聚全氟乙丙膜电子束引发预辐射接枝AA和SSS制备阳离子交换膜的研究

利用电子束引发预辐射接枝技术,在聚全氟乙丙烯(FEP)薄膜上接枝丙烯酸(AA)和对苯乙烯磺酸钠(SSS),制备一种含羧酸基团和磺酸基团的阳离子交换膜,详细研究了反应温度、单体总浓度、pH值变化、辐照气氛及添加剂对接枝率的影响规律,明确了实验条件与接枝率的对应关系。FTIR测试证明了接枝产物是全氟乙丙烯和丙烯酸、对苯乙烯磺酸钠的接枝共聚物。     

淀粉/DL-丙交酯接枝共聚物的合成和生物降解性能研究

以淀粉为接枝骨架 ,DL 丙交酯为接枝单体 ,在无水LiCl存在下 ,合成了淀粉 /DL 丙交酯接枝共聚物 .研究了接枝反应的投料比、反应时间、反应温度对单体转化率 (C % )、接枝率 (G % )和接枝效率 (GE % )的影响 .当DL 丙交酯与淀粉结构单元的摩尔比为 10∶1,反应温度为 80～ 85℃ ,反应时间为 4h ,C % ,G %和GE %可分别达到 37 3 %、179 7%和 6 8 0 % .用差示扫描量热 (DSC)分析仪、红外光谱仪和X 射线衍射仪对合成的接枝共聚物进行了表征 ,结果表明 ,淀粉和DL 丙交酯反应生成了淀粉 /DL 丙交酯接枝共聚物 .防水实验结果表明 ,该产物在给定条件下可使纸板的吸水率由 41 1%降低到 1 0 % .降解实验表明该接枝共聚物能够被酸、碱及微生物完全降解     

阳离子型接枝淀粉的合成及其絮凝性能

以玉米淀粉(St)和甲基丙烯酰氧乙基三甲基氯化铵(DMC)为原料,硝酸铈铵为引发剂,合成了阳离子型接枝淀粉St-g-PDMC,并使用IR、SEM和XRD对产物的结构进行了表征。结果表明,St-g-PDMC的最佳合成条件为m(St):m(DMC)=1:1,引发剂用量为反应物固含量的15%,反应温度60 ~oC,反应时间4 h。在此条件下合成的St-g-PDMC的氮含量为3.27%,接枝率为94.22%。以高岭土悬浊液为模拟水样测试St-g-PDMC的絮凝性能。结果表明,当模拟水样的pH=7时,St-g-PDMC的最佳用量为9 mg·L~(-1),絮凝后水样的透光率可达91.22%。     

淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

甲基丙烯酸烷基磺酸钠在嵌段聚醚氨酯膜上接枝聚合的研究

本文对两种新合成的亲水性单体,甲基丙烯酸已磺酸钠和甲基丙烯酸辛磺酸钠在聚醚氨酯膜上接枝聚合进行了研究。其反应分两步:首先,在过氧化氢存在下,将膜进行光氧化,引入过氧化氢基团;然后,在还原剂亚铁盐作用下,引发甲基丙烯酸烷基磺酸酯接枝聚合。单体浓度、亚铁盐浓度、反应温度对接枝速率均有影响。接枝膜与基膜相比,吸水率与抗凝血性能均有提高。辛酯接枝膜的抗凝血性能显得更好。用扫描电镜可观察到膜上接枝物的图象。     

接枝型偕胺肟树脂/SiO_2功能复合微粒的制备

用偶联剂γ-(甲基丙烯酰氧)丙基三甲氧基硅烷(KH-570)对微米级硅胶进行了表面化学改性,采用溶液聚合法,在改性硅胶微粒表面接枝丙烯腈(AN),制备了接枝微粒PAN/SiO2。用盐酸羟胺对接枝PAN进行偕胺肟(AO)化转变,制得了接枝有偕胺肟树脂(PAO)的复合型功能微粒PAO/SiO2。采用红外光谱(FT-IR)、热失重(TGA)及扫描电子显微镜(SEM)等测试技术,对接枝微粒PAN/SiO2以及功能微粒PAO/SiO2进行了表征,考察了制备条件对AN的接枝聚合过程及对PAN的偕胺肟化转变过程的影响规律。结果表明,适宜的接枝聚合条件为:引发剂质量分数为1.5%,反应温度为75℃。接枝聚合5h可制得接枝度为0.14g/g的接枝微粒PAN/SiO2。受偕胺肟基团空间位阻的影响,PAN的偕胺肟化转变反应不能进行彻底,适宜的PAN/SiO2偕胺肟化转变反应条件为:介质pH值为6～7,温度70℃,反应时间4h。所制得的功能微粒PAO/SiO2腈基转化率约为78%。     

微波法合成淀粉接枝丙烯酸盐类高吸水性树脂的研究

以N,N′-亚甲基双丙烯酰胺为交联剂、过硫酸铵为引发剂、在微波辐照下对淀粉接枝丙烯酸盐共聚进行了系统的研究,确定了最佳的反应条件,合成了粉末状的高吸水性树脂。并用FTIR和固体NMR等方法探讨了淀粉一丙烯酸盐接枝共聚物的结构特征。实验结果表明,利用微波技术合成淀粉一丙烯酸盐接枝共聚物可实现一次合成、干燥,简化合成工艺。淀粉与丙烯酸盐质量比为40／100左右时产物的接枝率最大,且吸水速率明显高于化学法合成的高吸水树脂。     

环氧基团功能化弹性体增韧聚乳酸的性能

以2种不同结构的弹性体乙烯-辛烯共聚物接枝甲基丙烯酸缩水甘油酯(POE-g-GMA)和乙烯-丙烯酯甲酯-甲基丙烯酯缩水甘油酯三元共聚物(E-MA-GMA)增韧聚乳酸(PLA), 研究了接枝型与嵌段型弹性体的结构对聚乳酸增韧效果的影响. 结果表明, 接枝型聚合物POE-g-GMA与基体PLA之间具有良好的界面相互作用, 当POE-g-GMA的质量分数为15%时, 共混体系的缺口冲击强度为72.4 kJ/m², 而E-MA-GMA的质量分数为15%时, 共混体系的缺口冲击强度为32.4 kJ/m², 结果表明, 接枝型聚合物POE-g-GMA增韧效果明显优于嵌段型E-MA-GMA.     

阳离子淀粉-壳聚糖-丙烯酰胺的接枝共聚研究

以硝酸铈铵为引发剂,合成阳离子淀粉(CS)-壳聚糖(CTS)-丙烯酰胺(AM)接枝共聚物,讨论了反应温度、引发剂浓度、单体用量、反应时间以及壳聚糖用量对接枝共聚反应的影响。结果表明:淀粉中葡萄糖环浓度(cAGU)为0.20 mol/L,mCTS/mCS=1/6,cAM=1.0mol/L,cCe4 =5 mmol/L,反应温度60℃,反应时间3 h时,转化率和接枝效率可分别达到88%和92%以上;转化率随mCTS/mCS增大而增大,接枝效率则随着CTS用量增大降低,CTS的存在使AM均聚的几率增大。     

苯乙烯-苯乙烯磺酸钠共聚物的制备及其流变性能

采用乳液聚合合成了一种可作为聚丙烯(PP)纤维可染改性添加剂的苯乙烯-苯乙烯磺酸钠共聚物P(St-co-NaSS)。通过傅里叶转换红外光谱仪(FT-IR)和核磁共振氢谱仪(~1 H-NMR)对共聚物的苯乙烯磺酸钠结构单元进行了表征,研究了反应条件对共聚物磺化度的影响;通过差示扫描量热仪(DSC)和热重分析仪(TG)研究了磺酸基团的引入对共聚物的玻璃化转变温度和起始分解温度的影响;通过旋转流变仪研究了磺化度对共聚物剪切黏度的影响;初步探讨了PP/P(St-co-NaSS)共混体系的染色性能。结果表明:当反应时间为2h,反应温度为70℃,引发剂质量分数为0.6%,苯乙烯磺酸钠的摩尔分数为0.01时,共聚物的磺化度f=6.68%(零切黏度η0=19 620Pa·s,属牛顿流体);在10~(-2)~10~(-1) s~(-1)的剪切速率范围内,P(St-co-NaSS)表现出假塑性流体的特征,具有较好的加工流动性。对于PP/P(St-co-NaSS)共混体系,使用阳离子染料染色时,染色深度(K/S值)为2.603 2,使用分散染料染色时,K/S值为10.168 8。P(St-co-NaSS)适合作为聚丙烯纤维的可染改性添加剂。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.