低贵金属Pt-Rh型三效催化剂空燃比性能的研究

研究了以浸渍法制备的低贵金属Pt-Rh型三效催化剂对C₃H₈, CO, NO的催化活性. 主要考察了CeO₂-ZrO₂和BaO的添加对催化剂空燃比性能的影响, 通过氧化反应、水气变换和蒸汽重整的性能研究, 探讨了催化剂三效工作窗口扩大的原因. 结果表明, 催化剂中只添加CeO₂-ZrO₂时即具有优异的水气变换性能, 蒸汽重整在250 ℃左右发生, 并且在450 ℃以下时C₃H₈的转化率一直保持在20%左右; BaO添加到含有CeO₂-ZrO₂的催化剂中对水气变换和蒸汽重整则有明显的促进作用, 能进一步扩大催化剂的三效工作窗口; 催化剂中只添加CeO₂-ZrO₂时, 能明显提高催化剂对CO的氧化反应活性, 但对C₃H₈的氧化反应的影响则不明显; BaO和CeO₂-ZrO₂同时存在于催化剂中时, 能进一步提高CO的氧化反应活性, 对C₃H₈的氧化反应则没有明显的促进作用.     

柴油尾气DOC催化剂Pt-Pd/CeO2的活性和抗硫性

采用浸渍法制备了不同Pt、Pd比例的Pt-Pd/CeO₂催化剂,考察了其催化氧化模拟柴油车尾气的活性,并测试了抗硫性。活性测试结果表明,Pt、Pd协同降低了催化剂的起燃温度,其比例对催化剂性能影响很大,其中,Pt_0.2Pd_0.8/CeO₂催化剂在模拟柴油车尾气(丙烯(C₃H₆)、一氧化碳(CO)和一氧化氮(NO))中的催化活性最高;C₃H₆的t₅₀降到170℃,CO的t₅₀降到了150℃,显示了良好的Pt、Pd协同效应;H₂-TPR表征和抗硫性结果分析表明,高比例Pt/Pd催化剂具有更多的表面活性氧,其相对数值与催化剂抗硫性能的关联度高,在催化剂硫酸盐中毒的条件下,更有利于催化反应的进行。     

系列Ln(Ⅲ)配位聚合物(Ln=Eu,Sm,Tb,Pr,Gd)的合成及其荧光分析

采用水热法合成了4个具有1D结构的Ln(Ⅲ)配位聚合物,[Eu₂(C₉H₇O₂)₆(C₉H₇O₂H)(C₂H₅OH)]n(1)、[Sm(C₉H₇O₂)₃]n(2)、[Tb(C₉H₇O₂)₃]n(3)和[Gd(C₉H₇O₂)₃]n(4)(C₉H₈O₂=肉桂酸)。 通过X射线单晶衍射确定了它们的结构。 这4个Ln(Ⅲ)配合物中,Ln(Ⅲ)的配位数均为9,桥配体均为肉桂酸根,但其配位方式有差异。 对配合物进行了IR、UV-Vis-NIR和荧光光谱等表征。 分析了各配合物的荧光发射,结果表明,在可见区,配合物1发射较明显的红光,配合物2、3发射绿光,配合物4发射蓝光,但很弱。 讨论了具有刚柔相混杂性质的肉桂酸配体对配位聚合物的构筑及稀土离子发光的影响。     

异戊二烯聚合催化体系Ln(naph)3-Al(i-C4H9) 3-Al2(C2H5) 3Cl3中稀土金属离子的价态

用光谱法研究了异戊二烯顺-1,4聚合催化体系Ln(napb)₃-Al(i-C₄H₉)₃-Al₂(C₂H₅)₃Cl₃中稀土离子的价态.结果表明,在上述催化体系中,镨,钕,钆,铒部以三价形式存在,这说明上述稀土化合物催化活性的不同,不是因为价态有所差异.对不同条件下含Nd(naph)₃的催化剂溶液的光谱及聚合活性研究结果表明,催化活性与Nd⁺³的特征吸收强度有关,吸收强度愈强,活性愈高.提高铝/钕克分子比及延长催化剂陈化时间,都导致特征吸收强度及催化活性的增大.     

稀土金属间化合物的催化性能——CO及不饱和气相烃在LaNi5上的加氢

本文应用脉冲色谱微型反应器研究了CO,C₂H₄,C₂H₂和C₆H₆在稀土金属间化合物LaNi₅上的催化加氢作用,并且在同一装置上与纯Ni进行了对比。实验结果表明:(1)LaNi₅的催化活性与被加氢物质的性质有关。与纯Ni相比,LaNi₅对被加氢物质所显示的催化效率按下面次序变小:CO>C₂H₄>C₂H₂>C₆H₆,但对苯而言,LaNi₅的活性却比纯Ni低。(2)在H₂中经升温处理过的LaNi₅比未经升温处理的LaNi₅具有更大的催化活性。(3)CO甲烷化反应在LaNi₅及纯Ni上均遵从一级反应速度规律,其活化能分别为15.5Kcal/mole和31Kcal/mole。     

WO3-TiO2负载的Pt单原子催化剂光热协同催化丙烷和丙烯氧化

单原子催化剂(single-atom catalyst,SAC)可以最大化金属原子利用率,并具有独特的电子特性,已经在各种催化反应中进行了广泛的探索。然而,与纳米催化剂相比,贵金属SAC在烃类氧化反应中通常被认为是不活泼的。在本文中,证明了WO₃-TiO₂负载的PtSAC (Pt₁/WO₃-TiO₂)在光热协同催化氧化C₃H₈和C₃H₆这两种典型的挥发性有机化合物(VOCs)中表现出比相应的纳米催化剂(Pt_NP/WO₃-TiO₂)高得多的活性。研究发现,Pt₁/WO₃-TiO₂和Pt_NP/WO₃-TiO₂都可以通过克服氧中毒来提高光热协同催化C₃H₈氧化...     

含有酯基及酰胺基柔链的苯并菲盘状液晶的合成、分子间氢键对柱状介晶性的影响

合成了三个系列, 共二十四个有两种不同软链的对称和非对称苯并菲盘状液晶化合物, C₁₈H₆(OR)₃- (OCH₂COOEt)₃, C₁₈H₆(OR)₃(OCH₂COOBu)₃, C₁₈H₆(OR)₃(OCH₂CONHBu)₃, 其中R＝C₅H₁₁, C₆H₁₃, C₇H₁₅, C₈H₁₇. 化合物通过柱层析纯化, 结构通过¹H NMR, IR, 元素分析等确证. 化合物热稳定性通过TGA测定, 并显示出较高的热稳定性. 通过偏光显微镜和差视扫描量热法对这些化合物的热致液晶性进行了研究. 结果显示: 对于苯并菲液晶化合物C₁₈H₆(OR)₃(OCH₂COOEt)₃, 非对称性化合物较之对称异构体化合物有更低的熔点和更高的清亮点, 因而非对称性化合物有更宽的介晶温度范围. 对于分子中含有酰胺基的苯并菲液晶化合物C₁₈H₆(OR)₃(OCH₂CONHBu)₃, 对称化合物有比非对称异构体更高的清亮点和更有序的六方柱状介晶相, 且其与具有同样软链长度的分子中不含酰胺基的化合物系列C₁₈H₆(OR)₃(OCH₂COOBu)₃相比较, 由于柱内分子间氢键的形成, 不仅有更高的熔点和清亮点, 而且有更丰富的柱状介晶相.     

有玻璃态和液晶态的胆甾烯基苯并菲的合成及介晶性

将盘状液晶基元苯并菲与手性向列型液晶基元胆甾烯基结合的化合物, 可望出现全新的性质. 合成了含有胆甾烯基的苯并菲化合物C₁₈H₆(OC₅H₁₁)₅(OC₅H₁₀COOCh) (2), 2,7-C₁₈H₆(OC₅H₁₁)₄(OC₅H₁₀COOCh)₂ (4), C₁₈H₆(OR)₃(OC_nH_{2nCOO- Ch)3 (R＝C5H11, C7H15, C9H19, C11H23, n＝1, 5, 10) (6a～6f), C18H6(OC5H10COOCh)6 (Ch: cholesteryl) (8). 偏光显微镜和差示扫描量热法对这些化合物的热致介晶性研究结果显示, 化合物 4, 6a～6e具有手性盘状向列相和玻璃态, 8呈现近晶B相(SB)和玻璃态. 随间隔基长度n和烷基链R碳原子数的增加, 化合物玻璃化温度和清亮点呈下降趋势. 随着胆甾烯基数目减少, 化合物的玻璃化温度和清亮点降低.}     

纳米管钛酸CO处理产物的结构及光催化活性

研究了在CO气流中,处理温度对纳米管钛酸(NTA)脱水产物TiO₂的结构及C₃H₆光催化氧化反应活性的影响.结果表明:NTA经CO高温处理后,样品未发生C掺杂,只有碳沉积发生;随着处理温度的升高,样品的比表面积大幅下降,与NTA在空气中焙烧处理相比,由锐钛矿向金红石TiO₂转变的温度提前;CO处理后产物对C₃H₆均未表现出可见光催化性能,但具有紫外光催化活性,随着在CO气氛中处理温度的升高,紫外光催化活性降低.     

稀土吲哚-3-乙酸和吲哚-3-丁酸配合物的合成、表征及成键特性研究

在乙醇水溶液体系中合成了8种新的稀土吲哚-3-乙酸和吲哚-3-丁酸配合物,其通式为Ln(lA)₃·2H₂O和Ln(IB)₃·2H₂O(Ln=La,Nd,Sm,Er;IA=C₁₀H₈NO₂;IB=C₁₂H₁₂NO₂)。用元素分析、电导测定、电子吸收光谱、红外光谱、X光电子能谱和热重-差热分析确定了配合物的组成和成键特性。     

Oxidative dehydrogenation of ethane to ethylene over NiO loaded on high surface area MgO

The oxidative dehydrogenation of ethane over NiO-loaded MgO with high surface area was carried out using a fixed-bed flow reactor at 600 °C under atmospheric pressure.

At 600 °C, the oxidative dehydrogenation of ethane (C₂H₆/O₂ = 1) without dilution with an inert gas resulted in C₂H₆ conversion of 68.8% and a high C₂H₄ selectivity of 52.8%, which corresponds to a C₂H₄ yield of 36.3%. In addition, the catalytic activity did not decrease for at least 10 h. X-ray photoelectron spectra of the catalysts after the reaction exhibited that the initial valence state of Ni²⁺ (NiO) was maintained during the oxidative dehydrogenation of ethane. However, when NiO-loaded MgO was reduced with H₂ prior to the reaction, C₂H₄ selectivity decreased to nearly zero and high CO and H₂ selectivities were observed with the C₂H₆ conversion of 50 %, indicating that partial oxidation of C₂H₆ proceeded. Therefore, it seems important to keep Ni species as an oxide phase on the support, and for this purpose, use of the high surface area of MgO is essential.     

乙烯在钯圆盘电极的电化学氧化研究（英文）

由于巨大的潜在市场,乙烯的电化学氧化受到愈来愈多的关注。目前,主流的电化学氧化法仍以依赖于氧化还原媒介的介导氧化法为主,而这些媒介的使用在电解过程中产生大量的腐蚀性中间体,使其实际应用受到阻碍。直接电氧化法可有效规避此问题,但又受到低活性和低选择性的限制。在本工作中,我们针对目前最先进的钯催化直接氧化体系,在中性条件下开展了一系列电化学研究,以对该过程的机理获取更深入的认识。在氮气和乙烯氛围下,钯电极的循环伏安谱图有显著区别。我们发现电解过程中生成的Pd(Ⅱ)物种在乙烯氛围下可绕过原本的电化学还原路径,通过一个化学步还原为Pd(0),因此可能是乙烯氧化的活性位点。Pd(Ⅱ)物种所对应的还原峰也因此可作为乙烯吸附的数量的指标。通过电化学脉冲序列的设计,我们在钯催化剂上识别了两种具有不同吸附强度的乙烯,其强、弱吸附模式所对应的电荷转移比例约为0.3:1。弱吸附的乙烯在钯电极表面表现出可逆的吸脱附行为,而具有强吸附模式的乙烯无法通过物理过程脱附,可能指向到乙烯深度氧化过程。这项工作为进一步设计高性能乙烯直接电氧化催化剂提供了设计思路和方向。     

Four unit linking groups IV. Liquid crystals of positive dielectric anisotropy

Three separate series of new materials of weak to strongly positive dielectric anisotropy have been prepared. Each series contains four sub-sets of materials each incorporating a different four unit linking group (i.e., C₄H₈, C₄H₆, C₃H₆O and C₃H₄O) and the same series of end groups (i.e. F, CN and OCF₃) in various substitution patterns. The synthesis and liquid crystal transition temperatures of these novel substances are described and compared with those of the corresponding materials incorporating standard central linkages (i.e.-, C₂H₄, CH₂O, COO). The effect of an additional trans carbon-carbon double bond in the terminal alkyl chain and in the central linking unit has also been studied.     

富氧条件下Fe-Mn/Beta选择性催化丙烯还原氮氧化物

以Beta分子筛为载体，采用等体积浸渍法制备Fe-Mn/Beta催化剂，并对其在富氧条件下丙烯选择性催化还原NO性能进行了研究。通过N₂吸附-脱附、X射线衍射（XRD）、X射线光电子能谱（XPS）、透射电子显微镜（TEM）、程序升温还原（H₂-TPR）和原位漫反射傅里叶变换红外光谱（in-situ DRIFTS）等研究手段对催化剂进行表征，考察Mn组分对催化剂的物理化学性质、C₃H₆-SCR反应活性和反应中间产物的影响。结果表明，引入Mn物种可以显著提高Fe-Mn/Beta催化剂的低温催化活性，1.5Fe1.0Mn/Beta催化剂NO还原效率350℃最高可达99.4%，在250-400℃反应温度下显示出很高的反应活性和N₂选择性。原位红外光谱研究表明，分子筛离子交换位上孤立的铁离子是丙烯选择性氧化的主要活性位，分散良好的MnO₂物种不能提高催化剂对丙烯的活化能力，但有助于促进形成NO₂吸附物种，从而提升了Fe-Mn/Beta催化剂的低温C₃H₆-SCR性能。经高温水热老化处理后，Fe-Mn/Beta催化剂脱硝活性明显下降，这与孤立的Fe³⁺离子迁移形成Fe_xO_y团聚物种有关。     

Supported transition-metal catalysts for the C---C coupling reaction between ethene and diazoalkanes

The preparation of a series of immobilized transition-metal catalysts are reported. The catalysts were obtained by chemisorption of either rhodium(I) or iridium(I) complexes [MX(C₂H₄)₂]_n (M = Rh, Ir; X = Cl, OAc, acac, f₃-acac, f₆-acac) on SiO₂ or MgO supports. The oxides were also activated by SiCl₄ or TiCl₄ to give support materials in which the acidic nature of the surface is substantially increased. The activity of the immobilized catalysts was tested, particularly in the reaction of ethene with diphenyldiazomethane which yields a mixture of 1.1-diphenylpropene (8) and 1.1-diphenylcyclopropane (9). It was found that the most active and most selective (highest ratio 8:9) catalyst B1 was formed support material B (SiO₂ activated by SiCl₄) and [RhCl(C₂H₄)₂]₂ (1) and that both the activity and selectivity of B1 was comparable with that of complex 1 in solution. In contrast, the supported catalysts A2, D2 and A3, D3 obtained from [Rh(OAc)(C₂H₄)₂]₂ (2) and [Rh(acac)(C₂H₄)₂] (3) were less active than compounds 2 and 3 in solution. The immobilized catalysts A6, A7, D7 and E7, which were generated from the chloro- and acetatoiridium(I) complexes [IrCl(C₂H₄)₂]₂ (6) and [Ir(OAc)(C₂H₄)₂]₂ (7), possessed a lower activity than the rhodium counterparts. With diazoalkanes other than Ph₂CN₂, the activity of the supported catalyst B1 was partly higher and partly lower than that of complex 1 in the homogeneous phase.     

C_6H_2(OH)_3CH_3氧化成羟基苯甲酸反应路径的DFT研究

运用密度泛函(DFT)理论,采用Materials Studio 8.0,用GGA/BP方法研究了C_6H_2(OH)_3CH_3氧化成羟基苯甲酸的反应路径。结果表明,甲基上的氢原子被氧化成羟基以及羟基被氧化为醛基及醛基被氧化成羧基均为放热过程。分子C_6H_2(OH)_3CH_3中甲基氧化成羧基的主路径为三个氢原子氧化反应路径,其路径为C_6H_2(OH)_3CH_3+3O→C6H2(OH)3C(OH)3→C6H2(OH)3COOH+H2O,该路径受限于羟基直接被氧化成羧基过程,需克服130 k J/mol的反应势垒,反应速率常数对数ln(k)为-22.96 s-1;醛基、羟基优先被氧化成羧基的顺序为:-CHO-C(OH)3-HC(OH)2-H2C(OH);提高反应温度、氧气浓度均有利于羟基苯甲酸的生成,适当的催化剂有利于促进整个反应的进行。     

CeO2的添加对柴油车氧化催化剂Pt/SiO2-Al2O3的NO氧化性能提高的影响

The catalytic activities for NO oxidation achieved by different amounts of CeO₂-modified Pt/SiO₂-Al₂O₃ catalysts Pt/SiO₂-Al₂O₃-wCeO₂ (the mass fraction w being 0%, 5%, 10%, 15%, 30%), prepared using step-wise impregnation, were investigated in the presence and absence of CO and C₃H₆. The results showed that the NO oxidation activity could be efficiently improved by modification of CeO₂, wherein the 15%-CeO₂-modified catalyst exhibited the maximum NO conversion of 61% even in the presence of CO and C₃H₆, which were proved to inhibit NO₂ formation in this study. A series of characterization methods were performed over the as-prepared samples to correlate their surface and structural characteristics with their enhanced NO oxidation activities. CO-chemisorption illustrated that appropriate CeO₂-loading was effective for enhancing Pt dispersion, thus enhancing Pt surface-to-volume ratio, confirmed by transmission electron microscope (TEM) images. X-Ray Diffraction (XRD) further suggested that ceria addition could suppress the growth of the Pt crystal, resulting in higher surface Pt atomic ratio. Further, H₂ temperature-programmed reduction (H₂-TPR), together with TEM results, implied that the presence of ceria could enhance the interaction between metal and supports, thus facilitating reducibility of both active platinum and ceria. Hence, this study displays that ceria could act as a dispersion promoter and a reducibility booster, both of which are beneficial to NO oxidation activity. The improved NO oxidation activity is significant for the efficient purification of diesel integrated catalytic system.     

CO and C3H8 Total Oxidation over Pd Catalysts Supported on Commercial Ce-Zr Solid Solution: Effects of the Calcination Temperature and Hydrothermal Treatment

A series of Pd catalysts supported on commercial Ce-Zr solid solution(Pd/CZ) calcined at different temperatures(750, 900 and 1050 ℃) was prepared via an incipient wetness impregnation method. The activities of the fresh and hydrothermally aged Pd/CZ catalysts were tested for total oxidation of CO and C₃H₈. For CO oxidation, the activity of either fresh or aged Pd/CZ catalysts decreased with the elevating of calcination temperature of CZ support, with a fresh catalyst calcined at 750 ℃ possessing the highest activity and hydrothermal stability. For C₃H₈ total oxidation, the activity of Pd/CZ catalysts could be improved by increasing the calcination temperature of support. However, the aged Pd/CZ catalysts showed higher activity than corresponding fresh Pd/CZ catalysts. The turnover frequency(TOF) over Pd/CZ catalyst for CO oxidation increased with increasing reduction ability of the catalysts, with a fresh catalyst calcined at 750 ℃ having the highest value(0.27 s^-1). However, the TOF of Pd/CZ catalyst for C₃H₈ total oxidation was mainly affected by the size of Pd particles, and large Pd particles possessed a higher activity, with the highest TOF value(0.96 s^-1) obtained over an aged catalyst calcined at 1050 ℃.     

联苯基桥连双核茂锆化合物的合成及催化乙烯聚合

4,4′-二溴联苯与n-BuLi反应得到对-联苯基二锂,再与四甲基环戊烯酮进行羰基加成,酸催化脱水,一步得到对-联苯基桥连四甲基环戊二烯配体4-(C₅Me₄H)C₆H₄-C₆H₄(C₅Me₄H)-4(1).配体1相继与n-BuLi和ZrCl₄反应得到相应的联苯基桥连双(单茂三氯化锆)4-(C₅Me₄ZrCl₃)C₆H₄-C₆H₄(C₅Me₄ZrCl₃)-4,不经分离直接与环戊二烯基锂或茚基锂反应得到相应的双核锆化合物4-(C₅MeZrCl₂Cp′)C₆H₄-C₆H₄·(C₅Me₄ZrCl₂Cp′)-4[Cp′=C₅H₅(2),C₉H₇(3)].研究了在MAO(MethylAluminoxane)助催化下,化合物2和3对乙烯聚合的催化性能.化合物2和3都显示了非常高的催化活性,并在较高的温度下达到最高活性.