化妆品中阴阳离子的快速测定及其用于化妆品鉴别的研究

用离子色谱电导检测器对黑泥类化妆品中的阴、阳离子(Na+,NH+4,K+,Mg 2+ ,Ca 2+ ,Cl-,Br-,NO-2,NO-3和SO 2- 4)进行了测定。阳离子分离条件: 阳离子交换柱ICS C25,均苯四甲酸淋洗液浓度2.0 mmol/L ,流速0.6 mL/min ;阴离子分离条件: 阴离子交换柱Shim pack IC A1,淋洗液为2.5 mmol/L 邻苯二甲酸和2.4 mmol/L 三羟基氨基甲烷,流速1.0 mL/min 。结果表明,上述10种离子在较宽浓度范围内有良好     

高效阴离子交换色谱-脉冲安培法测定生态养护抑菌凝胶中的褐藻寡糖

建立高效阴离子交换色谱–脉冲安培检测法测定生态养护抑菌凝胶中褐藻寡糖含量的方法。采用阴离子交换柱Carbo Pac PA10(250 mm×2 mm,3.5μm),以氢氧化钠、乙酸钠和水为洗脱液进行梯度洗脱,柱温为35℃,流量为0.8 mL/min。α-L-古罗糖醛酸单糖(PG)和β-D-甘露糖醛酸单糖(PM)的质量浓度分别在0.25～9.0μg/m L和0.18～8.4μg/mL范围内与色谱峰面积线性关系良好,线性相关系数分别为0.999 7和0.999 8,检出限分别为0.06,0.03μg/m L,定量限分别为0.20,0.10μg/mL。测定结果的相对标准偏差分别为1.11%,1.25%(n=6),加标回收率分别为101.03%和95.22%。该方法简便易行,灵敏度高,重现性好,适用于生态养护抑菌凝胶中褐藻寡糖的分析。     

直接电导检测-离子色谱法分离测定氟硼酸根及常见无机阴离子

研究了直接电导检测-离子色谱法分离测定BF4-及常见无机阴离子(F-、Cl-、Br-、NO3-、SO24-)。实验采用Shim-pack IC-A3阴离子交换色谱柱,分别选用邻苯二甲酸氢钾、对羟基苯甲酸 三(羟甲基)氨基甲烷 硼酸、邻苯二甲酸 三(羟甲基)氨基甲烷为淋洗液,考察了淋洗液种类、浓度、色谱柱温度、流速对分离测定BF4-及常见无机阴离子的影响。确定最佳色谱条件为:以1.25 mmol/L邻苯二甲酸氢钾为淋洗液,流速1.5 mL/min,柱温45℃。在此条件下可同时基线分离6种阴离子,且色谱峰形对称。所测阴离子的检出限为0.02~0.58 mg/L;峰面积的相对标准偏差(RSD,n=5)小于0.8%。将方法应用于测定离子液体中的BF4-及其它无机阴离子,加标回收率在98.2%~102.7%之间。     

大体积进样离子色谱法测定环境水样中高氯酸根

采用大体积500μL进样离子色谱法,电导检测测定了几种水体中高氯酸盐的含量。分析柱为容量高、亲水性强的以脂肪族碳骨架为基质的阴离子交换柱IonPac AS20,淋洗液在线发生器自动产生35 mmol/LKOH淋洗液,0.25 mL/m in等浓度淋洗。这种新型的以脂肪族碳骨架为基质的阴离子交换柱的采用,极大的削弱了该色谱柱对对氯苯磺酸的保留,完全消除了现行美国EPA高氯酸盐分析方法中高氯酸根与对氯苯磺酸共淋洗的问题。方法对高氯酸根的检出限(S/N=3)为0.5μg/L,高氯酸根浓度在1~1000μg/L范围内具有良好的线性(r=0.9991)。将本方法应用于自来水、河水和雪水样品中高氯酸盐的检测,实际样品的加标回收率在87%~114%之间;1μg/L高氯酸根连续进样9次,色谱峰面积相对标准偏差(RSD)为6.9%。     

高效阴离子交换色谱-脉冲安培检测法测定烤烟中的水溶性葡萄糖、果糖和蔗糖

用高效阴离子交换色谱-脉冲安培检测法（HPAEC-PAD）测定了烤烟中的水溶性葡萄糖、果糖和蔗糖。采用水浸取及膜过滤法处理烤烟样品,以Dionex CarboPac PA-1阴离子交换柱为色谱柱,0.2 mol/L NaOH水溶液为淋洗液进行分离测定。葡萄糖、果糖和蔗糖的含量与其峰面积的线性关系良好,回收率均在97%以上。方法简便易行,灵敏度高,重现性良好,可以实现对烟草中单糖的快速分离和测定。     

抑制电导离子色谱法测定蔬菜、药品和水中对氨基苯磺酸

建立抑制电导离子色谱法测定蔬菜、药品和水中对氨基苯磺酸.以SH–AC–3型阴离子交换柱为分离柱,5.0 mmol/L Na2CO3–1.5 mmol/L NaHCO3为淋洗液,以1.0 mL/min的流量等度洗脱,对氨基苯磺酸与常见阴离子可实现完全分离,对氨基苯磺酸的色谱峰面积与质量浓度在0.05～100.0 mg/L...     

离子色谱法测定浴盐中的阴、阳离子

用离子色谱法测定浴盐中的Na^ 、K^ 、Mg^2 、Ca^2 、Cl^-、Br^-、SO4^2-时，分离阳离子的色谱柱为ICS-C25阳离子交换柱，淋洗液为2.0mmol/L均苯四甲酸溶液，流速为0.6mL/min；分离阴离子时的色谱柱为shim-pack IC-Al阴离子交换柱，淋洗液为2.5mmol/L邻苯二甲酸溶液－2.4mmol/L三羟基氨基甲烷溶液（体积比为1：1），流速为1.0mL/min。所测离子Na^ 、K^ 、Mg^2 、Ca^2 、Cl^-、Br^-、SO4^2-在较宽浓度范围内有良好的线性关系，回收率为94.7%-102.4%，检出限为0.001-0.02mg/L，相对标准偏差为1.03%-1.63%。     

整体柱离子相互作用色谱快速分析无机阴离子

研究了用硅胶整体柱和直接电导检测的离子相互作用色谱快速分析常见无机阴离子的方法。实验采用氢氧化四丁铵和邻苯二甲酸为淋洗液,讨论了包括淋洗液浓度、流速和pH对分离的影响。当以1.5 mmol/L氢氧化四丁铵和1.1 mmol/L邻苯二甲酸为淋洗液(pH 5.5),流速6 mL/min时,可以在1 min内分离Cl-、NO2-、Br-、NO3-、ClO3-、SO42-和I-7种阴离子。方法的检出限为0.3~1.9 mg/L,峰面积、峰高的相对标准偏差(RSD,n=5)分别为0.4%~2.2%和0.1%~1.5%。将该法用于测定矿泉水和地下水中的阴离子,加标回收率在97.9%~100.3%之间。     

固相萃取-阴离子交换色谱法测定硝酸异辛酯合成后残留的混酸含量

建立了一种固相萃取-阴离子交换色谱-抑制型电导检测的分析方法,同时测定合成硝酸异辛酯(柴油十六烷值改进剂)反应后残留的混酸(硝酸和硫酸)的含量。样品经过Bond Elut C18OH固相萃取小柱萃取净化后,以1.0m L/min的流速,经Shim-pack IC-SA2阴离子交换分析柱(4.0 mm i.d×250mm,9μm)分离,淋洗液为1.8 mmol/L Na2CO3-1.7 mmol/L Na HCO3混合液,进行等度洗脱,并用外标法进行定量分析。硝酸和硫酸分别在0.3~9 mg/L和12~120 mg/L范围内呈良好的线性关系,相关系数分别为0.999和0.996;加标回收率分别为90.0%~101.43%和94.25%~102.4%,检出限为0.01 mg/L和0.05 mg/L,相对标准偏差RSD(n=6)小于3.0%。     

大体积进样-离子色谱法测定炉水中痕量阴离子

提出了大体积进样-离子色谱法测定火电厂炉水中8种阴离子F-、CH3COO-、HCOO-、Cl-、NO2-、NO3-、SO42-及PO43-的含量。水样经AG17-C保护柱及AS17-C分离柱分离,以氢氧化钾溶液为淋洗液进行梯度淋洗,采用抑制电导器检测。8种阴离子的质量浓度均在5.0～50μg·L-1范围内与峰面积呈线性关系,检出限(2S/N)在0.01～0.11μg·L-1之间,测定下限(10S/N)在0.05～0.52μg·L-1之间。方法用于火电厂炉水中8种阴离子的测定,加标回收率在97.8%～107%之间。     

Flow-injection technique for the determination of low levels of phosphorus in natural waters

An inexpensive flow-injection instrument for determining low concentrations of dissolved reactive phosphorus in natural waters is reported. The unique feature is the use of an inexpensive detector consisting of a flow cell and a simple photometer that incorporates a super-bright light-emitting diode as the source and a photodiode as the detector. The tin(II) chloride-molybdate method was optimized using a modified simplex optimization method. Silicate interference up to 5 mg Si l^?1 was removed by addition of 0.10% (w/v) tartaric acid. Using the tartaric acid-modified optimized reagents, a detection limit of 0.6 μg P l^?1 was achieved. The method was linear over the range 0–100 μg P l^?1 with an excellent precision (r.s.d. 2.9% at 2.0 and 0.5% at 50 μg P l^?1). An in-line pre-concentration anion-exchange column was used to obtain an even lower detection limit of 0.1 μg P l^?1 and applied to the analysis of real samples.     

Sensitive spectrofluorimetric determination of zinc at ultra-trace levels

An ultra-trace method based on the reaction of zinc with salicylthiocarbohydrazone (SATCH) and Triton X-100 as a non-ionic surfactant was developed for the fluorimetric determination of zinc at the picogram level. The reaction is carried out in the pH range 4.4–4.7 in an aqueous ethanolic medium [52% (v/v) ethanol]. The influence of the reaction variables is discussed. The detection limit is 10 pg ml^?1 and the range of application is 0.01–500 μg l^?1, with an optimum range of 0.04–400 μg l^?1. The relative standard deviations are 0.68% (0.01–0.1 μg l^?1 of zinc), 0.41% (0.1–1.0 μg l^?1 of zinc), 0.64% (1–10 μg l^?1 of zinc), 0.82% (10–100 μg l^?1 of zinc) and 0.15% (100–500 μg l^?1 of zinc). The method is highly sensitive and selective in the presence of Cd^II and Hg^II. The effect of interferences from other metal ions and anions was studied; the masking action is discussed. The advantages of the proposed method include its high sensitivity, simplicity and selectivity.     

Atomic-absorption determination of vanadium and molybdenum in tap water and mineral waters after anion-exchange separation.

A method is described for the determination of vanadium and molybdenum in samples of tap and bottled mineral water. After acidification with citric acid the water sample is heated to about 80°C to remove CO₂; sodium citrate and ascorbic acid are added and the resulting solution of pH 3 is passed through a column of the strongly basic anion-exchange resin Dowex 1-X8 (citrate form) on which both vanadium and molybdenum are adsorbed as anionic citrate complexes. Vanadium is eluted with 6 M hydrochloric acid; molybdenum is recovered with 2 M perchloric acid-1 M hydrochloric acid. Vanadium and molybdenum are determined in the eluates by atomic-absorption spectrometry. The samples analysed contained 0.1–0.9 μg l^?1 vanadium and 0.2–13 μg l^?1 molybdenum.     

Speciation and analysis of corrosion products in the primary coolant of pressurized water reactors

The procedure involves separate sampling and determination of the insoluble, cationic and anionic species of corrosion products (Fe, Ni, Cr, Mn, Co, Zn, Cu) in the primary coolant of pressurized water reactors (PWRs) with concentrations in the range 0–2000 mg l^?1 boron and 0–5 mg l^?1 lithium. Samples of coolant (0.2–1 l) are passed through packs consisting of one 0.45-μm filter paper, one cation-exchange membrane (Whatman SA-2) and one anion-exchange membrane (Whatman SB-2). The membranes are examined by wavelength-dispersive x-ray spectrometry. Selection of the ion-exchange membranes and the influence of the boron and lithium concentrations (and pH) on retention of soluble species are discussed. With sample volumes of 0.5 l, the detection limits are between 0.05 and 0.3 μg l^?1 for undissolved species and from 0.03 to 0.14 μg l^?1 for ions. Data collected during a PWR shutdown procedure are summarized.     

Sensitive determination of traces of boron in waters,fertilizers na geological and biological materials by isotope-dilution mass spectrometry

A method is described for determining traces of boron in water, fertilizers, geological and biological (reference) materials by isotope-dilution mass spectrometry after separation on an Amberlite IRA-743 borate-selective ion-exchange column. Boron (–250 ng g^?1) in water can be determined with an accuracy of 5–20% (computed on a 2s basis). After correction for weighing errors and for moisture, content, which varied from 0 to 8% for the samples tested, 1–35 μg g^?1 boron in “dry” fertilizer, biological or geological sample can be assayed with an accuracy of 5–30% (2s). In an IAEA interlaboratory program on a simulated fresh water, the method yielded a value of 24.3 +? 2 μg l^?1, compared to the make-up value of 25 μg l^?1.     

Monosaccharide composition analysis of immunomodulatory polysaccharides by on‐line hollow fiber microextraction with high‐performance liquid chromatography

The monosaccharide compositions of functional polysaccharides are essential for structure elucidation and biological activity determination. A sensitive method based on on‐line hollow‐fiber liquid‐phase microextraction with high‐performance liquid chromatography has been established for the analysis of ten monosaccharide compositions (two uronic acids, two amino sugars and six neutral sugars) of the immunomodulatory polysaccharides. After derivatization , the sample was injected into the lumen of a hollow fiber immersed in butyl ether and separated by liquid chromatography. Under optimized conditions, the calibration curves were linear (r ≥ 0.9996) in the range of 10–2000 μmol L^?1. The limits of detection were in the range of 0.04–1.58 μmol L^?1, and the recoveries were in the range of 92.1–99.6%, which shows that the method is applicable to the analysis of the monosaccharide composition of various polysaccharides.     

Peroxidase-catalysed rupture of the CF bond as and indicator reaction for enzyme immunoassay : Kinetic determination of human immunoglobulin G, α-fetoprotein and placental lactogen

A fluoride ion-selective electrode is utilized as a sensor for the kinetic determination of peroxidase label in enzyme immunoassays. The method is based on a sandwich enzyme-linked immunosorbent assay (ELISA) technique, the peroxidase-catalysed rupture of the covalent CF bond in 4-fluorophenol and the subsequent release of fluoride ions. The determination of human immunoglobulin G (lgG), human α-fetoprotein (AFP) and human placental lactogen (HPL) was investigated. The potentiometric measurement of the rate of release of fluoride ion within 5 min provided a direct correlation with the concentration of analyte present in the sample. The concentration ranges investigated for the analytes were IgG 30 μg l^?1–10mg l^?1, AFP 5–500 μg l^?1 and HPL 60 ng l^?1–1 mg l^?1. Under the given experimental conditions, the detection limits were IgG 30, AFP 12.8 and HPL 1 μg l^?1. Replacing the rate method with the fixed-time mode (15–30 min) did not improve the detection limits. The performance of the present method was found to be comparable to that of the spectrophotometric detection technique.     

Examination of the lignin content in a softwood and a hardwood decayed by a brown‐rot fungus with the acetyl bromide method and Fourier transform infrared spectroscopy

Fourier transform infrared (FTIR) spectroscopy was used to examine lignin modification in Pinus sylvestris L. (Scots pine) and Fagus sylvatica L. (beech) decayed to different weight losses by the brown‐rot fungus Coniophora puteana. Samples of different weight losses, ranging from 3 to 64% for beech and 15 to 62% for pine, were analyzed along with undecayed controls. The ratios of the heights of the lignin/carbohydrate FTIR peaks were determined, and the lignin contents of the blocks were measured with the acetyl bromide method. The ratios of the reference peaks for lignin against polysaccharide (i.e., cellulose and hemicellulose) peaks were compared with the lignin content of the wood determined by the acetyl bromide method. A good correlation was obtained for ratios of some of the lignin/carbohydrate reference peaks (lignin peaks at 1505 and 1330 cm^?1 for beech and at 1511 and 1225 cm^?1 for pine against polysaccharide peaks at 1734, 1375, and 1158 cm^?1) against the lignin content for both wood species decayed to different levels. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2340–2346, 2004     

Determination of selenium in human body fluids by hydride-generation atomic absorption spectrometry : Optimization of sample decomposition

The accuracy of the determination of selenium in human body fluids by hydride-generation a.a.s. depends critically upon the sample decomposition-method used. Digestion with HNO₃ alone gave low selenium recoveries, but with nitric, sulfuric and perchloric acids at a final temperature of 310°C gave results that agreed with those obtained by other techniques. The recovery of selenomethionine added to whole blood and of trimethylselenonium iodide added to urine was 97–104%. The average selenium values found for 6 healthy individuals were 88 μg l^?1 in whole blood, 75 μg l^?1 in blood plasma and 307 μg (kg Hb)^?1 in erythrocytes. A detection limit of 5 μg l^?1 Se in body fluids was found under routine conditions.     

The simultaneous determination of As,Cd, Co,Hg, Mo,and Zn in fresh water by neutron activation analysis

A radiochemical neutron activation method for the simultaneous determination of arsenic, cadmium, cobalt, mercury, molybdenum, and zinc in fresh water is described. The method is based on anion-exchange separation in hydrochloric acid media followed by simple precipitations. The determination limits, based on analysis of a 5-ml sample without preconcentration, and with a well-type NaI(Tl) detector, are as follows: As, 10^-3 μg l^-1 ; Cd, 6 × 10^-2 μg l^-1 ; Co, 4 × 10^-3 μg l^-1 ; Hg, 7 × 10^-3 μg l^-1 ; Mo, 10^-1 μg l^-1 ; Zn, 2 × 10^-1 μg l^-1. The method is adequate for the analysis of natural fresh waters.