[Mn(H_2P_2O_7)_3]~(3-)引发淀粉与丙烯腈接枝聚合反应的动力学研究

以[Mn(H_2P_2O_7)_3]~(3-)为引发剂,研究了丙烯腈与玉米淀粉的接枝共聚反应。由实验结果求出了反应速率与引发剂浓度、单体浓度、淀粉浓度和反应温度的关系,推导并验证了接枝反应动力学模型,探讨了反应机理,求得了接枝反应活化能。     

粒度对多相反应动力学参数的影响

以纳米氧化锌与硫酸氢钠溶液为反应体系, 研究反应物粒度对动力学参数的影响规律. 讨论了表观活化能降低的原因. 结果表明：当反应物粒径、反应温度和搅拌速率一定时, 纳米氧化锌与硫酸氢钠溶液的反应速率仅与反应物的浓度有关；反应物粒度对多相反应的反应级数、速率常数、表观活化能和指前因子均有较大的影响；随着反应物粒径的减小, 表观活化能和指前因子减小, 而反应级数和速率常数增大, 并且速率常数和表观活化能与反应物粒径的倒数呈线性关系；反应物粒度是通过摩尔表面积、摩尔表面能和摩尔表面熵三个方面影响多相反应的动力学参数的.     

羧甲基纤维素水凝胶生物降解动力学研究

用氯化铝对羧甲基纤维素进行交联,制得了水凝胶.考察了底物浓度、酶浓度以及降解温度对该水凝胶降解速率的影响,探讨了酶降解动力学及“表观”活化能对酶浓度的依赖关系.结果表明,该酶促反应最佳温度为37 ℃,降解反应对底物浓度和酶浓度的反应级数分别为1级和1.2级;得到了与传统的Michaelis-Menten动力学机制不同的非均相酶促反应动力学模型,确定了“表观”活化能与酶浓度之间的定量关系.     

富镧稀土镍储氢合金催化甲苯液相加氢反应的动力学研究

研究了由富镧稀土镍储氢合金与甲苯组成浆液储氢体系 ,储氢合金催化甲苯液相加氢反应的动力学特性。考察了反应温度、液相氢浓度等因素对浆液体系内部传质 反应过程的影响。结果表明 ,在实验条件下富镧稀土镍 甲苯浆液体系中甲苯的液相加氢反应速率随反应温度的升高而升高 ,并在 4 90K左右达到最大 ,当温度超过 5 10K后反应速率迅速下降。富镧稀土镍 甲苯浆液体系中甲苯的液相加氢反应为反应控制过程 ,体系中气 液界面和液相主体到催化剂表面的传质阻力完全可以忽略。表现反应速率对甲苯表现为零级 ,对液相氢浓度为一级 ,得到反应动力学模型 ,该模型与实验结果有很好的一致性 ,富镧稀土镍催化的甲苯加氢反应的活化能为 4 1 0 1kJ·mol- 1。     

离子交换树脂吸附乙酰丙酸的动力学研究

研究了大孔弱碱性树脂D310对乙酰丙酸的静态吸附动力学特征.采用批式离子交换法,考察了树脂粒径、溶液浓度、搅拌速率、温度对交换过程的影响,并用动边界模型对乙酰丙酸的离子交换过程进行了描述..结果表明,离子交换过程的控制步骤为颗粒扩散控制,搅拌速率和反应温度对交换速率无显著影响,吸附速率随乙酰丙酸初始浓度的增加而升高.交换过程的反应速率常数k0为0.8315,反应级数n为0.5313,表观活化能Ea为9.504kJ/mol,并得到了动力学总方程式.     

金属离子在液相氧化中的催化作用——Ⅱ.在乙苯液相氧化中几种铈络合物的催化作用

研究了几种配位体(环烷酸盐、硬脂酸盐、乙酰丙酮盐)对铈离子催化作用的影响。动力学结果表明,三种催化剂的反应级数几乎是相同的;表观活化能分别为15.2、17.0、10.2仟卡/克分子;对乙苯的反应级致为1。实验结果指出,反应的诱导期与催化剂、催化剂浓度、反应物浓度和反应温度有关。发现铈离子在诱导期结束后才发生价态变化,诱导期倒数与温度倒致成直线关系,由此求得的活化能与由阿累尼斯方程求得的相同。实验结果支持了络合-链锁机理。     

CO_2气氛下生物焦气化反应动力学参数的实验研究:I.活化能

利用热重分析仪在750!1 000℃对四种生物质进行了CO2等温气化实验。结果表明,各生物质焦的气化反应性随气化温度的升高而增加。用碳转化率为20%时的瞬时气化反应速率r0.2对反应速率r进行无量纲化,发现在实验温度范围内,各焦炭的无量纲气化反应速率-碳转化率曲线均存在两种变化趋势。利用等转化率法求取了四种生物焦在碳转化率达到20%后的气化反应活化能,发现同一种焦炭的气化反应活化能受碳转化率的影响较小,而不同种类焦炭的活化能主要受到焦中无机矿物成分的影响。各焦炭的活化能与焦中碱金属含量与固定碳含量的比值WC/WFC存在近似的线性关系:E=233.9-1 005.7×(WC/WFC)。若忽略催化效应的影响,焦炭本征气化反应的活化能趋于某一定值,约为234 kJ/mol。     

La-CoMoN_x/CNTs催化剂上氨分解反应的本征动力学

以La-CoMoNx/CNTs为催化剂,对氨分解制氢反应的本征动力学进行了研究。考察了N2浓度、H2浓度、NH3浓度以及反应温度对反应速率的影响。采用幂指数方程描述反应动力学,确定了本征动力学参数,推导出了本征动力学方程,得到反应的活化能为93.948 kJ/mol。同时对其反应机理进行了探讨,认为La-CoMoNx/CNTs催化剂上氨分解反应遵循Temkin-Pyzhev机理,即表面氮原子的结合脱附为反应的速率控制步骤。     

在十六烷基三甲基溴化铵(CTAB)溶液中水杨酸酯水解反应动力学 研究

应用UV-vis法,在不同温度条件下,对水杨酸酯(丁酯、苯酯)在CTAB溶液中的水解反应进行跟踪,测定了不同浓度的表面活性剂存在下的反应速率常数,得出CTAB对其反应是禁阻作用。通过温度对其反应速率影响,计算它们的反应活化能。并用^1HNMR方法,确定了反应物在CTAB胶束中的增溶位置,对禁阻的机理进行了探讨。     

新型引发剂引发苯乙烯聚合的动力学

采用过氧化2-乙基己基碳酸叔丁酯为引发剂,研究了苯乙烯自由基本体聚合的动力学过程,考察了引发剂浓度、温度、乙苯质量分数对聚合反应速率和聚苯乙烯分子量的影响.结果表明:在117℃下,聚合速率(Rp)对引发剂浓度的反应级数为0.42,对苯乙烯浓度的反应级数为1,聚合反应的表观活化能为54.8 kJ/mol.引发剂浓度、温度、乙苯质量分数的提高导致聚苯乙烯数均分子量分别下降了约30％、20％和15％,其中引发剂浓度的影响最为显著.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.