碱金属盐LiCl对聚酰亚胺微球化的影响

以两步法为基础,采用非水乳液体系,先通过单体聚合得到聚酰胺酸溶液(PAA),然后经酰亚胺化使PI微球化,成功得到PI微球。利用傅立叶变换红外光谱(FT-IR)、扫描电子显微镜(SEM)、热失重分析仪(TGA)等手段表征了PI微球的化学结构和微观形貌,探讨了在制备过程中加入碱金属盐LiCl对PI微球化形态的影响。研究结果表明,LiCl的加入使得PI微球聚集态形貌出现孔隙结构,而当LiCl浓度达到临界点时,聚合物基体的孔隙率增加,形貌呈均匀的微孔状"海绵"结构。此外,通过热分析得出,Li盐的加入对微球的热稳定性几乎没有影响。     

反相非水乳液制备多孔聚酰亚胺微球

在Span85/N,N-二甲基甲酰胺/液体石蜡稳定反相非水乳液体系中,以均苯四甲酸酐和4,4’-二氨基二苯醚为单体,选用甲醇、二硫化碳作为致孔剂,制备多孔聚酰亚胺(PI)微球.通过SEM、量子化学模拟、粒径测试等手段考察致孔剂种类、致孔剂用量、吡啶/酸酐滴加速度及反应温度和单体浓度对致孔的影响.结果表明,选用二硫化碳、甲醇为致孔剂时所制得的微球形貌良好,但CS2为致孔剂时,所得到的微球孔道很少;而甲醇为致孔剂时,则得到了孔道明显的多孔PI微球.致孔的最佳条件为反应温度20℃,单体浓度10%,吡啶/酸酐滴加速度0.5 s/滴时,才可得到的形貌良好、分布均一的多孔PI微球.而且随着甲醇/液体石蜡的体积比增加,多孔PI微球比表面积也随着增大,最大可达29.38 m2/g.所得产物粒径分布在20~30μm之间,热稳定性良好,其起始热分解温度为517℃.     

聚酰亚胺/聚丙烯腈共混黑膜的制备及其结构与性能

采用共混的方法制备聚酰胺酸/聚丙烯腈(PAA/PAN)共混溶液.其中2种PAA溶液分别由二酐(3,3′,4,4′-联苯二酐(BPDA)与均苯四甲酸二酐(PMDA))和二胺(对苯二胺(PDA)与4,4′-二氨基二苯醚(ODA))均聚或共聚而得,N,N-二甲基乙酰胺(DMAc)为溶剂,PAN溶于DMAc中制成溶液后与PAA溶液混合,涂膜后热处理制得聚酰亚胺(PI)/PAN共混薄膜.分析了PAA和PAN在热处理过程中的变化,以及PAN的加入量对共混薄膜的结构与性能的影响.结果表明,在热处理过程中,PAA完成了亚胺化成为PI,而PAN完成了预氧化,形成了稳定的梯形结构,制备出具有良好力学性能、黑色、不透光的薄膜,但是随着PAN含量的增加,体系发生明显的相分离,薄膜力学性能有所下降,(BPDA/PDA/ODA)PI中加入10%的PAN和(PMDA/ODA)PI中加入20%的PAN时能获得具有良好力学性能的黑色、低透光率的薄膜.     

CTAB反相微乳液的稳定条件与纳米WO3的制备

以CTAB(十六烷基三甲基溴化铵)/正丁醇/正辛烷/钨酸钠水溶液构制反相微乳体系,通过测定体系电导率的方法确定相点并绘制反相微乳区拟三元相图。考察了该体系在不同条件下稳定存在的组成范围,选取实验最佳条件制备出纳米WO3。结果表明,表面活性剂与助表面活性剂的比、钨酸钠溶液的浓度对该反相微乳体系稳定区域的影响较大,当m(CTAB)∶m(正丁醇)=1∶2,钨酸钠浓度为0.05～0.08 g/mL时,体系有较大的反向微乳区,且当m(CTAB 正丁醇)∶m(正辛烷)=2∶3时,体系有最大溶水量;温度对该体系稳定区域的影响不大。在最适宜条件下,以0.08 g/mL的钨酸钠微乳液与盐酸微乳液,在40℃的水浴中反应7 h,制备出平均粒径约30 nm的WO3纳米粒子。     

在CPS微球表面实现N-羟基邻苯二甲酰亚胺的同步合成与固载及固体催化剂催化氧化性能初探

通过分子设计的构思,仅通过两步大分子反应,便实现了N-羟基邻苯二甲酰亚胺(NHPI)在交联聚苯乙烯(CPS)微球表面的同步合成与固载,并制得了非均相催化剂微球CPS-NHPI。以氯化偏苯三酸酐(TMAC)为试剂、Lewis酸为催化剂,通过Friedel-Crafts酰基化反应,先将邻苯二甲酸酐(PA)基团键合在CPS微球表面,得到改性微球CPS-PA;再与盐酸羟胺进行酰亚胺反应,制备出固载有NHPI基团的非均相催化剂微球CPS-NHPI。重点研究了CPS微球表面发生Friedel-Crafts酰基化反应的影响因素。采用红外光谱(FT-IR)及扫描电子显微镜(SEM)等对微球CPS-NHPI进行表征,将微球CPS-NHPI分别用于分子氧氧化乙苯及环己烷两种烃类物质的氧化过程,初步考察了该微球的催化活性。研究结果表明,对于微球CPS与TMAC之间的FriedelCrafts酰基化反应,适宜的溶剂为氯仿与N,N-二甲基乙酰胺(DMAC)混合溶剂(氯仿与DMAC的体积比为7∶3),适宜的Lewis酸催化剂为SnCl4。初步探索实验表明,催化剂微球CPS-NHPI与Co(OAc)2所构成的共催化体系,在分子氧氧化乙苯及环己烷的催化氧化过程中,都表现出了良好的催化活性,温和条件下,反应35h时乙苯氧化为苯乙酮的转化率可达37%,反应30h时环己烷氧化为环己酮的转化率可达21%。     

复配乳液体系中聚氯甲基苯乙烯纳米颗粒的制备

以初始质量分数为21.4%的氯甲基苯乙烯,在十二烷基苯磺酸钠(LAS)/聚醚复配乳液体系中制备了粒径为65.0nm,单分散性良好的聚氯甲基苯乙烯纳米微球.用红外光谱仪、透射电子显微镜、Zeta电位粒度仪测试技术对产物的化学结构、粒径大小、形貌、单分散性进行了表征.结果表明,在复配乳液体系中可以在提高单体含量的同时,保持产物的粒径在纳米级,同时体系的稳定性良好.透射电子显微照片显示,制得的纳米微球之间存在黏连.并提出了氯甲基的存在可能是产生这种现象的原因.     

油酸-正丙醇-水无表面活性剂反相微乳液电导研究

本文对油酸-正丙醇-水三元体系的相行为进行了研究,表明可形成微乳液.由于体系中无传统表面活性剂,故所形成的微乳液为无表面活性剂微乳液.在反相微乳液区,固定正丙醇/油酸体积比(RP/O)为3∶5、1∶1和2∶1,考察了体系电导率(κ)随分散相体积分数(φd)的变化,结果表明κ随φd的增大先缓慢增加,后急剧增大,符合渗滤特...     

以单分散P(DC-TMPTA)聚合物微球为Pickering乳液稳定剂制备石蜡乳液和石蜡微球

以三羟甲基丙烷三丙烯酸酯(TMPTA)和1-十二烯(DC)为单体,不使用任何乳化剂或分散稳定剂,通过沉淀聚合制备了高度单分散P(DC-TMPTA)的聚合物微球颗粒.以此聚合物微粒为Pickering稳定剂,不添加任何化学助剂,以乙醇-水混合介质在70℃下通过恒速振荡制得了单分散石蜡Pickering乳液.将该体系迅速降温至石蜡熔点之下,制得了窄分布的固体石蜡微球.研究了连续相水含量、振荡频率及稳定粒子尺寸对Pickering乳液及石蜡微球的影响,优化了石蜡乳液和微球的制备条件.利用扫描电子显微镜对石蜡微球的表面和内部形貌进行了表征,结果表明P(DC-TMPTA)微球全部聚集在石蜡液滴和固化后的石蜡微球表面.基于石蜡微球和聚合物稳定粒子的尺寸,计算了不同条件下石蜡微球表面聚合物粒子的数量.通过聚合物粒子在石蜡-乙醇和水混合溶液界面的三相接触角以及石蜡-乙醇和水混合溶液界面张力的测定,计算了聚合物粒子在石蜡-乙醇和水混合溶液界面吸附能,为解释该体系Pickering乳液的稳定性提供了理论支持.     

在交联聚苯乙烯微球表面同步合成与固载吡啶基卟啉及固载化钴卟啉的催化氧化性能

先通过季铵化反应将吡啶甲醛(PyAL)基团键合于交联聚苯乙烯微球(CPS)表面,制得改性微球PyAL-CPS,再通过Adler反应,成功地实现了吡啶基卟啉(PyP)在CPS微球表面的同步合成与同载,制得功能微球PyP-CPS,它再与碘甲烷发生季铵化反应制成N-甲基吡啶基卟啉(MPyP)季铵盐,从而制得固载有阳离子卟啉的...     

碳纳米管/活性炭复合微球的制备及其对VB12的吸附应用

采用反相乳液法制备碳纳米管/壳聚糖复合微球(CNTs/CTS), 并对其进一步炭化、活化制得碳纳米管/活性炭复合微球(CNTs/AC). 以此复合微球为吸附材料, 探索了其对中分子代表物质VB12的吸附. 研究结果表明, 碳纳米管含量70%(w)的复合微球经水蒸气适当活化后球形度好、吸附性能优异, 其对VB12的吸附量达23.59 mg·g-1, 分别是活性炭和大孔吸附树脂的5.4和2.7倍. 分析表明这是由于碳纳米管/活性炭复合微球具有发达的中孔结构.     

Preparation of hemispherical polyimide particles by inverse emulsion technique from poly(amic acid) ammonium salts

Nonspherical polymer particles have attracted increasing attention recently. In this paper, micron-scale hemispherical polyimide (PI) particles were fabricated using water-soluble poly(amic acid) ammonium salts (PAAS) by a novel inverse emulsion technique. In the process, liquid paraffin was used as a continuous phase, the mixed solution of PAAS and water as a dispersed phase and sorbitan monooleate (Span80) as a surfactant. The research suggested that water as a stabilizing agent played an important role in forming stable emulsion. As the amount of water increased, stability of the emulsion increased gradually and morphology of PI particles transformed from sphere to ellipsoid, and finally to hemisphere. The concentration of PAAS solution and Span80 both affected the shape of particles, which changed from spherical to hemispherical by increasing the PAAS/Span80 concentration. The mechanism of forming hemispherical PI particles was discussed based on interfacial tension and interfacial free energy changes. Via adjusting the composition of the system to change the corresponding interfacial tension, we could get the particles with different morphologies. Furthermore, the change in structure characterized by FT-IR spectroscopy demonstrated that PAAS had been converted to PI after adding the dehydrating agent to the emulsion. And TGA results showed that the obtained PI particles had excellent thermal stability.     

Preparation of nonwoven polyimide/silica hybrid nanofiberous fabrics by combining electrospinning and controlled in situ sol-gel techniques

A controlled in situ sol-gel synthesis combined with the electrospinning technique and postspun imidization was applied in the fabrication of polyimide/silica hybrid nonwoven nanofiberous fabrics with excellent thermal and mechanical performance. The nanofiberous fabrics were prepared by electrospinning of the solution of tetraethoxysilane (TEOS) and polyamic acid (PAA). The different silica contents in the fabrics were achieved by varying the amount of TEOS while fitting the solid content of PAA. The final polyimide/silica fabrics was obtained after imidization of PAA and gelation of silica phase simultaneously accomplished through a step-wise heating process. Some specific IR techniques and other characterizations indicated the successful incorporation of the silicon dioxide (SiO₂) into the PI matrix and the relatively even distribution of the SiO₂ in the fabrics. An increase of 133 °C in the decomposition temperature and 4-fold enhancement of the ultimate tensile strength were achieved for the hybrids with a 6.58 wt.% of SiO₂ content, compared to the pure PI fabric. The excellent performance could be attributed to the good compatibility between the polyimide and silica, and good adhesion among the fibers, which resulted from the controlled TEOS hydrolysis and the simultaneous imidization and gelation process.     

含硫醚结构均苯型聚酰亚胺的合成及表征

以4,4′-二氨基二苯硫醚(SDA)和均苯四酸酐(PMDA)为原料,通过溶液缩聚法-热酰亚胺/化学酰亚胺化的方法制备了一种含硫醚结构均苯型聚酰亚胺.利用高级旋转流变仪建立了在线跟踪反应进程的方法,采用热失重分析仪研究反应条件对热酰亚胺化及化学酰亚胺化法的影响,这些方法的建立为进一步制备高性能的聚酰亚胺提供有效的实验手段.采用小角激光光散射法、红外光谱、元素分析、接触角仪、DSC等方法对聚合物的结构与性能进行表征.结果显示,硫醚结构的引入,可有效改善聚合物薄膜的表面性能,其与铜箔之间的粘附功明显大于传统聚酰亚胺,在无胶挠性线路板应用方面显示出较好的应用前景.所获聚合物的Mw为(6.7±1.6)×104,分解温度均高于560℃;DSC的结果显示所制备的两种酰亚胺化聚合物均具有较高的玻璃化转变温度,相比之下,化学酰亚胺化更有利于获得高酰亚胺化程度的聚合物,产物的玻璃化转变温度也更高.     

喷雾干燥法制备水分散聚酰亚胺

利用喷雾干燥法制备了具有良好水分散性的聚酰胺酸微纳米颗粒, 其初次分散浓度可达20%, 并具有良好的再分散性. 这种微纳米颗粒经过处理后可进一步亚胺化形成透明的聚酰亚胺薄膜, 红外光谱和热失重测试结果表明薄膜已经完全亚胺化, 说明这种微纳米颗粒可应用于制备聚酰亚胺水性涂料. 同时, 对影响产物形貌的几种因素进行了初步研究.     

Structural characterization of silica modified polyimide membranes

Polyimide and hybrid polyimide‐siloxane were synthesized by polycondensation, imidization, and sol‐gel reaction. The polyimides were prepared from pyromellitic dianhydride (PMDA) and 4,4‐oxydianiline (ODA) in N‐methyl‐2‐pyrollidone (NMP). Trimethoxyvinyl silane (TMVS) was used as a source of silica. Their surface morphologies, structures and thermal performances were determined using scanning electron microscopy (SEM), infrared spectroscopy (IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results showed that the silica particles were finely and rather homogeneously dispersed in polymers. The glass transition temperature (T_g) of hybrid membrane materials increased with the increasing silica content. TGA analysis showed that polyimides were thermally stable with silica. Modified polyimide‐siloxane films, thermal characteristics were found to be better than the polyimide films without silica. Copyright © 2006 John Wiley & Sons, Ltd.     

Formation of new banded spherulites in polyimides

The crystalline morphology and structural development of aromatic polyimides during an optimum continuous thermal imidization procedure were examined by means of polarized optical microscopy and X‐ray diffraction. During thermal imidization, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride/1,3‐diaminobenzene polyimide samples formed complicated spherulites, which, in addition to zigzag Maltese crosses, also showed concentric extinction rings, which are characteristic of banded spherulites. The factors affecting the formation of banded spherulites were studied. The initial imidization conditions dramatically affected the formation of the banded spherulite morphology: slow heating (0.5 °C/min) or fast heating (20 °C/min) led to relatively small polyimide spherulites and less identifiable extinction rings. The morphological features were also affected by the molecular weight of the polyimide: higher molecular weight samples showed typical banded spherulites, whereas low‐molecular‐weight samples formed degenerated banded spherulites. In all the spherulites formed in 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride/1,3‐diaminobenzene polyimides, special zigzag Maltese crosses, instead of normal Maltese crosses, were observed. The relationship between the imidization procedure and the spherulite morphology formation was also studied. X‐ray and Fourier transform infrared together revealed that after several minutes of thermal treatment, the crystallization was nearly complete, with a 42.5% degree of crystallinity; meanwhile, only some poly(amic acid) converted to the corresponding polyimide, with a 27% degree of imidization. The crystalline morphology and structure formed in the initial stage of the imidization process were maintained during the following imidization processing at an elevated temperature. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1997–2004, 2005     

Comparative study of chromatography on thin layers impregnated with organic stationary phases. Chromatographic separation of nitrophenols.

The chromatographic behaviour of nitrophenols on thin layers of silica gel and cellulose was compared, both without impregnation and impregnated with non-aqueous polar stationary phases (formamide, dimethylformamide) and less polar stationary phases (liquid paraffin, octan-1-ol, 1-bromonaphthalene). Cellulose is preferred when using formamide or dimethylformamide if a pure partition process is required. For each particular analyte a certain amount of the stationary phase is always required to suppress the adsorption activity of silica gel. Separation by reversed-phase thin-layer chromatography is strongly affected by the type of stationary phase (the possibility of forming charge-transfer complexes with 1-bromonaphthalene) and its support (the acidic properties of silica gel and its adsorption activity), the mobile phase (content of organic modifier, pH, presence of salts) and the properties of the solutes (polarity, ionizability).     

Synthesis, photo-reaction and photo-induced liquid crystal alignment of soluble polyimide with pendant cinnamate group

In this paper, the synthesis, photo-reaction and photo-induced liquid crystal alignment of a polyimide with a pendant cinnamate group are reported. The polyimide was synthesized by the thermal imidization of the polyamic acid derived from 4,4'-(hexafluoro-isopropylidene)diphthalic anhydride and hydroxydiaminopropane, followed by the attachment of the cinnamate group to the main chain polyimide. The surface of thin layers of the polyimide was found to be preferentially occupied by the pendant cinnamate groups, and liquid crystal alignment on the polyimide thin film exposed to polarized UV was independent of the cinnamate content. The thermal stability of the photo-induced liquid crystal alignment was enhanced with decrease in the cinnamate content. This could be attributed to the strong interchain interaction of the polyimide chains which prevents thermal randomization of the photo-product of the pendant cinnamates. The dependences of the photo-reaction temperature and the annealing temperature of the alignment layer on the azimuthal anchoring energy of the photo-aligned liquid crystal suggest that the local stress developed during the UV irradiation profoundly influences the thermal stability of the liquid crystal alignment.     

水性环氧复合乳化剂的合成及性能

以环氧树脂E-44、2-氨基-5-磺酸基苯甲酸、乙二醇丁醚和正丁醇为原料,合成一种新型阴离子环氧乳化剂EP-D;同时,E-44和聚乙二醇(PEG6000)以摩尔比2∶1反应,合成端环氧基非离子环氧乳化剂EP-PEG;将EP-D与EP-PEG按不同质量比复配获得不同配比的EP-D/EP-PEG水性环氧复合乳化剂。 分别研究了EP-D/EP-PEG及EP-PEG在环氧树脂中加入质量分数为6%~12%时的乳化性能及形成乳液的表面张力、电导率和胶粒的Zeta电位、粒径。 结果表明,当EP-D和EP-PEG以质量比3∶5复配,总加入质量分数为9%时,制备的环氧乳液性能最佳。 与EP-PEG形成的环氧乳液相比,复配环氧乳化剂用量少,乳液铺展性好、稳定性高,且乳液在相反转时的固含量提高了10%以上。 复配环氧树脂乳液中胶粒的Zeta电位为-41.9 mV、粒径为342 nm、表面张力为25.5 mN/m、粘度为14 mPa·s。 这表明利用乳化剂EP-D与EP-PEG复配新合成的EP-D/EP-PEG水性环氧复合乳化剂可制备稳定性好,固含量高的乳液。     

Structure and infrared emissivity of polyimide/mesoporous silica composite films

Polyimide/mesoporous silica composite films were prepared by direct mixing of polyamic acid solution and silylated mesoporous silica particles, or by condensation polymerization of dianhydride and diamine with silylated mesoporous silica particles in N,N-dimethylacetamide, followed with thermal imidization. Structure and glass transition temperatures of the composite films were measured with FTIR, SEM, EDX, XPS and DMTA. The results show that the silylated mesoporous silica particles in the composites tend to form the aggregation with a strip shape due to phase separation. The composite films exhibit higher glass transition temperature as comparing with that of pure polyimide. It is found that the composite films present lower infrared emissivity value than the pure polyimide and the magnitude of infrared emissivity value is related to the content of silylated mesoporous silica in the composite films. Inhibiting actions of silylated mesoporous silica on infrared emission of the composite films may be owing to presence of nanometer-scale pores in silylated mesoporous silica.