在RuO2|Pd|YSZ|PddeNOx电解池中O2-传导的速控步骤

研究了500～750℃富氧条件下RuO₂|M|YSZ|Pd(M=Ag,Pd,Pt,Au)固体电解质电解池在0～4V直流电压下对NO的分解性质.600℃下,O^2-在Pd|YSZ阴极界面处的传导是O^2-在RuO₂|Pd|YSZ|Pd固体电解质电解池中传导过程的速控步骤.反应温度越低,RuO₂|Pd|YSZ|Pd电解池上NO电催化分解相对于氧分解的选择性因子α越大.600℃下O^2-在M|YSZ阴极界面处的传导阻力按Ag2|Ag|YSZ|Pd电解池上分解率为15.3%,NO选择性因子达到13.4.     

O_2存在下NO在固体电解质电池上分解机理

研究了在O_2存在条件下,NO在Pd |YSZ| Pd固体电解质电池和RuO_2 |Pd|YSZ| Pd固体电解质电池上的分解性质,在O_2存在条件下650 ～ 700 ℃之间 ,在0 ～ 4.4 V直流电压作用下,NO在Pd |YSZ| Pd电池和RuO_2|Pd|YSZ| Pd电池 上的分解不以电解机制进行,而以电催化机理进行的。即在直流电压下,阴极催化 剂上的O~(2-)被直流电压通过YSZ固体电解质转移到阳极,以O_2的形式放出,以此 保持催化剂的活性状态。在Pd|YSZ|Pd 固体电解质电池上,Pd金属表面是催化NO分 解的主要活性位。RuO_2 |Pd|YSZ| Pd固体电解质电池上,某特定还原态的RuO_x (0 < x < 2)是NO分解的主要活性位。在O_2存在下,该电池在1 ～ 4 V间合适的电 压下,在650 ～ 700 ℃能选择性地对NO进行电催化分解。     

氢部分选择性催化还原NO反应研究

在低钯含量活性非均布Pd/Al2O3催化剂上，实现了富氧条件下，氢部分选择性催化还原NO过程，低温、富氧条件下NO的转化率高达80％－100％。NO直接分解实验表明，600℃，NO分解转化率在无氧时为17．3％，有0．5％氧存在时接近于0。氢非选择性还原NO条件下，100℃以下，NO转化率为100％。根据实验结果及文献，推测了氢部分选择性还原NO过程中可能存在的反应，不同的反应温度下，NO脱除反应有所不同。在115℃以下，NO还原产物为NH3；115℃－155℃，NO还原产物为NH3、N2O和N2；155℃以上，NO还原产物中无NH3存在。NO还原反应与氢氧反应是平行的竞争反应。     

Ti-HMS介孔分子筛的制备及其在一氧化氮催化分解反应中的活性

 在常温下制备了具有不同钛含量的大比表面积和孔体积的介孔分子筛HMS．XRD谱表明,这些Ti－HMS样品呈现出很好的六方晶形．经焙烧后,Ti－HMS样品的UV吸收光谱和XAFS谱结果表明,在Ti－HMS（1）和Ti－HMS（2）骨架中的钛离子以四配位存在,而在Ti－HMS（10）中至少有部分钛是以六配位存在．在NO存在的情况下,在273K下光催化剂Ti－HMS受紫外光照射后,导致NO分解生成N2,O2和N2O．实验结果表明,具有高分散四配位钛的Ti－HMS（1）使NO以高效率、高选择性分解生成N2和O2;随着钛含量的增加,其光催化活性反而降低．     

尖晶石对β／β″—Al2O3膜相组成和离子导电性的影响

以wag／P”－AI。O。为固体电解质的CO。、SO。、NO。等气体传感器的研究已有很多报道［‘－‘］，多采用的是个AI。O。结构的电解质。AI刀。和p”－AI刃。的结构具有一定的相似性，但后者具有更高的迁移离子浓度和更开放的晶体结构，表现出更好的离子导电性‘’‘．由于卢”－AI。O。为介稳结构，需要加入如Li。O、MgO等作为稳定剂才能稳定存在．以Li对稳定的产”－al。O。烧结较容易，P”－AI。O。相转化率高，但以MsO为稳定剂制备的”－AI刃。其显微结构和抗吸湿性能更为优越．LJLi对和MgO共同稳定的产”－AI。O。可以…     

用TPD研究SO2对NO催化氧化过程的影响

 针对活性氧化铝载体及过渡金属氧化物催化剂上SO2增强NO吸附并促进其氧化的实验事实，考察了反应温度对SO2发挥促进作用的影响．结果发现，在50～250℃间存在一适宜的温度范围，能使氧化铝上原本不氧化的NO在SO2气氛中发生氧化．对氧化铝预吸附不同组成的气体及在不同温度下吸附NO－O2－SO2后进行了TPD研究．结果表明，SO2的存在对NO氧化吸附生成NO2高温脱附物种有利．对Co3O4／Al2O3催化剂上吸附SO2－NO2的TPD研究结果显示，SO2先吸附或与NO2共吸附都能使NO2高温物种脱附增强，同时SO2的弱吸附物种转变成强吸附物种或表面硫酸盐物种，意味着弱吸附的SO2能与NO2形成稳定的物种；而后吸附的SO2竞争占据NO2的吸附位．推测表面上弱吸附的SO2与NO－O2或NO2之间形成了多分子的活性物种．     

用CuO／γ－Al2O3催化剂同时脱除烟气中的SO2和NO

 研究了用CuO／γ－Al2O3催化剂同时脱除烟气中的SO2和NO，并在固定床反应器中考察了反应条件对其催化活性的影响．结果表明，温度和SO2对CuO／γ－Al2O3的催化活性均具有双重影响．新鲜催化剂和硫化催化剂上最适宜的脱硝温度分别为250～300℃和300～450℃，最适宜的n（NH3）／n（NO）约为1．2．烟气中的氧可大大提高CuO／γ－Al2O3的脱硫脱硝活性．综合考虑吸附硫容和NO脱除率，CuO／γ－Al2O3同时脱硫脱硝的最适宜温度为350～450℃．温度和SO2在高温区对CuO／γ－Al2O3活性的影响源于两者对NH3氧化活性的改变，高温下CuO／γ－Al2O3的活性下降是因为NH3氧化加剧；SO2通过使催化剂硫化生成硫酸盐来抑制NH3氧化，从而提高CuO／γ－Al2O3的活性．吸硫饱和的催化剂可于5％NH3中还原再生，再生后其硫容较初始时降低，但其活性大幅度提高．     

一元硝酸酯热解反应的理论研究

运用SCF－AM1－MO方法，计算研究了十个一元硝酸酯的热解反应，揭示了烷基取代对反应过程的影响．UHF计算O－NO2键均裂产生RCH2O·和·NO2两个自由基的反应活化能较低，是硝酸酯热解的主要途径;RHF计算α-H转移环消除产生RCHO和HONO的反应具有较高活化能，且α-C上含两个以上取代基时不发生该反应．还探索性地进行了C－O键断裂的UHF和RHF计算．.     

镓掺杂SO2－4／ZrO2的制备及其对正丁烷异构化反应的催化性能

 通过沉淀、回流和浸渍法制备了镓掺杂的纳米级固体超强酸SO2－4／Ga2O3／ZrO2，并用X射线衍射、透射电镜、热重、吡啶吸附红外光谱、低温N2－BET及化学分析等技术对SO2－4／Ga2O3／ZrO2的结构、表面性质及其对正丁烷异构化反应的催化活性进行了研究．结果表明，掺杂Ga2O3可以抑制制备过程中ZrO2晶粒长大，有利于抑制高温下催化剂由四方相转变为单斜相．与未掺杂的催化剂相比，Ga2O3的掺杂提高了催化剂表面SO2－4的分解温度，有利于催化剂表面形成更多的酸中心．SO2－4／Ga2O3／ZrO2对正丁烷异构化反应显示出优异的催化性能．其中，含3％Ga2O3的样品的活性最高，220℃下其初活性为59．1％；反应1h后，其活性基本保持稳定，稳态转化率大于51％，接近该反应条件下正丁烷的平衡转化率．     

高性能镓酸镧基电解质燃料电池

制备并用多种电化学方法研究了LaGaO3基高性能中温固体氧化物燃料电池的电极和电解质材料，组装出了高性能单电池.实验发现， Co掺杂的La0.8Sr0.2Ga0.8Mg0.2O3电解质中， Co含量的增加显著提高了电解质的氧离子电导率，电解质的氧迁移数略有减小，是非常好的中、低温燃料电池电解质.钴掺杂的电解质不仅显著减小了电池的欧姆电阻，而且减小了电池的阴、阳极极化过电位.以La0.8Sr0.2Ga0.8Mg0.11Co0.09O3为电解质时电池在1073、973、873 K下的最大输出功率密度分别达到1.77、0.92、0.41 W•cm－2，是非常有前景的电池体系.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.