is required due to the size of the particles. The recovery rates for both Ag(I) and Pb(II) were better 90% even after five repetitive adsorption-desorption cycles.     

Highly Efficient Visible Light Plasmonic Photocatalyst Ag@Ag(Br,I)

The new plasmonic photocatalyst Ag@Ag(Br,I) was synthesized by the ion‐exchange process between the silver bromide and potassium iodide, then by reducing some Ag⁺ ions in the surface region of Ag(Br,I) particles to Ag⁰ species. Ag nanoparticles are formed from Ag(Br,I) by the light‐induced chemical reduction reaction. The Ag@Ag(Br,I) particles have irregular shapes with their sizes varying from 83 nm to 1 μm. The as‐grown plasmonic photocatalyst shows strong absorption in the visible light region because of the plasmon resonance of Ag nanoparticles. The ability of this compound to reduce Cr^VI under visible light was compared with those of other reference photocatalyst. The plasmonic photocatalyst is shown to be highly efficient under visible light. The stability of the photocatalyst was examined by X‐ray diffraction and X‐ray photoelectron spectroscopy. The XRD pattern and XPS spectra prove the stability of the plasmonic photocatalyst Ag@Ag(Br,I).     

Smart synthesis of silver nanoparticles supported in porous polybenzoxazine nanocomposites via a main-chain type benzoxazine resin

Novel silver nanoparticles immobilized on macroporous polybenzoxazine nanocomposites were prepared as catalysts for catalytic reduction reaction.     

Development of a novel electrochemical cell for slab optical waveguide spectroscopy for in situ observation of methylene blue and anions on an electrode/electrolyte interface

A new spectroelectrochemical cell for slab optical waveguide (SOWG) spectroscopy was developed in order to observe in situ an electrode/electrolyte interface for bulk electrolysis. The new SOWG spectroelectrochemical cell has been evaluated by simultaneous electrochemical-absorption experiments of methylene blue (MB) using cyclic voltammetry (CV) and SOWG spectrometry. CV was performed in the SOWG spectroelectrochemical cell using indium tin oxide (ITO) coated glass as the working electrode, platinum wire as the counter electrode and a silver/silver chloride electrode (Ag/AgCl) as the reference electrode. Based on the CV and SOWG spectrometric data, it was found that the SOWG spectra showed the MB spectra on the electrode surface selectively and that SOWG with the cell would be useful as a tool for in situ study of an electrode/electrolyte interface. Using this cell, the effects of the supporting electrolytes, NaNO₃, KNO₃, CH₃COONa, and CH₃COOK on the absorbance of MB were examined at the potential of +0.8 V versus Ag/AgCl. The decrease in MB absorbance by nitrate ions was greater than that of acetate ions. Therefore the competitive adsorption of nitrate ions was stronger than that of acetate ions. Thus, the decrease in absorbance of MB in the presence of anions demonstrates the competitive adsorption of anions. These results show that the extent of specific adsorption of electrolytes was observed by measuring the SOWG absorbance intensity of MB.     

Preconcentration and electroanalysis of silver at pt electrode modified with poly(2-aminothiazole)

Conducting poly(2-aminothiazole) (PAT) films were electrodeposited on a platinum disc electrode surface by constant potential electrolysis of 2-aminothiazole (AT) for the stripping voltammetric determination of Ag(I). Ag(I) was preconcentrated on the polymer matrix by dipping the modified Pt electrode (PAT-Pt electrode) into Ag(I)(aq) solution. Effects of the film thickness, reduction potential, pH, preconcentration time, Ag(I) concentration and the interference of some other metal ions on the oxidation peak current of silver were studied. Cu(II) interference observed to be significant for the stripping voltammetric determination of Ag(I). The detection limit was calculated on the basis of signal to noise ratio of 3 as 2 × 10^?7 mol L^?1.     

Photochemical deposition of SERS active silver nanoparticles on silica gel and their application as catalysts for the reduction of aromatic nitro compounds

We report an impregnation technique for immobilization of silver(I) gelatin complex on silica gel. Subsequent UV exposure of the dry impregnated silica gel deposited silver nanoparticles on the solid matrix. Conventional techniques (UV-visible spectroscopy, TEM, EDAX, and thermal analysis) have been used to identify and characterize silver particles on silica surfaces. The photoproduced silver particles have shown unique SERS activity that authenticates the presence of silver nanoclusters in the silica matrix. Hence, the surface of the silica matrix remains SERS-active for months. This surface activity of the silica matrix inspired us to successfully study the catalytic reduction of nitro-compounds in aqueous, organic, and three different micellar media. Different thermodynamic parameters for the reduction processes have also been evaluated. Catalytic activity of the particles in micelles is explained in the light of hydrophobic and electrostatic interactions between the substrate and the micelles.