芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

N-甲基丙烯酰-N′-甲基哌嗪在嵌段聚醚氨酯膜上的Co~(60)-γ辐射接枝的研究

<正> 用亲水性单体对嵌段聚醚氨酯(SPEU)膜接枝共聚以改善其抗凝血性能,在医用材料的研究中已引起普遍重视,但由于一般化学方法接枝引发系统中带入的小分子常常对产品的医用性质造成不利的影响。我们曾报道通过Co~(60)-γ射线预辐照法用亲水性单体对以PTMG;MDI与不同的二胺类扩链剂制备的SPEU膜接枝共聚。本文在此基础上选用了两种单体AMP和MAMP。     

聚β-羟基丁酸酯辐照接枝顺丁烯二酸酐及产物表征

探索了一种提高聚β羟基丁酸酯(PHB)热稳定性的方法,即用60Coγ射线辐照对PHB进行顺丁烯二酸酐(MAH)的接枝,采用1HNMR、13CNMR、TGA、DSC、XRD等方法对辐照接枝产物进行了表征.1HNMR、13CNMR谱图结果表明MAH单体接枝到了PHB上.TGA测试表明,辐照接枝产物的热稳定性显著提高,如接枝率为0.52%的样品热分解温度提高了36K.DSC研究表明辐照接枝产物的熔融温度和结晶温度均降低.此外,由于引入极性单体顺丁烯二酸酐,接枝产物的结晶度降低,同时亲水性提高.     

乙烯-乙烯醇共聚物的固体核磁共振研究

乙烯 (Ｅ) /乙烯醇 (Ｖ)共聚物 (ＥＶＯＨ)为结晶性高聚物 ,作为膜材料有着广泛的用途 .在该体系中 ,不仅存在复杂的化学和物理结构 ,如序列分布、立构规整性和共晶结构 ,还存在复杂的氢键相互作用 ,是研究化学结构、聚集态结构和氢键相互作用之间关系的代表性体系 .通过ＤＳＣ[1 ] 、Ｘ 射线衍射[2 ] 、固体高分辨核磁共振碳谱 (1 3Ｃ ＣＰ/ＭＡＳ ＮＭＲ) [3～ 7] 等不同的研究方法 ,前人对ＥＶＯＨ体系及与之直接相关的乙烯醇均聚物(ＰＶＡ)的熔融温度、结晶度以及结晶结构等问题进行了大量研究 .1 984年Ｔｅｒａｏ等[6] 首先报道了在固…     

电火花引发HEMA 接枝LDPE 薄膜及其血液相容性

采用接枝量、ATR－IR、SEM、与水接触角、溶血试验和再钙化时间等测试手段研究了电火花引发甲基丙烯酸β－羟乙酯(HEMA)表面接枝低密度聚乙烯(LAPE)薄膜的接枝聚合反应影响因素、表面结构和血液相容性。结果表明,电火花能有效引发HEMA在LDMA薄膜表面接枝聚合反应,随接枝聚合反应时间延长、单体浓度的增大。接枝量增大。随反应温度升高,接枝量增大到一最大值后,进一步升高反应温度,接枝量下降,最佳接枝聚合温度为60℃当在60℃单体φ=5％水溶液是反应2h时,经空气气氛和1.5kV电火花预处理72s和LDPE薄膜表面接枝量可达169ug/cm^2。接枝改性后LDPE薄膜与水的接触下降,亲水性增加,溶血程度减小,再钙化时间延长,血液相容性得到改善。     

电火花引发HEMA 接枝LDPE 薄膜及其血液相容性

采用接枝量、ATR－IR、SEM、与水接触角、溶血试验和再钙化时间等测试手段研究了电火花引发甲基丙烯酸β－羟乙酯(HEMA)表面接枝低密度聚乙烯(LAPE)薄膜的接枝聚合反应影响因素、表面结构和血液相容性。结果表明,电火花能有效引发HEMA在LDMA薄膜表面接枝聚合反应,随接枝聚合反应时间延长、单体浓度的增大。接枝量增大。随反应温度升高,接枝量增大到一最大值后,进一步升高反应温度,接枝量下降,最佳接枝聚合温度为60℃当在60℃单体φ=5％水溶液是反应2h时,经空气气氛和1.5kV电火花预处理72s和LDPE薄膜表面接枝量可达169ug/cm^2。接枝改性后LDPE薄膜与水的接触下降,亲水性增加,溶血程度减小,再钙化时间延长,血液相容性得到改善。     

预辐射接枝四氟乙烯-乙烯共聚物湿敏膜的制备及特性研究

利用2 MeV电子加速器, 在常温下采用预辐照引发接枝的方法, 在四氟乙烯-乙烯共聚物(ETFE)上接枝丙烯酸(AA)和对苯乙烯磺酸钠(SSS), 制备了一种含羧酸基团和磺酸基团的接枝膜. 傅里叶变换红外光谱(FTIR)分析结果证明了磺酸基团和羧酸基团的成功引入, 并对接枝膜的热力学和化学特性进行了研究. 结果表明, 随着接枝率的增加, 接枝膜的结晶度逐渐降低, 接触角逐渐减小, 接枝膜的亲水性逐渐增强. 利用制备的接枝膜构建了电阻型湿度传感器, 并测定了传感器的电学特性. 在相对湿度(RH)从5%变化到98%时, 传感器电阻线性变化范围接近4个数量级, 具有响应速度快(吸附<1 min, 解吸<2 min), 湿滞小(<2%RH)的特点.     

1-烯丙基-3-甲基咪唑离子液体单体与丙烯腈共聚行为的研究

以1-烯丙基-3-甲基咪唑盐酸盐([AMIM]Cl)作为离子液体单体,偶氮二异丁腈作为引发剂,二甲基亚砜为溶剂,实现了与丙烯腈(AN)在不同反应条件下的自由基共聚合.研究了AN/[AMIM]Cl二元共聚合的动力学,得到了相应的竞聚率数据(rAN=8.11,r[AMIM]Cl=0).用1H-NMR、GPC、DSC、TGA等手段对共聚物进行了表征.通过对AN/[AMIM]Cl二元共聚及AN/IA/[AMIM]Cl三元共聚的研究发现,[AMIM]Cl在与丙烯腈共聚时具有双重作用,一部分离子单体进入到共聚物的分子链中调节其亲水性及可纺性,剩下的大部分留在纺丝液中可显著降低纺丝液的黏度,从而使高分子量高固含量纺丝液的纺制成为可能,有望得到高性能的碳纤维原丝.     

Mn^3＋引发淀粉与丙烯腈接枝共聚物的研究

用过渡金属离子或其配合物引发淀粉的接枝共聚是一个饶有兴趣的课题。Ce~(4 )离子引发淀粉与烯类单体的接枝共聚已有广泛报道。Mehrotra等用稳定的[Mn(H_2P_2O_7)_3]~(3-)引发淀粉与烯类单体的接枝共聚取得了满意的结果。本文报道用电镜,x-射线衍射和热重分析等方法对这一接枝共聚物的形态、结构和热稳定性的研究结果。     

丙烯酸甲酯在炭黑表面的接枝聚合及水解

在炭黑表面接枝聚合物 ,可提高其在相应介质中的分散性[1] .乙酰丙酮合锰可以有效地引发羊毛、纤维素、淀粉等天然高分子的接枝聚合 [2～ 4 ] ,季君晖 [5]将其与羟甲基化炭黑组成引发体系 ,引发了甲基丙烯酸甲酯、丙烯酸丁酯、苯乙烯等单体在炭黑表面进行接枝聚合 .但该体系难以引发水溶性的单体 ,因此得到的接枝炭黑只能用于油性体系 .目前制备亲水性接枝炭黑大多采用 Ce4 +/羟甲基化炭黑引发体系 ,该体系对 O2 特别敏感 ,反应条件相当苛刻 .本文采用乙酰丙酮合锰与羟甲基化炭黑组成引发体系 ,引发丙烯酸甲酯在炭黑表面的接枝聚合 .在 Na…     

聚氯乙烯-丙烯酸丁酯接枝共聚物的结构表征

以通用聚氯乙烯(PVC)和脱氯化氢PVC树脂为基体,采用悬浮溶胀接枝共聚法合成聚氯乙烯-丙烯酸丁酯接枝共聚物,对脱氯化氢PVC和接枝共聚物的结构进行了表征.结果表明,以碱液为介质加热PVC能脱除少量氯化氢,得到以链节数为2,3,4的共轭双键为主的不饱和结构,而树脂的分子量变化不大;在相同接枝反应条件下,采用脱氯化氢PVC与丙烯酸丁酯接枝共聚可以提高接枝率和接枝效率;PVC接枝共聚物的特性粘度随接枝率增加而增加,其重均分子量和分子量分布指数均大于接枝所用的PVC树脂.     

Synthesis and gas permeation properties of poly(vinyl chloride)‐graft‐poly(vinyl pyrrolidone) membranes

A series of amphiphilic graft copolymers consisting of poly(vinyl chloride) (PVC) main chains and poly(vinyl pyrrolidone) (PVP) side chains, i.e. PVC‐g‐PVP, was synthesized via atom transfer radical polymerization (ATRP), as confirmed by ¹H NMR, FT‐IR spectroscopy, and gel permeation chromatography (GPC). Transmission electron microscope (TEM) and small angle X‐ray scattering (SAXS) analysis revealed the microphase‐separated structure of PVC‐g‐PVP and the domain spacing increased from 21.4 to 23.9 nm with increasing grafting degree. All the membranes exhibited completely amorphous structure and high Young's modulus and tensile strength, as revealed by wide angle X‐ray scattering (WAXS) and universal testing machine (UTM). Permeation experimental results using a CO₂/N₂ (50/50) mixture indicated that as an amount of PVP in a copolymer increased, CO₂ permeability increased without the sacrifice of selectivity. For example, the CO₂ permeability of PVC‐g‐PVP with 36 wt% of PVP at 35°C was about four times higher than that of the pristine PVC membrane. This improvement resulted from the increase of diffusivity due to the disruption of chain packing in PVC by the grafting of PVP, as confirmed by WAXS analysis. Copyright © 2011 John Wiley & Sons, Ltd.     

N，N－二乙基二硫代氨基甲酸聚氯乙烯酯引发甲基丙烯酸甲酯的光接枝交联聚合反应

用铜试剂（Ｎ，Ｎ－二乙基二硫代氨基甲酸钠）取代聚氯乙烯中的部分氯原子制备了Ｎ，Ｎ－二乙基二硫代氨基甲酸聚氯乙烯酯（ＰＶＣ－ＳＲ），研究了紫外光照下ＰＶＣ－ＳＲ引发甲基丙烯酸甲酯（ＭＭＡ）的聚合反应，考察了光照时间、单体浓度、ＰＶＣ－ＳＲ用量及官能度的影响．结果表明，ＰＶＣ－ＳＲ能有效地引发ＭＭＡ聚合，其产物是交联型接枝聚合物，且具有高接枝率和接枝效率。     

Hydrogels based on physiologically clotted fibrin–gelatin composites

Fibrin–gelatin composite (PFG) films were prepared and crosslinked with glutaraldehyde as reported by us previously. These composites were graft‐copolymerized with poly(2‐hydroxyethyl methacrylate) (PHEMA) and poly(2‐hydroxypropyl methacrylate) (PHPMA) with a potassium persulfate and sodium metabisulfite redox initiation system. The graft copolymers (PFG‐HEMA and PFG‐HPMA) were characterized for their percentage of grafting, percentage of equilibrium water content, and percentages of free water and bound water. The chemical composition and thermal, mechanical, morphological, and surface characteristics were also evaluated. The optimum conditions for obtaining a maximum percentage of grafting were standardized. PFG and its graft copolymers exhibited higher equilibrium water contents ranging from 60 to 77% when compared with those of HEMA and HPMA homopolymers. DSC studies revealed increased freezing water contents and decreased bound‐water contents for the graft copolymers when compared with those of PFG alone. These properties improved the efficacy of hydrogels. PFG demonstrated better mechanical properties as compared with its graft copolymers. This may be attributed to the alkaline reaction conditions wherein protein hydrolysis of PFG would have occurred thereby reducing the overall strength of the graft copolymers. IR and scanning electron microscopic studies confirmed the grafting of PHEMA and PHPMA onto PFG. Contact‐angle studies revealed increased polarity for graft copolymers, which is a symbol for increased hydrophilicity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2241–2252, 2004     

双螺杆冻胶纺丝法制备有机液体吸附功能纤维及其性能研究

在聚合釜中合成了BMA/HEMA二元共聚树脂,利用双螺杆纺丝机、采用冻胶纺丝技术制备了有机液体吸附功能纤维,研究了单体投料比中HEMA质量分数对纤维各种溶胀行为的影响,利用动态热机械分析仪(DMA)对纤维的动态力学性能进行了研究,同时利用环境扫描电子显微镜(SEM)观察了纤维的表面和断面形貌.结果表明,HEMA引入大分子后,所得纤维对有机液体甲苯、三氯乙烯具有吸附功能,且吸附过程符合sigmoidal模型中的Hill方程;随HEMA质量分数的增加,纤维对甲苯和三氯乙烯的饱和吸附量增大,对甲苯和三氯乙烯的最大吸附量分别可达10g/g和21g/g;随HEMA质量分数的增加,纤维剩余率增加的同时,使纤维对甲苯和三氯乙烯的握持能力增强;HEMA质量分数对纤维动态力学性能有突出影响,特别是链段运动受其影响更为明显;HEMA质量分数对纤维表面和断面形貌均有显著影响,特别是当HEMA质量分数为15wt%时,所得纤维表面出现了许多空洞,其断面存在许多尺寸不均的空洞.     

Radiation-Induced Grafting of Ethyl Vinyl Ether onto Polyvinyl Chloride)

The radiation-induced graft polymerization of ethyl vinyl ether (EVE) onto polyvinyl chloride) (PVC) was studied under a variety of conditions. Graft copolymer and homopoly(EVE) were formed in all cases. The presence of water reduced overall polymerization rates, percentage grafting, and homopoly(EVE) molecular weights. With “superdry” EVE, grafting reached 29% at a total dose of 6.9 Mrad. Grafting to PVC films was less efficient than grafting to PVC powder. Application of a relatively poor swelling agent for PVC resulted in an increase in the efficiency of grafting. From a comparison of studies of radiation-induced EVE homopolymerization and the present work, it was concluded that dry and superdry EVE are grafted to PVC by a cationic mechanism and wet EVE is grafted mainly by a free-radical mechanism.     

聚乙烯—丙烯酸与聚（2—乙基—2—恶唑啉）接枝共聚物的合成及表征

选用聚乙烯－丙烯酸（ＥＡＡ）为接枝母体,首先摸索出２－乙基－２－恶唑啉阳离子开环聚合的规律,得到高转化率端基为活性翁离子的聚（２－乙基－２－恶唑啉）（ＰＥＯＸ）,再与ＥＡＡ羟基侧基进行接枝反应,考察了开环聚合条件及接枝反应条件对接枝率的影响,在一定的条件下得到了接枝率〉２５％的聚乙烯－丙烯酸与聚（２－乙基－２－恶唑啉）的接枝共聚物（ＥＡＡ－ｇ－ＰＥＯＸ）。该接枝物用于聚对苯二甲酸丁醇酯／聚丙烯（Ｐ     

Antibacterial behaviour of quaternized poly(vinyl chloride)-g-poly(4-vinyl pyridine) graft copolymers

Amphiphilic graft copolymers consisting of poly(vinyl chloride)(PVC) main chains and poly(4-vinyl pyridine)(P4VP) side chains were synthesized via atom transfer radical polymerization(ATRP) using direct initiation of chlorine atoms. The successful synthesis of PVC-g-P4 VP graft copolymers was confirmed by Fourier transform infrared spectroscopy(FTIR) and proton nuclear magnetic resonance(1H-NMR). Transmission electron microscope(TEM) and small angle X-ray scattering(SAXS) analysis showed that PVC-g-P4 VP exhibited microphase-separated, ordered structure with 37.6 nm of domain spacing, which was not observed in neat PVC. For antibacterial applications, the tertiary nitrogen atoms of PVC-gP4 VP was quaternized using 1-bromohexane, as confirmed by FTIR measurements. Bacteria including Escherichia coli(E. coli), Staphylococcus aureus(S. aureus), Bacillus cereus(B. cereus), and Pseudomonas aeruginosa(P. aeruginosa) were completely killed in 24 h on the quaternized PVC-g-P4VP(46% grafting) surface, indicating its excellent antibacterial behavior while it showed to be cytotoxic to mammalian cell.     

聚乙烯丙烯酸与聚(2-乙基-2-噁唑啉)接枝共聚物的合成及表征

选用聚乙烯 丙烯酸 (EAA)为接枝母体 ,首先摸索出 2 乙基 2 唑啉阳离子开环聚合的规律 ,得到高转化率端基为活性离子的聚 ( 2 乙基 2 唑啉 ) (PEOX) ,再与EAA羟基侧基进行接枝反应 ,考察了开环聚合条件及接枝反应条件对接枝率的影响 ,在一定的条件下得到了接枝率 >2 5%的聚乙烯 丙烯酸与聚 ( 2 乙基 2 唑啉 )的接枝共聚物 (EAA g PEOX) .该接枝物用于聚对苯二甲酸丁二醇酯 /聚丙烯 (PBT/PP)共混体系中作相容剂 ,可提高两者的相容性 .     

Graft copolymerization of 2-hydroxyethyl methacrylate and methyl methacrylate onto hide powder

Graft copolymerization of 2-hydroxyethyl methacrylate(HEMA) and mixtures of HEMA with methyl methacrylate (MMA) onto hide powder was attempted using ceric ammonium nitrate as initiator, with a view to optimize the conditions for graft copolymerization. Percent grafting and grafting efficiency were calculated for various variables such as monomer concentration, initator concentration and mole ratio of HEMA to MMA. R_p, R_g and R_h (rates of polymerization, grafting and homopolymerization respectively) were also evaluated. It was observed that R_p increased linearly with increasing concentration of MMA except at very low concentrations of the monomer. An explanation is given for the effect of variables on extent of grafting and grafting efficiency.