超声无皂乳液聚合制备AMPS/MMA二元共聚微球

在不加任何引发剂和乳化剂的条件下,用超声辐射无皂乳液聚合合成了AMPS/MMA二元共聚微球,用FTIR、TGA-DSC、TEM和粒度分析仪等测试技术对产物结构和热性能分别进行了表征和测试,并初步探讨了聚合反应机理. 结果表明,超声波功率为200 W,在45 ℃反应75 min后转化率达83%,合成得到的高分子微球分散均匀,粒径在0.77 μm左右,Tg为120 ℃.     

以2-苯基-4,4'-二氨基二苯醚为基础的热固性聚酰亚胺树脂及其复合材料

以2-苯基-4,4'-二氨基二苯醚(p-ODA)、异构二苯醚二酐(ODPA)和苯乙炔基苯酐(PEPA)为原料,通过两步法合成了聚合度分别为1,2和3的酰亚胺树脂低聚物,并通过模压成型法制备了单向碳纤维增强的聚酰亚胺复合材料.表征了酰亚胺树脂低聚物的溶解性、熔体黏度及其固化物聚酰亚胺树脂的热性能,结果表明,聚酰亚胺树脂具有良好的溶解性,在N,N-二甲基乙酰胺(DMAc)、四氢呋喃(THF)及1,4-二氧六环等溶剂中的溶解度大于30%;所有酰亚胺树脂低聚物的最低熔体黏度均在10 Pa·s以下,具有良好的成型工艺性;聚酰亚胺树脂具有良好的热性能,玻璃化转变温度(Tg)最高可达300℃,5%热失重温度(T5%)最高可达545℃,碳纤维增强聚酰亚胺复合材料PIC-4,4'-ODPA-2具有最佳的高低温力学性能.     

乙酸中沉淀聚合制备窄分散聚二乙烯基苯微球

在沉淀聚合中利用含无毒的乙酸溶剂合成出窄分散交联聚二乙烯基苯(PDVB-55)微球,用扫描电镜(SEM)对其表面形态和粒度进行了表征,结果显示PDVB-55微球均匀且互相分离,平均粒径是2.69μm.X射线光电能谱(XPS)分析表面化学组成显示,微球表面有大量残余双键.     

无孔双马来酰亚胺树脂微球的制备

无孔双马来酰亚胺树脂微球的制备;聚醚酰亚胺;双马来酰亚胺树脂;相结构;微球     

微乳液成核-离子交联制备阿司匹林/壳聚糖纳米微球及其体外释放行为

以自制阿司匹林为药物模型,壳聚糖(CS)为载体源,采用微乳液成核-离子交联法制备了阿司匹林/壳聚糖纳米缓释微球.分别用傅里叶变换红外(FTIR)光谱、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、动态激光光散射(DLLS)、X射线粉末衍射(XRD)等表征了纳米微粒的化学组成、外观形貌、平均粒径和粒径分布、微球中壳聚糖的晶体结构以及阿司匹林的分布形态.结果表明,利用微乳液成核-离子交联法制备的阿司匹林/壳聚糖微球平均粒径约为88nm且粒径分布均匀,成核后壳聚糖结晶形态基本未变,阿司匹林以分子形态分布于微粒中,分子间未形成堆砌,为无定形态.采用UV-Vis分光光度计考察了微球的药物包封率、载药量,并对微球在生理盐水和葡萄糖溶液中的释药行为进行跟踪.结果表明,微球的载药量可达55%,药物包封率可达42%,实验条件下具有较好的药物缓释作用.     

用于固定抗体的新型温敏性核—壳结构聚合物微球的合成及其初步应用研究

利用无皂乳液聚合和种子聚合的方法合成了一种以聚苯乙烯为核,聚(N-异丙基丙烯酰胺-co-N-丙烯酸琥珀酰亚胺酯)为壳的单分散的核-壳结构的聚合物微球.用扫描电镜和透射电镜观察了球的形貌特征,发现微球具有清晰的核-壳结构和较好的单分散性,红外光谱显示了在1738cm-1处有酯羰基的特征吸收峰.动态光散射测定发现该聚合物微球具有温敏性,当温度高于聚N-异丙基丙烯酰胺的最低临界溶液温度(LCST)时,球的流体力学直径变小.利用微球壳层所含有的琥珀酰亚胺酯基与伯氨基的高反应活性,将抗体Rabbit IgG化学固定在球的壳层上.由于壳层的聚N-异丙基丙烯酰胺具有温敏性,反应温度不同结合的抗体的量也不同,在0℃和36.5℃,微球对抗体的结合率分别为61.6%和38.6%.     

反相非水乳液法制备聚酰亚胺微球

在N,N-二甲基甲酰胺(DMF)/Pluronic-F127、十二烷基苯磺酸钠(SDBS)/液体石蜡(LP)反相非水乳液体系中,以均苯四甲酸二酐(PMDA)和4,4′-二氨基二苯醚(ODA)为单体合成聚酰胺酸(PAA),采用吡啶/乙酸酐脱水剂,对PAA化学酰亚胺化,并进一步热酰亚胺化,制得PI耐热微球.产物通过红外、热重、扫描电镜表征.结果表明,较高的固含量和良好的乳液分散性有利于PI微球的形成;反相非水乳液体系稳定的配比条件是,VDMF∶VLP为1∶4,MF127∶MSDBS为3:2,乳化剂用量为9 wt%;在此配比条件下,当固含量为20%,热酰亚胺化温度不高于330℃时,可制得分散良好、球形规整、高热稳定性的PI微球,其粒径约为10μm.     

种子乳胶粒表面修饰法制备核壳结构PSt/TiO_2复合微球

首先采用无皂乳液聚合法合成了表面带负电荷、粒径为360 nm的单分散聚苯乙烯(PSt)乳液,并利用聚乙烯亚胺(PEI)在25℃下对PSt乳胶粒表面进行修饰,得到了表面带有正电荷的PSt种子乳液;然后以乙醇和水的混合物为反应介质,采用种子乳液加入法,使钛酸正丁酯(TBT)在修饰后的乳胶粒表面进行水解与缩合,制备出了核壳结构PSt/TiO2复合微球,利用电镜对复合微球的结构形态进行了表征.结果表明,PSt乳液改性时体系的zeta电位随着PEI用量的增加而升高,当PEI用量为PSt聚合物重量的15%时,体系的zeta电位从原来的-40.3 mV升高到了38.3 mV,达到对PSt乳胶粒表面改性的最佳值;在制备PSt/TiO2复合微球时,TiO2包覆量随着反应时间的延长而增加,反应7 h时达到90.2%的最大值;随介质中水含量的增加,吸附到复合微球表面上的TiO2纳米颗粒逐渐减少,复合微球表面逐渐变得光滑,当EtOH/H2O质量比为100/6.0时,得到结构均一、壳层厚度为29 nm的核壳结构PSt/TiO2复合微球.     

耐高温端乙炔基聚醚酰亚胺改性含硅芳炔树脂

采用预共聚法,以含硅芳炔树脂(PSA)和端乙炔基聚醚酰亚胺(PEI)为原料,制备了端乙炔基聚醚酰亚胺改性的含硅芳炔(PEI-PSA)树脂及其与T300碳纤维平纹布的复合材料T300/PEI-PSA。通过动态热机械分析(DMA)和X射线能谱仪(EDS)研究了溶剂、溶液浓度、反应温度对预共聚反应的影响,确定了预共聚反应的最佳条件,得到了均匀分散的PEI-PSA树脂。通过红外光谱(FT-IR)、核磁共振氢谱(1 H-NMR)、差示扫描量热(DSC)、热失重(TG)、DMA和EDS等表征了PEI、PEI-PSA树脂及T300/PEI-PSA复合材料的结构和性能。结果表明,当PEI质量分数为20%时,PEI-PSA树脂浇铸体的弯曲强度达44.5 MPa,较PSA树脂浇铸体提高了90.2%;T300/PEI-PSA复合材料的弯曲强度达602.7 MPa,较T300/PSA复合材料的弯曲强度提高了124%。     

甲基取代的聚芳醚酮酮酰亚胺树脂的合成与性能

N,N′-(4,4′-二苯甲烷)-二偏苯三甲酰亚胺酰氯(DIDC-M)与4,4′-二(2-甲基-苯氧基)三苯二酮(o-Me-DPOTPDK) 进行低温溶液共缩聚,制备了甲基侧基取代的聚芳醚酮酮酰亚胺(o-Me-PEKKI)聚合物.用FT-IR,1H-NMR,DSC,TG 和WAXD对聚合物的结构和性能进行了表征.研究表明:聚合物为非晶态结构;具有较高的玻璃化转变温度(Tg:241 ℃)和较好的耐热性能(Td:487 ℃);能溶解于间甲酚、NMP、氯仿、四氯乙烷等有机溶剂中.     

Biodegradable heparin-loaded microspheres: carrier molecular composition and microsphere structure

Microspheres of amphiphilic triblock polymers PLLA-PEG-PLLA were investigated as carriers for heparin delivery. Two series of PLLA-PEG-PLLA triblock were synthesized and prepared into microspheres with heparin loaded. The microspheres were hollow and the surface morphology varied from smooth to porous. The pore size increased with increasing PEG content. The microsphere size distribution showed that higher PEG content increased the average microsphere size. The release rate of heparin was closely related to the surface morphology of the microspheres. DSC spectra showed that both cold crystalline temperature (Tc) and crystalline melting temperature (Tm) of heparin-loaded microspheres were related to the copolymer composition and the Tc was lower than those of corresponding pure microspheres. [IMAGES: SEE TEXT]     

Preparation and characterization of novel cyanate ester/epoxy resin microspheres

A novel kind of cyanate ester (CE)/epoxy resin microspheres have been synthesized using the polymerization technology of cyanate ester and epoxy resin in anhydrous ethanol media; surfactant sodium dodecylbenzene sulfonate was used as an emulsifier, and imidazole was used as catalyst or curing agent. The morphologies, chemical structures, and thermal properties of microspheres were investigated by Fourier transform infrared spectroscopy, scanning electron microscope, laser scanning confocal fluorescence microscopy, optical microscope, differential scanning calorimeter, and thermogravimetric analyzer, respectively. The effects of process parameters such as the amount of imidazole and the weight ratio of epoxy resin to CE on the size and morphology of microsphere were discussed. Results indicate that the reactivity and surface morphology of microsphere can be adjusted by the amount of imidazole and the weight ratio of epoxy resin to CE. The prepared microsphere shows excellent thermal stability and good reactivity.     

Synthesis and characterization of heat-stabilized albumin magnetic microspheres

Human serum albumin magnetic microspheres containing 30% iron oxide particles were synthesized by a heat-stabilization process. The average diameter, the size distribution and the morphology were characterized by scanning electron microscopy, atomic force microscopy and transmission electron microscopy. The distribution of the iron oxide nanoparticles within the microspheres was confirmed by the contrast obtained in the morphology by backscattered electron imaging in scanning electron microscopy. Energy-dispersive X-ray spectroscopy showed the presence of iron in the microspheres. The cabbage like surface structure in some of the microspheres obtained in scanning electron microscopy can be better understood by atomic force microscopy. This peculiar surface structure in the microsphere may be due to the cross-linking in the protein molecule by heat. The amount of iron oxide in the microsphere was analyzed by atomic absorption spectroscopy. The magnetic properties of the particles were measured in a superconducting quantum interference device magnetometer. Received: 12 September 2000 Accepted: 5 February 2001     

双酚A型环氧树脂多孔微球

双酚Ａ型环氧树脂多孔微球杨振忠许元泽俞浩赵得禄（中国科学院化学研究所高分子物理开放实验室北京１０００８０）关键词多孔微球，双酚Ａ环氧树脂，相反转技术微米级高分子多孔微球在生物医学、电子、印刷、信息业等方面具有重要作用．然而，通常的乳液聚合，悬浮聚合...     

带羧基单分散彩色微球的制备

采用两步活性溶胀种子聚合法, 制备了可用于免疫检测的3种不同颜色的表面带有羧基功能基的粒径在400—800 nm之间的彩色单分散微球. 先用无皂乳液聚合法制备出单分散聚苯乙烯种子, 然后用邻苯二甲酸二正丁酯(DBP)作为溶胀剂对微球进行溶胀, 溶涨后的种子模板再用混溶的苯乙烯、二乙烯苯、丙烯酸、双键彩色染料以及引发剂(BPO)溶胀, 升温聚合后得到理想的单分散微球. 考察了DBP和单体用量、各单体配比及染料对微球的形貌和单分散性的影响.     

离子凝胶反应法制备壳聚糖/N,O-羧甲基壳聚糖微球

以一氯乙酸与壳聚糖反应形成N,O-羧甲基壳聚糖两性聚电解质,分光光度法测定其等电点IEP=2．86。以此两性聚电解质与壳聚糖可以在一定条件下形成微球,光学显微镜和电子显微镜测试表明,控制两种聚电解质配比可以制备不同粒径大小的微球,而超声功率对微球粒径的影响较小。红外光谱测试表明微球中N,O-羧甲基壳聚糖羧基以羧酸根形式存在,分光光度与电导法联合测定表明两种聚电解质以离子凝胶作用形成微球,其最佳制备条件为IEP（CM-CHITOSAN）〈pH〈pKa（CS）,在此较宽的pH值范围内微球可稳定存在。     

INVESTIGATION OF POLYDL-LACTIDE-b-POLY（ETHYLENE GLYCOL）-b-POLYDL-LACTIDE MICROSPHERES CONTAINING PLASMID DNA

PolyDL-lactide (PDLLA) and the block copolymer, polyDL-lactide-b-poly(ethylene glycol)-b-polyDL-lactide (PELA) were used as the microsphere matrix to encapsulate plasmid DNA. The PDLLA, PELA, pBR322-1oaded PDLLA and pBR322-1oaded PELA microspheres were prepared by solvent extraction method based on the formation of multiple w1/o/w2 emulsion. The microspheres were characterized by surface morphology, mean particle size, particle size distribution and loading efficiency. The integrity of DNA molecules after being extracted from microspheres was determined by agarose gel electrophoresis. The result suggested that plasmid DNA molecules could retain their integrity after being encapsulated by PELA. The PELA microspheres could prevent plasmid DNA from being digested by DNase. The in vitro degradation and release profiles of plasmid DNA-loaded microspheres were measured in pH - 7.4 buffer solution at 37℃. The in vitro degradation profiles of the microspheres were evaluated by the deterioration in microspheres surface morphology, the molecular weight reduction of polymer, the mass loss of microspheres, the changes of pH values of degradation medium, and the changes of particle size. The in vitro release profiles of the microspheres were assessed by measurement of the amount of DNA presented in the release medium at determined intervals. The release profiles were correlation with the degradation profiles. The release of plasmid DNA from PELA microspheres showed a similar biphasic trend, that is, an initial burst release was followed by a slow, but sustained release.     

Effect of molecular weight on reaction-induced phase separation of epoxy resin modified with fluorocarbon chain terminated polyetherimide

Epoxy resins are currently used for many important applications such as adhesives, encapsulates and ad-vanced composite matrixes. However, the further use of epoxies is limited because of their inherent brittle-ness. Thus, the modifications of epoxy resin…     

Preparation and characterization of biodegradable microspheres containing hepatitis B surface antigen

Poly-DL-lactide-poly(ethylene glycol) (PELA) microspheres containing Hepatitis B surface antigen (HBsAg) were elaborated by a solvent extraction method based on the formation of a double water/oil/water (w/o/w) emulsion. Microspheres were characterized in terms of morphology, size and size distribution, encapsulation efficiency, and the efficiency of microsphere formation (EMF). Transmission electron microscopy (TEM) and polyacrylamide gel electrophoresis (PAGE) were used to investigate the structural integrality of HBsAg encapsulated in PELA microspheres. The release profile was investigated by the measurement of antigen present in the release medium at various intervals. The PELA-10 microspheres displayed the highest antigen encapsulation efficiency (about 80%), and antigen molecules could be stabilized in the PELA-10 microspheres during the preparation process. It suggested that the PELA microspheres had a great potential as a new polymer adjuvant for HBsAg. The release of Hepatitis B surface antigen from poly-DL-lactide-poly(ethylene glycol) microspheres.     

Effect of preparation temperature in solvent evaporation process on Eudragit RS microsphere properties

Eudragit RS 100 microspheres containing ketoprofen as a model drug were prepared by the solvent evaporation method using an acetone/liquid paraffin solvent system. The influence of various preparation temperatures: 10, 25, 35, and 40 degrees C, on particle size and morphology, drug content and release kinetics, and drug crystal state was evaluated. With increasing temperature, microsphere average size was found to increase and particle size distribution to widen significantly. At 10 degrees C particles of irregular shape are formed, whereas higher temperatures gradually improve the sphericity of microspheres. As can be seen from SEM photographs, particle surface roughness decreases as preparation temperature increases. It was found that temperature had no effect either on ketoprofen microencapsulation efficiency or on its crystal state, but it does influence emulsion-stabilizer incorporation. Ketoprofen forms solid solution in Eudragit matrix and maintains amorphous state for significant period of time. Drug release rates from microspheres correlated with microspheres' surface roughness and to a lesser extent with particle size.