基于浸取pH依赖性的离子吸附型稀土分类及高效浸取方法

研究了稀土及主要杂质离子被硫酸铵浸出的pH依赖性。结果证明稀土和钙镁等离子的浸取率在低酸度范围内随酸度增大有明显提高,继续提高酸度并不会进一步提高浸取率,而铝、铁、钪等易水解金属离子的浸取率随酸度增大而持续增加。据此,基于离子吸附型稀土的定义及浸取所需pH值的范围,将离子吸附型稀土进一步区分为易浸稀土和难浸稀土,其中难浸稀土是需要在弱酸性条件(pH≤4)下才能浸取的被胶体等强吸附剂吸附的稀土离子。由于在不同地区和不同矿层及不同粒级的样品中所含强吸附剂的量以及磨蚀pH(pHd)和交换pH(pHt)的不同,这两类离子吸附型稀土的比例不同。对于pHd和pHt值较高的矿样,适当提高浸取酸度可以显著提高稀土浸取率。为此,提出了分阶段浸取稀土并增加石灰水护尾工序来保证稀土浸取率和尾矿安全稳定性的原则流程。     

Co(Ⅱ)和Ni(Ⅱ)在北山花岗岩上的吸附：表面配位模型及线性自由能关系

用批式法研究了Co(Ⅱ)和Ni(Ⅱ)在北山花岗岩(BS03, 600 m)上的吸附. Co(Ⅱ)和Ni(Ⅱ)在北山花岗岩上的吸附分配比(K_d)均随pH值、离子强度和吸附质浓度的变化而变化; 在低pH值范围, Co(Ⅱ)和Ni(Ⅱ)的K_d 值随离子强度的增大显著减小, 而在高pH值范围,离子强度对K_d的影响较小; Co(Ⅱ)和Ni(Ⅱ)在北山花岗岩上的吸附作用可以分别用1个离子交换反应和2个内层表面配位反应进行定量描述. 建立了表面配位反应平衡常数(K)与过渡金属二价离子水解常数(^OHK)之间的线性自由能关系(LFER),据此对Pb(Ⅱ)和Cu(Ⅱ)在花岗岩上的吸附进行了预测,并与实验结果进行了对比,获得了较好的一致性.     

风化壳淋积型稀土矿多级逆流浸取实验研究

风化壳淋积型稀土矿的开采主要通过浸矿剂离子与吸附在黏土矿物表面的稀土离子发生离子交换浸出反应实现。以(NH₄)₂SO₄为浸矿剂,采用多级逆流浸取的方式研究了风化壳淋积型稀土矿的浸矿过程,通过在逐级浸取过程中浸出液组分的变化分析了矿土中稀土离子(RE³⁺)和主要杂质铝离子(Al³⁺)的浸出行为,并基于浸矿剂的消耗规律探讨了浸矿剂离子与RE³⁺和Al³⁺的离子交换反应机制以及原矿土的净吸附量。结果表明,在浸矿液逐级浸取新鲜矿土的过程中,浸出液中的RE³⁺和Al³⁺浓度逐渐增加,铵根离子(NH₄⁺)逐渐消耗,交换进入浸出液中的RE³⁺和Al³⁺逐级减少;同时,浸出液中的硫酸根离子(SO₄^2-)逐级损耗,说明新鲜矿土除因发生离子交换反应消耗NH₄<...     

离子吸附型稀土浸矿机制研究现状

离子吸附型稀土是世界、尤其是中国的宝贵资源。为实现该类稀土资源的绿色高效开采,人们对离子吸附型稀土的浸取机制进行了系统而深入的研究,为确定其成矿机制和提取工艺做出了突出贡献。1969～1989年,基于离子型稀土的浸取特征,证明了各种电解质溶液均可浸出稀土,并用简单的离子交换反应和水化理论来说明稀土离子的浸取规律和能力大小,为浸矿剂的选择和提取工艺的提出做出了重大贡献;从1989～2009年,研究重点转移到稀土的吸附、解吸和动力学迁移机制等方面,着力解决堆浸和原地浸矿中的基础问题;从2009～2019年,进一步用双电层理论来重新说明稀土离子浸出的机制,着力于解决环保问题并进一步提高浸取效率,为发展新的浸取体系和工艺指明了方向;本文按照上述三个主要阶段的具体研究成果和贡献进行述评,重点对第三阶段的新进展开展讨论,在此基础上,对离子吸附型稀土浸矿机制的研究方向与趋势进行了展望。     

亚氨二乙酸型复合材料IDAA-PGMA/SiO2对重金属及稀土离子的吸附行为与吸附热力学

将甲基丙烯酸缩水甘油酯(GMA)接枝于硅胶微粒表面,制得了接枝微粒PGMA/SiO₂; 使亚氨二乙酸(IDAA)与接枝PGMA的环氧基团发生开环反应, 从而将亚氨二乙酸基团引入接枝微粒表面, 制得了复合螯合微粒材料IDAA-PGMA/SiO₂. 本文研究了IDAA-PGMA/SiO₂对重金属及稀土离子的螯合吸附行为, 深入地研究了吸附机理与吸附热力学. 研究结果表明: 凭借亚氨二乙酸基团与重金属离子之间的静电作用与配位螯合作用的协同, 复合微粒材料IDAA-PGMA/SiO₂对重金属离子可产生强的螯合吸附作用, 尤其对Pb²⁺离子表现出很强的螯合吸附能力, 常温下吸附容量可达0.235 g·g^-1; IDAA-PGMA/SiO₂对重金属离子的吸附过程为一放热过程, 且为焓驱动的过程, 升高温度, 吸附容量降低; 对稀土离子的吸附过程则为熵驱动的过程; 在可抑制金属离子水解的pH范围内, 介质的pH值越高, IDAA-PGMA/SiO₂的螯合吸附能力越强; IDAA-PGMA/SiO₂对重金属离子的吸附容量远高于对稀土离子的吸附容量.     

阴-非离子表面活性剂复合改性水滑石的表面性质研究

采用十二烷基苯磺酸钠（SDBS）、吐温-80（Tween-80）及两种表面活性剂复合改性镁铝水滑石,得到SDBS-LDHs,Tween-LDHs及SDBS/Tween-LDHs₃种改性水滑石。利用反相气相色谱法（IGC）对样品进行表面性质的研究,定量计算了表面吸附自由能（ΔG₀）和表面能色散组分（γ_s^d）。结果表明,改性材料的ΔG₀与γ_s^d值均比未处理的镁铝水滑石小,其中阴-非离子表面活性剂复合改性后的水滑石的ΔG₀与γ_s^d值最小,说明阴-非离子表面活性剂复合改性水滑石较单一改性水滑石更有利于提高材料的稳定性。此外,各类水滑石的γ_s^d值均随着温度的升高而减小,因此,在制备聚合物/水滑石类材料时,可以利用提高温度来改善其与聚合物的相容性。     

离子吸附型稀土浸取试剂和富集回收技术的演变——从抑杂浸取到强化浸取及分阶段的选择-强化浸取

硫酸铵浸取离子吸附型稀土，碳酸氢铵沉淀法富集回收工艺在工业上已经使用了30多年。其突出优点是浸取效率高，沉淀富集产品质量好，生产成本低。然而，其对环境的影响只有在确保浸出液不外泄，水和溶液都能循环利用的前提下才能得到控制。近10年来，人们着力于研发用非铵试剂来浸矿，以解决氨氮超标问题。尽管在降低氨氮污染方面取得了很好成绩，但是，在以往甚至当前的原地浸矿方式下，收液率很难超过90%，环保问题无法根本解决。本文基于当前该领域与浸取剂，沉淀剂和萃取剂及稀土浸取富集相关的研究成果，客观地分析了各种试剂和方法的优缺点，讨论了浸取策略从抑杂浸取到强化浸取以及分阶段的选择-强化浸取的变迁，这种变迁需要后续富集回收技术的支撑作用以提高效率和产品质量、降低消耗和成本。而试剂本身存在的一些不足可以通过它们之间的相互耦合和后续富集回收流程的优化来克服。据此，对当前存在的问题和未来发展趋势提出了一些基本观点。     

磁性Fe3O4@SiO2@ZrO2对水中磷酸盐的吸附研究

合成了以Fe₃O₄为核,以SiO₂为壳的磁性纳米微粒（Fe₃O₄@SiO₂）,并采用沉淀沉积法将ZrO₂包覆到材料表面。通过XRD、TEM、XPS和N₂吸附/脱附等手段对材料进行表征,结果表明材料Fe₃O₄@SiO₂@ZrO₂上沉积了氧化锆纳米颗粒,具有超顺磁性,可在外加磁场作用下实现从水中快速分离。同时系统研究了材料对水中磷酸盐的吸附行为,结果表明沉积ZrO₂使得材料对磷酸盐表现出良好的吸附性能,并且随着沉积量的增大吸附量增加。吸附等温线可用Freundlich方程拟合。吸附动力学可用拟二级动力学模型拟合,吸附速率随初始浓度增加而减缓。磷酸盐吸附量随溶液pH值的增大而减小,但几乎不受离子强度影响。     

赣南信丰风化壳淋积型稀土矿的吸附特性

风化壳淋积型稀土矿体吸附特性对于提高原地浸矿稀土浸取率具有重要意义。通过筛分获得不同粒径的风化壳淋积型稀土矿样,测试各粒径矿样的离子相稀土品位、比表面积、表面形貌以及矿物成分等,分析稀土离子在矿体中的吸附特性。研究结果表明:赣南信丰类型的稀土矿体中矿物成分有高岭石、钾长石、石英、电气石、白云母等,这5种主要矿物成分的总质量比重达到90.13%,不同矿物成分的粒度有明显的差异,小粒径矿样中高岭石和白云母的含量增加,矿样的稀土离子吸附量与高岭石等黏土矿物的含量成正相关;基于稀土离子在矿体颗粒表面凹坑的单位面积吸附量与孔径和粒径成对数正态分布,建立了稀土离子吸附量与矿体颗粒表面凹坑孔径之间关系的分析模型,运用该模型计算得到赣南信丰类型的有效吸附孔径为2.0~20.0 nm。     

混合稀土对A2B7型储氢合金结构和电化学性能的影响

采用感应熔炼方法制备了A₂B₇型La_0.83-0.5x（Pr_0.1Nd_0.1Sm_0.1Gd_0.2）_xMg_0.17Ni_3.1Co_0.3Al_0.1（x=0~1.66）储氢合金,并在He+Ar气氛和 1 173 K下进行退火处理。通过X射线衍射（XRD）、扫描电子显微镜（SEM）和电化学方法,研究了混合稀土（Pr,Nd,Sm,Gd）替代La元素对合金物相结构和电化学性能的影响。合金相结构分析表明,混合稀土含量对合金组成和相结构有重要的影响,随混合稀土含量x的增加,合金中主相A₂B₇型（2H-Ce₂Ni₇型+3R-Gd₂Co₇型）相丰度逐渐增多,其中2H-Ce₂Ni₇型相丰度先增多后减少,3R-Gd₂Co₇型相丰度则逐渐增加,主相晶胞参数随x增加而减小。电化学结果表明,随混合稀土含量增加,放氢平台压逐渐升高,合金电极的最大放电容量和循环稳定性均呈先增大后减小的规律,其中x=0.4合金电极具有最高的电化学放电容量（389.8 mAh·g^-1）和最佳的循环寿命（S₁₀₀=91.30%）;合金电极的高倍率放电性能（HRD）则随x的增加获得显著提高。适量的混合稀土替代量可显著改善合金电极的综合电化学性能。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.