POSS基杂化含氟丙烯酸酯共聚物涂膜的表面相分离与疏水性研究王鹏金云皮丕辉文秀芳徐守萍程江

采用自由基溶液聚合法成功合成了多面体低聚倍半硅氧烷(POSS)基杂化含氟丙烯酸酯共聚物,并采用核磁共振仪(NMR)和凝胶渗透色谱仪(GPC)表征了共聚物,其中POSS和含氟单体分步加入到反应中.首先将共聚物溶解到三氟三氯乙烷(F113)和乙酸乙酯的混合溶剂中配制成溶液,然后通过直接在玻璃片上滴落共聚物溶液制备了共聚物涂膜.采用扫描电子显微镜(SEM)、X-射线光电子能谱(XPS)、原子力显微镜(AFM)和接触角测量仪考察了F113和乙酸乙酯的配比对共聚物涂膜表面形貌、表面元素组成、表面粗糙度以及表面疏水性的影响.实验数据表明POSS在表面能够聚集成纳米颗粒并能极大增强涂膜表面粗糙度和疏水性.共聚物表面同时存在POSS聚集与有机相微相分离两类相分离行为,并形成了复合粗糙结构.虽然POSS和含氟段竞争迁移到表面,但是随着混合溶剂中F113的增多,涂膜表面含氟量越来越多,同时POSS在表面的聚集体越来越少,表面平均粗糙度越来越小,最终涂膜的疏水性越来越强,这说明F113有助于提升氟的趋表迁移能力,使涂膜表面含氟链段占据较多的表面空间,从而抑制了POSS在表面聚集分布.当使用纯F113作为溶剂时,共聚物涂膜的表面氟含量为45.25%,平均粗糙度为93.4 nm,此时静态水接触角最大为135.0?,表现出优异的疏水性.     

含氟硅丙烯酸酯乳液超疏水膜中疏水基团的梯度分布与表面微观结构研究

利用含氟疏水基团的梯度分布,结合草莓形纳米SiO2粒子提供的双重粗糙表面,制备了具有类"荷叶效应"的超疏水涂膜,水接触角达(174.2±2)°,滞后角几乎接近0°.通过原子力显微镜、扫描电镜和水接触角的测试对膜表面形貌及疏水性能进行了表征;探讨了其表面微观结构与表面疏水性能的关系.草莓形复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度,使水滴与涂膜表面接触时能够形成高的空气捕捉率,这种微观结构与疏水基团的梯度分布相结合,赋予了含氟硅丙烯酸酯乳液涂膜表面超疏水性能.     

优化含氟丙烯酸酯共聚物乳胶膜表面性能的方法研究

含氟丙烯酸酯乳液由于氟的引入具有优异的表面性能,在涂料、胶粘剂、纺织助剂等领域得到广泛应用.然而含氟单体成本较高,而且产物中乳化剂的存在影响了含氟丙烯酸酯乳液涂膜的抗污、疏水疏油等特性.如何采取有效措施提高含氟丙烯酸酯共聚物乳胶膜的表面性能,是其走向产业化急需解决的问题.针对这方面问题,本文主要从含氟单体的利用率、设计乳胶粒结构、共聚物链结构以及乳胶膜的后处理等方面对近年来的研究成果进行了综述.     

含长氟链丙烯酸酯共聚物的合成及应用展望

采用传统自由基共聚合方法合成了新型的含氟大分子单体PFMA-MA,并将其与甲基丙烯酸甲酯(MMA)、丙烯酸异丁酯(IBA)和γ-甲基丙烯酰氧基丙基三甲氧基硅烷(MPTS)进行自由基共聚合成了长氟链丙烯酸酯共聚物(ACLC)。对该聚合物的表面性能以及本体性能进行了研究。结果表明,少量的PFMA-MA便可使得到的共聚物ACLC的憎水性大幅度提高。通过X射线光电子能谱(XPS)研究大幅提高憎水性的机理,结果表明ACLC中的长氟链段具有强烈的迁移特性,氟原子富集于表面,使得材料憎水性得到提高。ACLC具有优异的附着力、硬度和低吸水率。含长氟侧链梳形丙烯酸酯共聚物有望应用在疏水、防水涂层材料等领域。     

复合SiO2粒子涂膜表面结构及超疏水性能

采用溶胶-凝胶法制备不同粒径SiO₂粒子，通过表面改性得到不同形状复合粒子，并利用氟硅氧烷的表面自组装功能制备了具有“荷叶效应”的超疏水涂膜。通过原子力显微镜、扫描电镜和水接触角的测试对膜结构及性能进行了表征，探讨了SiO₂粒子的粒径和形状与表面微观结构、表面粗糙度和表面疏水性能的关系。结果表明含单一粒径粒子涂膜表面水接触角符合Wenzel模型，而复合粒子构成了符合Cassie模型的非均相界面;单纯的粗糙度因子不能反映水接触角的变化，复合粒子在膜表面的无规则排列赋予涂膜表面不同等级的粗糙度，使得水滴与涂膜表面接触时能够形成高的空气捕捉率和较小的粗糙度因子;其与在涂膜表面能形成自组装分子膜的氟硅氧烷共同作用赋予了涂膜超疏水性能，而这种超疏水性能与复合粒子的粒径大小和形状基本无关。     

含氟丙烯酸酯共聚物表面性能的稳定化研究

为提高传统含氟丙烯酸酯乳胶膜表面性能的稳定性,以γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(MPS)作为可交联单体,采用细乳液聚合法合成了MPS改性的含氟丙烯酸酯共聚物,利用DLS、TEM、IR对聚合物进行表征,研究了MPS对合成乳液的稳定性、涂膜性能和膜表面接触角稳定性的影响。结果表明,细乳液聚合法适合用于对水敏感单体的聚合,合成的纯丙烯酸酯乳胶为球形结构,平均粒径为92 nm,而氟丙乳胶和含3%MPS的含硅氟丙乳胶形成了典型的核壳结构,平均粒径分别增大至107 nm和103 nm,含硅氟丙聚合物中存在Si-O-Si的交联结构。涂膜性能测试表明,MPS的引入增加了共聚物膜的硬度、耐溶剂性和耐水性。接触角测试表明,随MPS用量的增加,乳胶膜对水的初始接触角和动态接触角随时间的降低值均呈先增大后减小的趋势,共聚体系中加入适量MPS,通过含氟链段与MPS链段的协同作用,可显著提高涂膜表面性能的稳定性。     

含氟丙烯酸酯共聚物制备超疏水表面及其形成机理的研究

以丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯为共聚单体, 分别以用微乳液聚合法和溶液聚合法制备的无规共聚物和用可逆加成-断裂链转移制备的嵌段共聚物作为成膜共聚物, 并以1,1,2-三氟三氯乙烷作为溶剂, 采用溶剂挥发成膜法可以直接制备出超疏水膜, 聚合物膜对水的接触角可达160°. 改变聚合物结构和成膜条件, 探讨了该类超疏水膜的形成机理和影响因素. 发现膜的表面形貌和疏水性与共聚物的组成、结构、分子量以及成膜条件密切相关, 随着共聚物中氟含量的增大, 膜的表面形貌都趋于平滑; 而且, 无规共聚物比嵌段共聚物更易形成粗糙度好的膜; 同时, 较大的聚合物分子量和适宜的高的成膜温度都对形成粗糙结构有利.     

热处理对超疏水性含氟丙烯酸酯共聚物膜表面性能的影响

以微乳液聚合法和溶液聚合法制备丙烯酸全氟烷基乙基酯和甲基丙烯酸甲酯的共聚物, 以1,1,2-三氟三氯乙烷为溶剂, 采用溶剂挥发成膜法直接制备出超疏水膜, 并研究120 ℃热处理对超疏水膜表面性能的影响. 对于用乳液聚合方法制备的超疏水膜, 随着热处理时间的延长, 滚动角表现出先逐渐增大直至完全不能滚动, 然后重新回复到极小滚动角的特殊变化过程, 而静态接触角只是略微减小, 完全不同于热处理对平滑的含氟聚合物表面接触角的影响. 扫描电镜结果显示, 聚合物膜表面形貌对应出现从微/纳复合粗糙结构到微孔粗化并重新形成微/纳复合多层粗糙结构的变化.     

氟化嵌段共聚物组成、溶液性质与其固化后的表面结构

采用ATRP技术合成了不同含氟段长度的聚甲基丙烯酸甲酯一b．聚（甲基丙烯酸一2．全氟辛基乙酯）（PMMA144-b-PFMAn）嵌段共聚物．利用接触角、XPS、SFG、表面张力、DLS等技术研究了不同含氟段长度PMMA144-b-PFMAn溶液气／液界面性质、聚合物分子在溶液中的聚集行为与其固化后表面结构与性能．发现含少数几个氟化结构单元的嵌段共聚物就呈现出优异的疏水疏油性．含氟段的增长其表面性能反而下降．对其表面结构进行研究发现,含氟量的增加,使含氟组分在表面富集程度的增加有限,F／C比则随深度的增加而增加．同时全氟烷基在表面的排列有序性下降．当氟化结构单元的长度为10时,共聚物的表面层反而出现了PMMA的链段．原因主要是由于含氟段的长度影响嵌段共聚物分子在溶液中的聚集结构和气／液界面结构,从而影响固化过程中其表面结构的形成．结果表明,高含氟量的聚合物不一定具有优异的表面性能,合适的溶液性质对含氟聚合物表面结构的形成具有重要的影响．     

超疏水涂膜的研究进展

超疏水涂膜以其独特的性能，在国防、工农业生产和日常生活中有着广泛的应用前景。但目前的制备技术制约了其在建筑外墙涂料等大型设施方面的应用。探索如何采用简单有效的方法构造和调控涂膜的双微观结构，从而获得性能持久优异的超疏水性涂膜，并有效应用于生产和生活的各个方面是这一领域研究的最终目标。本文就超疏水材料表面理论的发展和近几年来超疏水膜制备技术取得的新成果进行了概括，并指出制备超疏水涂膜存在的问题和发展方向。利用表面能极低的含氟材料，将溶胶－凝胶、相分离技术和自组装梯度功能等技术有机结合，获得适宜的表面粗糙度和微观构造，是实现超疏水涂膜工业化生产的可行途径。     

Synthesis and Characterization of Novel UV-curable Fluorinated Polyurethane-acrylate Copolymer

A series of UV-curable fluorinated polyurethane-acrylate(PUA) has been developed by incorporating octafluoropentyl alcohol into the segment of UV-curable polyurethane-acrylate to improve the thermal property and surface property of the copolymer material. The structures of the synthesized polymers were characterized by Fourier transform infrared(FTIR) spectrometry. In order to find out the effect of incorporated fluorine on the UV-cured films, the properties of the UV-cured films were tested through contact angle, water absorption, and thermogravimetric analysis (TGA). The fractured-surface morphologies of the UV-cured coatings were investigated by scanning electron microscopy(SEM). With increasing the content of fluorine segments, the contact angle of the UV-cured films increased and the water absorption decreased, suggesting the fluorine segments migrated and formed a fluorine-covered surface to avoid water penetration. The observation of the fractured-surface morphology through SEM test showed that the fluorinated UV-cured films gained rough fractured-surface compared with the pure UV-cured polyacrylate film, demonstrating the migrating of the fluorine segments. The TGA curves show that the fluorinated UV-cured films gained higher thermal degradation temperature than the virgin UV-cured polyacrylate film. And as increasing the fluorine content, the thermal degradation temperature increased. These phenomena could be reasonably explained by the enrichment of fluorinecontained segment on the surface of the film and the high thermal property due to fluorine atom.     

用含氟丙烯酸酯无规共聚物制备超疏水膜

用微乳液聚合法制备了丙烯酸全氟烷基乙酯和甲基丙烯酸甲酯的无规共聚物,并对其进行了表征.采用溶剂挥发成膜法一步制备了具有超疏水性的该聚合物膜,水滴在该聚合物膜上的静态接触角可达151°~160°,滚动角小于3°.通过扫描电子显微镜观察发现该聚合物膜表面分布了许多乳突状突起和微孔洞,并具有微米和纳米尺度相结合的复合杂化结构.该类超疏水表面的形成是由适度粗糙的表面和低表面能相互结合引起的.探讨了该类超疏水膜的形成机理.     

Synthesis and characterization of a new fluorinated macroinitiator and its diblock copolymer by AGET ATRP

A new fluorinated macroinitiator of poly 2,2,3,4,4,4-hexafluorobutyl methacrylate-Br (PHFMA-Br) was prepared via activator generated by electron transfer atom transfer radical polymerization (AGET ATRP), and then a series of fluorinated block copolymers with different fluorine content were successfully synthesized from the macroinitiator by the second step AGET ATRP. GPC, FTIR and ¹H NMR data obtained verified the synthesis. Contact angle measurement indicated that proper fluorine content could decrease the surface energy and increase the contact angle of the copolymer films. XPS characterization showed that the large difference in surface energy between the block and random copolymer film resulted from the difference of the fluorine content on the surface, although the fluorine content of the two copolymers in bulk was similar. The self-assembly behavior of the fluorinated block copolymer in selective solvents was evaluated by the TEM study, and the stable micelles with a core-shell structure were observed when the copolymer content was about 1 wt%.     

氟含量对含氟丙烯酸酯共混乳胶膜梯度结构和表面性能的影响

首先将制备出的平均粒径较小的含氟丙烯酸酯均聚物乳液与平均粒径较大的纯丙烯酸酯共聚物乳液按不同的比例( 1/9,2/8,3/7,4/6,5/5)共混,接着将各共混乳液在室温下(20℃)玻璃基材上干燥后,于110℃/210℃下热处理一段时间.运用接触角法,XPS、AFM、SEM-EDX等详细研究了共混乳胶膜中含氟组分含量对...     

成膜溶剂与氟化嵌段共聚物膜的表面富集行为

利用接触角、XPS、SFG、AFM等技术研究了环己酮、甲苯和三氟甲苯为成膜溶剂所得聚甲基丙烯酸甲酯-b-聚（甲基丙烯酸-2-全氟辛基乙酯）（PMMA—b—PFMA）嵌段共聚物膜的表面结构与性能．发现浇铸成膜时成膜溶剂对聚合物氟化组分向表面富集程度的影响相对较小,而旋涂成膜时溶剂的影响很大．不管以何种形式成膜,三氟甲苯溶剂最有利于氟化组分向表面富集,甲苯次之,环己酮最差．这一现象与溶剂的挥发速度无关．聚合物在溶液中的聚集结构、气／液界面结构是造成成膜方式对聚合物表面结构与性能产生巨大影响的主要原因．当聚合物在溶液中形成以PFMA为核、PMMA为冠的胶束结构时,在溶液固化过程中氟化组分向表面富集需要较长的时间,这时由于成膜方法直接影响溶液的固化速度,造成其对氟化组分向表面富集的程度影响很大．当聚合物在溶液中以单分子或松散聚集体存在,在溶液固化过程中氟化组分向表面富集的速度很快,这时成膜方法对氟化组分向表面富集的程度影响很小．以上结果无论对理论研究还是应用研究都具有重要意义．     

B段选择性成膜溶剂对 ABC 型氟化三嵌段共聚物氟化组分表面富集行为的影响

利用ATRP技术合成聚甲基丙烯酸甲酯-b-聚甲基丙烯酸丁酯(或聚甲基丙烯酸十八烷基酯)-b-聚(甲基丙烯酸2-全氟辛基乙酯)(PMMA230-b-PBMA12(或PODMA12)-b-PFMAn)嵌段共聚物.通过X射线光电子能谱(XPS)、X射线衍射(XRD)、动态光散射(DLS)等技术研究了中间段选择性成膜溶剂对氟化...     

含氟丙烯酸酯聚合物乳胶膜表面性质

采用XPS和界面张力仪分别测定了含氟丙烯酸酯聚合物乳胶膜表面的组成及水在其表面的动态接触角, 并用状态逼近方程模型计算了含氟聚合物乳胶膜的表面张力, 考察了温度对乳胶膜润湿性的影响. 结果表明, 含氟聚合物乳胶膜表层较深处的F 1s信号强度比近表面要弱, 乳胶膜表面张力随表面氟原子浓度增加在一定程度上呈现线性下降；含氟侧链(Rf)较长(碳原子数n＞6)的含氟聚合物, 其表面张力随Rf单元含量增加而下降的趋势显著高于Rf较短(n≤6)的含氟聚合物, 而水在含氟聚合物乳胶膜表面上的后退接触角θr随n增大出现急剧上升, n≥10 时, θr值几乎恒定不再随n增大而改变. 此外, 参与共聚的非氟丙烯酸酯酯基碳链较短时, 水在共聚物乳胶膜表面的θr随氟单元含量增加而增加的趋势更显著；温度超过40 ℃后, 水对聚合物乳胶膜的润湿性随温度上升略有改善.     

The suspension�Cemulsion combined polymerization of fluorinated acrylic monomer and the fluorinated latex film surface properties

The perfluoroacrylate-containing copolymer composite particles were fabricated by suspension?Cemulsion combined polymerization (SECP). The features and formation mechanism of resulting polymer particles in SECP were studied. The fluorinated latexes with better stability and those fluorinated films with high surface fluorine content were prepared by SECP using fluorine-free surfactants as an emulsifying agent, and the surface natures of the fluorinated films were characterized. It was found that P(MMA?CBA) latex particles gradually coagulated with P(PFA?CBA) particles after adding emulsion polymerization constituents at the midstage of the suspension polymerization, and fluorinated composite particles with core?Cshell structure and larger size were obtained. The fluorine contents either on the film surface or in the bulk of the film and the films from SECP are higher than those from miniemulsion polymerization at high PFA feed ratio (more than 20?wt.%). The model of PFA?CMMA?CBA SECP was proposed according to the variations of particle features of the composite particles.     

Fluorinated modification of hyperbranched polyesters used for improving the surface property of UV curing coatings

The commercial hyperbranched aliphatic polyols (Hn) were modified by thioglycolic acid (TA) and hexafluorobutyl acrylate (HFBA) or dodecafluoroheptyl methacrylate (DFHMA) to prepare a series of fluorinated hyperbranched polyesters. For comparison, a linear fluorinated polymer, poly(n-BMA-co-DFHMA), was synthesized through the copolymerization of n-butyl methacrylate (BMA) and DFHMA. The molecular structures were characterized by ¹H NMR spectroscopic analysis. The synthesized polymers were incorporated into UV-curable formulations as additives, and exposed to a UV lamp. After UV curing, the wettability of the films was investigated by contact angle measurement with water and 1-bromonaphthalene. The results showed that both the hydrophobicity and oleophobicity were greatly enhanced. Moreover, the fluorinated hyperbranched polymers possessed better water and oil repellency than the copolymer poly(n-BMA-co-DFHMA) at a very low concentration. The surface F/C ratio values of the cured films were detected by XPS analysis, and the film with TAH20-DFHMA showed the highest F/C ratio value, indicating its most efficient aggregation effect at the film surface.     

Synthesis and properties of low‐dielectric‐constant polyimides with introduced reactive fluorine polyhedral oligomeric silsesquioxanes

A high‐performance, low‐dielectric‐constant polyimide (PI) nanocomposite from poly(amic acid) (PAA) cured with a reactive fluorine polyhedral oligomeric silsesquioxane (POSS) isomer was successfully synthesized. The features of this reactive fluorine POSS isomer [octakis(dimethylsiloxyhexafluoropropylglycidyl ether)silsesquioxane (OFG)] provided two important approaches (containing fluorine or being porous in the polymer matrix) of reducing the dielectric constant of PI. This reactive POSS isomer had an average of four epoxy groups and four fluorine groups on the POSS cage, and the epoxy groups could be cured with PAA to form a network framework of a PI/POSS nanocomposite. The PI/OFG nanocomposite had a high crosslinking density, high porosity (24.3%), high hydrophobicity, and low polarizability. These properties enhanced the thermal (glass‐transition temperature ～ 362 °C) and dielectric (dielectric constant ～2.30) properties of PI more than other POSS derivatives introduced into the PI backbone. A large number of small POSS particles (<10 nm) were embedded inside the PI matrix when the OFG content was low, whereas interconnected POSS aggregation domains were observed when the OFG content was high. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5391–5402, 2006