溶剂挥发法制备萃取剂微胶囊

萃取剂微胶囊的制备是利用微囊化方法将萃取剂包覆起来 ,解决传统液液萃取中的两相相分散、相混合、相分离以及溶剂的损失和设备结构复杂等问题 .用简单易控制的溶剂挥发法成功制备了聚砜及聚苯乙烯材料包覆的多种萃取剂 (如磷酸三丁酯 ,2 乙基己基磷酸 ,三辛胺和Aliquat 336 )微胶囊 ,并考察了壁材和分散剂的选择对不同萃取剂进行包覆的影响 ,同时研究了搅拌速度和膜溶液组成对微胶囊的形态、萃取剂包覆量的影响 .结果表明 ,(1)用聚砜作壁材可以包覆磷酸三丁酯、2 乙基己基磷酸 ,而用聚苯乙烯可以包覆三辛胺、Aliquat336 ;(2 )对于不同的O W乳液体系 ,只有选择合适的分散剂 ,才能得到理想球形状、分散性好的微胶囊 ;(3)增大搅拌速度可以降低液滴尺度 ,从而减小微胶囊粒径 ;(4)膜溶液组成的影响则表现在两个方面 ,一是膜溶液的粘度和两相界面张力是除搅拌速度外微胶囊粒径的决定因素 ,二是膜溶液中壁材与萃取剂的比例优化时 ,才能得到萃取剂包覆量高的微胶囊 .     

以聚脲为囊壁薄荷素油微胶囊的制备及表征

采用界面聚合法,以薄荷素油为芯材,以异佛尔酮二异氰酸酯为壁材单体,在催化剂四甲基乙二胺作用下和水反应形成聚脲外壳,制备出了薄荷素油微胶囊.通过扫描电镜、激光粒度分析仪、傅里叶红外光谱仪及热重分析仪分别对香精微胶囊的表面形貌、粒径分布、单体反应情况和热稳定性进行了分析表征.通过紫外可见分光光度计对香精微胶囊包覆率进行了测定.并分析了均质化速率和微胶囊平均粒径的关系以及不同乳化剂种类和芯壁比条件下微胶囊的形貌特征.结果表明,微胶囊平均粒径随均质化速率的增大而减小,下降到1μm左右时趋于平稳,当乳化剂采用聚乙烯醇且芯壁比为4∶1时,微胶囊形貌最佳,为规整球形.最终测得微胶囊芯材包覆率为84.09 wt%,粉末状微胶囊样品含油率为72.64 wt%,并且微胶囊芯材具有良好的热稳定性.     

二甲基硅油中溶剂挥发法制备微胶囊

以二甲基硅油(PDMS)作为连续相,用搅拌制乳——溶剂挥发的方法制备了聚丙烯腈(PAN)、醋酸纤维素(CA)、壳聚糖(CTS)等几种聚合物包覆Aliquat336(ALQ)、四甘醇(TEG)和牛血清白蛋白(BSA)等分离剂的微胶囊.其中挥发溶剂是N,N-二甲基甲酰胺(DMF),乙酸(AA)和水等极性溶剂.整个制备过程不需要添加任何其他表面活性剂,就可以得到分散性和球形度都很好的微胶囊,相比一般的溶剂挥发过程影响因素少,易于调控.制备得到的微胶囊表面致密,平均粒径在10～100μm之间.通过增加连续相粘度和降低聚合物溶液浓度的方法都可以使微胶囊粒径更小.在PDMS中添加一定量待包覆的萃取剂就可以实现对微胶囊包覆率的调控,实验中ALQ/PAN,TEG/CA和BSA/CTS微胶囊的包覆率分别可以达到0·43,0·38和0·08g/g.     

改性胺微胶囊固化剂制备工艺的优化与性能

以改性胺1618固化剂为囊芯、脲醛树脂为壁材单体,采用界面聚合技术,成功制备了一种新型聚脲改性胺微胶囊固化剂。通过正交设计试验,考察了芯壁质量比、乳化剂种类和质量分数及搅拌速率对微胶囊包覆率、粒径大小及分布情况的影响,并确定了最佳制备工艺条件。采用马尔文激光粒度仪、扫描电镜对微胶囊粒径大小、分布情况及表面形貌进行表征,采用热重分析仪及傅里叶变换红外光谱对其化学结构进行表征,通过拉伸试验对自修复材料的断裂力学性能进行研究。结果表明,该微胶囊含有固化剂芯材,其热稳定温度为198°C,当芯壁质量比为0.7∶1、乳化剂为阿拉伯胶、乳化剂质量分数为1.5%、搅拌速率为800r/min时,所制备的微胶囊包覆率达到79.8%,平均粒径为207.5nm,呈规则的球形,分散性及表面致密性好。当基体材料中加入质量分数为1%的微胶囊后,拉伸强度提高64%,弹性模量提高287%。     

单层膜包裹的金纳米粒子的表面状态对铁氰根离子和硫代硫酸根离子间的氧化还原反应的影响

利用三维自组装膜包覆的金纳米粒子为电子转移媒介体, 研究电子在三维自组装膜表面的转移行为. 文中以3-巯基丙酸和11-巯基十一酸包覆的金纳米粒子为催化剂, 催化铁氰化钾与硫代硫酸钠之间的反应. 该催化反应的机理为金纳米粒子作为电子转移的媒介体, 电子在金纳米粒子表面转移的速度决定着反应的速度. 因此, 电子在这种三维自组装膜上的转移速度和反应速度成正比, 而该反应的反应速度可以由铁氰化钾的紫外光谱的变化得到. 实验中得到的表观电子转移速度比理论计算隧道电流产生的电子转移速度的最大值小几个数量级, 这可能是由于纳米粒子能级不连续性造成的.     

基于聚苯胺微胶囊的双重自修复防腐涂层

将乳液模板法、光聚合法以及苯胺的界面聚合相结合制备了负载亚麻籽油的聚苯胺微胶囊,并将微胶囊与水性环氧树脂涂层相结合来构筑了具有优异光热转化能力的双重自修复防腐涂层.当涂层受损后,微胶囊中的自修复剂亚麻籽油释放出来,对涂层进行修复;在近红外光(NIR)的照射下,聚苯胺可以有效地吸收光能并将其转化为热能,使涂层的温度高于其玻璃化转变温度,涂层破损处实现愈合.聚苯胺微胶囊的加入不仅赋予涂层优异的自修复能力,而且大大增强了其防腐能力.涂层的表面形貌、电化学与盐雾测试结果表明,聚苯胺微胶囊添加量为10%的涂层在NIR照射3 s内,可以实现快速闭合,恢复了其阻隔性能.此外,在300 h的盐雾测试后,涂层未产生任何的腐蚀产物,而纯涂层可以明显看到腐蚀现象.这种双重自修复防腐涂层的超快响应时间和高愈合效率以及优异的防腐性能具有潜在的应用价值.     

甲胺基阿维菌素苯甲酸盐微胶囊的制备与表征

以三聚氰胺-甲醛树脂为壁材,采用原位聚合法制备了甲胺基阿维菌素苯甲酸盐微胶囊,研究了三聚氰胺与甲醛的质量比、芯壁比、乳化剂、搅拌速度与时间、pH值、温度等因素对微胶囊形成的影响,对制备的微胶囊进行了表征,测定了甲维盐微胶囊化前后的光解率。结果表明,三聚氰胺与甲醛质量比为1∶2、芯材与壁材质量比为3∶2、以质量分数1%羟乙基纤维素(HEC)为乳化剂、在1000r/min搅拌速度下、pH=5.0和50℃保温2h可制备出形貌较好、平均粒径4.4μm的甲维盐微胶囊。红外光谱分析证明,甲维盐已完全被包覆在微胶囊中。紫外分光光度法测定其缓释性能良好。光解实验表明,微胶囊化可有效降低甲维盐原药的光解。     

大豆分离蛋白-十二烷基硫酸钠微胶囊的制备与表征

以大豆分离蛋白(SPI)和十二烷基硫酸钠(SDS)为壁材, 以十六烷为芯材, 通过复凝聚法制备了微胶囊. 首先确定了SPI和SDS发生复凝聚的适宜pH、SPI/SDS配比、壁材浓度等. 在确定的实验条件下进行复凝聚, 凝聚物产率可达85%. 改变搅拌转速和芯壁比, 考察它们对微胶囊性能的影响. 用光学显微镜观察了微胶囊形貌. 用气相色谱测定了微胶囊的载药量和包覆率. 芯壁比为2、搅拌转速为400 r/min时所制备微胶囊的载药量可达61%. 随着芯壁比的增大, 微胶囊粒径及载药量都逐渐增大.     

基于脲醛原位聚合制备聚硫密封剂微胶囊

设计了以脲醛树脂为壁材,聚硫橡胶密封剂为囊芯的微胶囊.在弱酸性条件下,尿素和甲醛在经乳化分散后的聚硫橡胶密封剂微粒表面发生原位聚合,制备了颗粒均匀、形貌规整、分散性好的密封剂微胶囊.通过红外光谱和表面观察技术对微胶囊进行了表征,并且对微胶囊中密封剂含量进行测定.通过对不同物料和反应影响因素(乳化剂浓度、搅拌速度、反应温度和p H值等)进行了系统考察,获得了优化的微胶囊制备工艺条件.为进一步拓展聚硫橡胶密封剂预涂敷技术和工程化应用提供了有益参考.     

对苯乙烯磺酸钠改性炭黑对天然橡胶胶乳力学性能的影响

在Haake转矩流变仪的热机械作用下,用对苯乙烯磺酸钠(NASS)对炭黑进行预处理,制备了在水介质中具有优异的分散稳定性的亲水性纳米炭黑粒子(PNASS-CB),并将其直接用于天然橡胶胶乳的补强研究.1HNMR和FT-IR结果表明NASS在炭黑表面成功聚合包覆,用热重分析方法计算其包覆率为8.1 wt%,接枝率为2.5 wt%.亲水性炭黑的表面自由能降低,同时,Payne效应和结合胶含量表明亲水性炭黑粒子与橡胶的相互作用强于亲水性炭黑粒子之间的相互作用.因此,亲水性炭黑/天然橡胶胶乳复合材料的硫化时间变短,转化速度加快,硫化胶的撕裂强度提高了85%,拉伸强度提高了30%,断裂伸长率提高了20%.     

Waterborne polyurethane-coated polyamide/fullerene composite films: Mechanical,thermal, and flammability properties

Novel waterborne polyurethane (WPU) was prepared and coated on nylon 12 (Ny12) and fullerene-C60 (Full-C60, 1–10 wt%) composite films using simple dip coating technique. In Ny12/Full-C60 composite, fullerene nanoparticles were dispersed in a wavy layered pattern, whereas coated WPU/Ny12/Full-C60 films depicted uniform pattern of non-overlapping scales. WPU/Ny12/Full-C60 1–10 showed higher values of tensile strength and modulus, 91.4–98.1 MPa and 52.2–57.9 GPa, respectively. In WPU/Ny12/Full-C60 1–10, maximum degradation temperature was increased to 598°C and char yield to 35%. Increasing fullerene content from 1 to 10 wt% decreased maximum peak heat release rate from 209 to 132 kW m^?2, i.e., 53% reduction in flammability compared to WPU.     

Preparation and characterization of controlled heparin release waterborne polyurethane coating systems

In this study, to improve hemocompatibility of biomedical materials, a waterborne polyurethane (WPU)/heparin release coating system (WPU/heparin) is fabricated via simply blending biodegradable WPU emulsions with heparin aqueous solutions. The surface compositions and hydrophilicity of these WPU/heparin blend coatings are characterized by attenuated total reflectance infrared spectroscopy (ATR-FTIR) and water contact angle measurements. These WPU/heparin blend coatings show effectively controlled release of heparin, as determined by the toluidine blue method. Furthermore, the biocompatibility and anticoagulant activity of these blend coatings are evaluated based on the protein adsorption, platelet adhesion, activated partial thromboplastin time (APTT), thrombin time (TT), hemolysis, and cytotoxicity. The results indicate that better hemocompatibility and cytocompatilibity are obtained due to blending heparin into this waterborne polyurethane. Thus, the WPU/heparin blend coating system is expected to be valuable for various biomedical applications.     

Preparation, characterization and electrochemical corrosion studies on environmentally friendly waterborne polyurethane/Na-MMT clay nanocomposite coatings

In this study, we present the first practical evaluation for the corrosion protection effect of waterborne polyurethane (WPU)/Na⁺-montmorillonite (Na⁺-MMT) clay nanocomposite coating. Typically, a series of waterborne polyurethane (WPU)/Na⁺-montmorillonite (Na⁺-MMT) clay nanocomposite materials have been successfully prepared by effectively dispersing the inorganic nanolayers of commercially purified Na⁺-MMT clay in WPU matrix through direct aqueous solution dispersion technique. First of all, WPU was prepared by polymerizing PCL, DMPA and H₁₂MDI, followed by characterized by nuclear magnetic resonance (¹H NMR), Fourier transform infrared (FTIR) and gel permeation chromatography (GPC). Subsequently, the as-prepared PU/Na⁺-MMT clay nanocomposite (Na⁺-PCN) materials were subsequently characterized by FTIR, X-ray diffraction (XRD) patterns and transmission electron microscopy (TEM).PCN materials in the form of coating at low Na⁺-MMT clay loading up to 3 wt% coated on the cold-rolled steel (CRS) coupons were found to exhibit superior corrosion protection effect over those of neat WPU based on a series of electrochemical measurements of corrosion potential, polarization resistance, corrosion current and impedance in 5 wt% aqueous NaCl electrolyte. Effects of the material composition on the gas permeability, thermal stability and optical clarity of neat WPU along with a series of Na⁺-PCN materials, in the form of coating and free-standing film, were also studies by gas permeability analyzer (GPA), thermogravimetric (TGA), differential scanning calorimetry (DSC) and ultraviolet UV-visible transmission spectroscopy, respectively. As control experiments, a series of PU/organo-MMT nanocomposite (denoted by organo-PCN) materials were also prepared for comparative studies.     

Effects of flower-like ZnO nanowhiskers on the mechanical, thermal and antibacterial properties of waterborne polyurethane

A novel waterborne polyurethane/flower-like ZnO nanowhiskers (WPU/f-ZnO) composite with different f-ZnO content (0-4.0 wt%) was synthesized by an in-situ copolymerization process. The f-ZnO consisting of uniform nanorods was prepared via a simple hydrothermal method. In order to disperse and incorporate f-ZnO into WPU matrix, f-ZnO was modified with γ-aminopropyltriethoxysilane. Morphology of f-ZnO in WPU matrix was characterized by scanning electron microscope. The properties of WPU/f-ZnO composites such as mechanical strength, thermal stability as well as water swelling were strongly influenced by the f-ZnO contents. It was demonstrated that appropriate amount of f-ZnO with good dispersion in the WPU matrix significantly improved the performance of the composites. The mechanical property was enhanced with an increase of f-ZnO content up to the optimum content (1 wt%) and then declined. Incorporation of f-ZnO enhanced the water resistance of the composites remarkably. It was amazing to observe that the thermal degradation temperatures of the composites initially decreased significantly and then leveled off with content increase of f-ZnO, which was different from the results of other WPU composite systems reported. Antibacterial activity of WPU/f-ZnO composite films against Escherichia coli and Staphylococcus aureus was also tested. The results revealed that the antibacterial activity enhanced with the increasing f-ZnO content, and the best antibacterial activity was obtained at the loading level of 4.0 wt% f-ZnO.     

纳米木质素/二氧化硅基微胶囊的制备及在自愈合涂层中的应用

利用磷酸化改性木质素/二氧化硅复合纳米颗粒(PAL/SiO₂)作为壁材包埋活性组分异佛尔酮二异氰酸酯(IPDI)制备微胶囊(PAL/SiO₂-IPDI). 通过加入少量反应活性更高的聚合多甲基多二异氰酸酯(PMDI), 与水反应形成聚脲, 以增加微胶囊的壁厚. 采用光学显微镜、 扫描电子显微镜(SEM)和激光粒度分析仪(DLS)研究了PAL/SiO₂复合纳米粒子掺杂量, 水油比和剪切速率对微胶囊表面形貌、 粒径和壁厚的影响. 结果表明, 所制备的微胶囊呈现规整球形, 壁厚为2.36~3.50 μm, 平均粒径为40.3~201.5 μm. IPDI作为芯材包埋在微胶囊中, 芯材含量约为82.8%. 将制备的PAL/SiO₂-IPDI微胶囊添加到环氧树脂中得到自愈合环氧树脂涂层. 其在高盐浓度溶液中的抗侵蚀测试结果显示, 添加质量分数4%的PAL/SiO₂-IPDI微胶囊的环氧树脂涂层在划破后能够快速愈合, 显著降低基底的腐蚀电流和腐蚀速率. 纳米压痕实验表明, 环氧涂层的硬度为249.99 MPa, 而添加PAL/SiO₂-IPDI微胶囊后硬度增加到302.98 MPa, 弹性模量也有提高.     

Optical,electrical, and thermal insulation properties of antimony-doped tin oxide nanoparticles prepared by frozen gel method

Antimony doped tin dioxide (ATO) nanoparticles with different Sb doping contents were prepared by freeze-drying the precursor gel and then calcined procedure. The obtained ATO nanoparticles were characterized by X-ray diffraction, scanning electron microscope, optical and electrical techniques. Results indicated that ATO with 10 mol% Sb doping is optimal, with which had the lowest resistivity and highest transmittance in visible region as well as narrow particle size distribution. Thermal insulation properties of ATO/waterborne polyurethane (WPU) films coating on the glass substrates with different thickness were studied on a DIY heat insulating measurement box and showed that the glass coated with ATO/WPU films possessed better heat-insulating effect than empty glass .     

丝素蛋白与聚氨酯共混膜的制备及结构和性能

采用溶液共混法制备了一系列不同组成的聚氨酯/丝素共混膜.利用红外光谱和广角X-射线衍射表征聚氨酯/丝素共混膜的结构;扫描电镜观察共混膜的断面;紫外-可见光谱测定共混膜的透光性;运用拉伸实验研究不同配比聚氨酯/丝素共混膜的力学性能.结果表明聚氨酯和丝素蛋白分子间存在较强的氢键相互作用.当丝素含量低于3 wt%时,试膜的断面较光滑,丝素蛋白分子进入聚氨酯网状结构中,破坏了聚氨酯分子内硬段和软段间的氢键作用.随着丝素含量进一步增大,丝素小颗粒均匀分散在聚氨酯基体中,二者之间具有较好的相容性.本实验所采用的制膜条件有利于促进丝素蛋白大分子的结晶.丝素蛋白对聚氨酯具有良好的增强效果,当丝素含量从0到5.6 wt%变化时,共混试片的断裂强度由0.56 MPa增大到4.60 MPa,杨氏模量由0.14 MPa增大到1.71 MPa,断裂伸长率从1065%下降到988%.丝素蛋白增强聚氨酯共混膜的强度显著增加,但弹性基本保持不变.     

纳米氧化锡锑改性水性聚氨酯的制备与表征

以异佛尔酮二异氰酸酯(IPDI)、聚醚二醇（N-210）、二羟甲基丙酸（DMPA）、一缩二乙二醇（DEG）、三羟甲基丙烷（TMP）及纳米氧化锡锑（ATO）浆料为主要原料,制备了稳定的纳米ATO改性水性聚氨酯(APU)乳液。 粒径测试及透射电子显微镜（TEM）观察显示,纳米ATO在水性聚氨酯中分散较好,乳液粒径均小于100 nm; FTIR分析表明,纳米ATO粒子与水性聚氨酯(WPU)间可能存在化学键; 热重分析(TGA)测试显示,随纳米ATO添加量的增加,胶膜最大热分解温度逐渐提高,最大提高了约20 ℃;紫外-可见-近红外吸收及保温性能测试表明,随着纳米ATO添加量的提高,胶膜在800~2500 nm的透过率逐渐降低,但涂层在可见光区透过率均超过70%,热阻率由1.34×10-2 m2·℃/W提高至3.17×10-2 m2·℃/W。     

含润滑油微胶囊复合镀铜机理和镀层性能

采用水相分离法制备了以润滑油为囊心、聚乙烯醇为囊壁的微胶囊，并考察了含这种微胶囊复合镀铜层的性能.通过对这种复合镀层微观形貌的观察及耐腐蚀性、耐磨性、动摩擦系数的测定，结果表明由于复合镀铜层中含有润滑油微胶囊，其耐腐蚀性和耐磨性能都得到很大提高，并分析了这种微胶囊复合电沉积的机理和镀层的润滑、修复作用.     

Monocomponent Waterborne Polyurethane Adhesives: Influence of the Crosslinking Agent on Their Properties

To improve the properties of the monocomponent waterborne polyurethane (WPU) adhesives, a series of crosslinked WPU were prepared with trifunctional polyester polyol (P210) as crosslinking agent. The crosslinked WPU dispersions and their films were characterized by conventional methods. The adhesion property of the samples was measured from T-peel test of leather/WPU adhesive/leather joints. Compared with the linear one, the crosslinked WPU exhibited low viscosity, small particle size, and low surface tension. For crosslinked films, the thermal stability, water resistance and mechanical properties were remarkably enhanced. The experimental data of T-peel test indicated that the adhesive strength significantly increased to 4.8 KN/m by crosslinking up to the optimum crosslink index of 1.2 and then showed a small decrease with excess.