Ru/CNTs-Al2O3氨合成催化剂的制备与表征

采用H₂O₂、HNO₃和空气等氧化剂(ox)对碳纳米管-氧化铝(CNTs-alumina)复合材料进行纯化改性处理, 制备了Ru/CNTs-alumina-ox系列催化剂. 透射电镜(TEM), 热重(TG), X射线衍射(XRD)和傅里叶变换红外(FTIR)光谱分析结果表明, CNTs-alumina-H₂O₂复合载体中碳管结晶度最好, 且部分碳管被打断, 长度变短, 使其表面的羟基、羧基和羰基的含量明显提高. 电感偶合等离子体发射光谱(ICP)分析结果还表明, 经HNO₃处理时CNTs-alumina-HNO₃复合载体中有Al的溶出, 溶液中Al含量为49.98 mg·g^-1. 经三种氧化剂处理后所得到的催化剂, 其结构和表面化学性质存在明显的差别, 影响了氨合成催化剂的活性, 其中以CNTs-alumina-H₂O₂复合载体制备的催化剂氨合成活性最高, 在10 MPa、425 °C、10000 h^-1条件下, Ru/CNTs-alumina-H₂O₂催化剂氨合成反应速率达到39.8 mmol·g^-1·h^-1.     

多壁碳纳米管负载Fe3O4磁性纳米粒子表面吸附增强过氧化酶的催化活性

采用共沉淀法制备了Fe3O4磁性纳米粒子,将其负载于氨基吡啶修饰多壁碳纳米管(MWCNT-AP)上,得到具有良好的分散性和超顺磁性的Fe3O4/MWCNT-AP复合物.通过傅里叶变换红外(FT-IR)光谱、X射线衍射(XRD)和磁滞回线测量等方法对Fe3O4/MWCNT-AP复合物进行了表征.扫描电镜(TEM)结果表明:Fe3O4磁性纳米粒子多集中于碳纳米管MWCNT-AP的端部,形成的复合物在极性溶剂中具有良好的分散性和超顺磁性;辣根过氧化酶(HRP)可通过物理作用吸附于Fe3O4/MWCNT-AP复合物表面.酸性条件下(pH 4.0),Fe3O4/MWCNT-AP复合物使HRP的最大反应速率(Vmax)提高了3倍.     

十二烷基硫酸钠水溶液的动态表面吸附性质

利用MPTC型气泡压力张仪研究了十二烷基硫酸钠(SDS)溶液在不同NaCl 浓度下的动态表面吸附性质, 分析了离子型表面活性剂在表面吸附层和胶束中形成双电层结构产生表面电荷对动态表面扩散过程和胶束性质的影响. 结果表明, SDS在表面吸附过程中, 表面电荷的存在会产生5.5 kJ·mol^-1的吸附势垒(E_a), 显著降低十二烷基硫酸根离子(DS^-)的有效扩散系数(D_eff). 十二烷基硫酸根离子的有效扩散系数与自扩散系数(D)的比值(D_eff/D)仅为0.013, 这表明SDS与非离子型表面活性剂不同, 在吸附初期为混合动力控制吸附机制. 加入NaCl可以降低吸附势垒. 当加入不小于80 mmol·L^-1 NaCl后, E_a小于0.3 kJ·mol^-1, D_eff/D在0.8-1.2之间, 表现出与非离子型表面活性剂相同的扩散控制吸附机制. 同时, 通过分析SDS胶束溶液的动态表面张力获得了表征胶束解体速度的常数(k₂). 发现随着NaCl 浓度的增大, k₂减小, 表明SDS胶束表面电荷的存在会增加十二烷基硫酸根离子间的排斥力, 促进胶束解体.     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明：合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明：最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

氧-硼共修饰多壁碳纳米管载铂催化剂的制备及氧还原活性

采用一种简便的方法,合成了氧-硼共修饰的多壁碳纳米管材料,以此为载体制备的铂基催化剂具有更小的铂粒径、更高的电化学表面积(40 m²·g_Pt^-1)和更高的氧还原活性(0.3 A·mg_Pt^-1)。氧、硼在提高碳纳米管的载体分散性、控制铂颗粒的均匀性和粒径、促进氧还原反应的氧吸附/解离方面发挥着重要的作用。     

ZnCr双金属层状材料对废水中酸性红14的吸附性能

采用共沉淀法制备性能优异的层状材料锌铬水滑石(Zn_xCr-LDHs, x=2, 3, 4), 并探究各种因素对吸附酸性红14(AR14)的影响。XRD、ICP、FTIR及BET表征结果表明:合成的Zn_xCr-LDHs晶型良好且稳定, 具备介孔结构。实验结果表明:最佳吸附剂为Zn₃Cr-LDHs, 比表面积为101 m²·g^-1, 对AR14的最大吸附容量为484.63 mg·g^-1。同时, 降低溶液pH值和提高溶液温度均可促进AR14的吸附。该吸附过程分别符合准二级动力学模型和Freundlich等温吸附模型。结合Materials Studio 5.5软件模拟, 推测该吸附机理主要以表面吸附为主, -SO₃^-基团是反应点。     

聚乙烯亚胺改性氧化石墨对水中Cr(Ⅵ)的吸附

通过对石墨氧化、酯化,将聚乙烯亚胺耦合接枝到氧化石墨表面,制备聚乙烯亚胺改性氧化石墨(PEI-GO)。通过FTIR、XRD、TEM、RS和XPS等对合成材料进行表征,并研究了其对水中的Cr(Ⅵ)吸附和脱附性能。表征结果表明,聚乙烯亚胺成功嫁接到氧化石墨上,其氨基含量为4.36mmol·g^-1。PEI-GO对水中Cr(Ⅵ)具有很好的吸附性能,吸附等温线符合Freundlich方程,吸附动力学可用拟二级动力学方程来描述。PEI-GO对水中Cr(Ⅵ)的吸附随pH的升高而降低。阴离子的存在降低吸附剂对Cr(Ⅵ)的吸附,不同阴离子的影响大小顺序为PO₄^3- >SO₄^2- >NO₃^- >Cl^-。XPS结果表明,PEI-GO对Cr(Ⅵ)的去除是吸附-化学还原耦合作用的结果。经4次脱附再生循环,PEI-GO对Cr(VI)仍具有较高吸附量,表明该吸附剂再生性好,可循环使用。     

多壁碳纳米管/聚丙烯酸/MOF-5的制备及其N2吸附性能

用化学修饰法制备出复合物多壁碳纳米管/聚丙烯酸(MWCNTs/PAA),用溶剂热法合成Zn₄O(1,4-benzenedicarboxylate)₃(MOF-5)和MWCNTs/PAA/MOF-5。通过XRD、FTIR、TG、HRTEM和比表面积和孔隙度分析仪对MWCNTs,MOF-5,MWCNTs/PAA和MWCNTs/PAA/MOF-5的结构和性质进行表征。结果表明:复合材料MWCNTs/PAA中PAA包覆在碳纳米管外壁上,含量为4.3%,在FTIR中有PAA特征官能团的吸收峰;MWCNTs/PAA/MOF-5和MOF-5的形貌一样,MWCNTs/PAA/MOF-5的热分解温度比MOF-5的提高了49℃;MOF-5和MWCNTs/PAA/MOF-5的N₂吸附曲线为Ⅰ型,77K和100kPa条件下,N₂的吸附量达到最大值,分别为265、299.03 cm³·g^-1。     

聚乙烯亚胺改性氧化石墨对水中Cr(Ⅵ)的吸附

通过对石墨氧化、酯化,将聚乙烯亚胺耦合接枝到氧化石墨表面,制备聚乙烯亚胺改性氧化石墨(PEI-GO).通过FTIR、XRD、TEM、RS和XPS等对合成材料进行表征,并研究了其对水中的Cr(Ⅵ)吸附和脱附性能.表征结果表明,聚乙烯亚胺成功嫁接到氧化石墨上,其氨基含量为4.36 mmol·g^-1.PEI-GO对水中Cr(Ⅵ)具有很好的吸附性能,吸附等温线符合Freundlich方程,吸附动力学可用拟二级动力学方程来描述.PEI-GO对水中Cr(Ⅵ)的吸附随pH的升高而降低.阴离子的存在降低吸附剂对Cr(Ⅵ)的吸附,不同阴离子的影响大小顺序为PO₄^3- >SO₄^2- >NO^3- >Cl^-.XPS结果表明,PEI-GO对Cr(Ⅵ)的去除是吸附-化学还原耦合作用的结果.经4次脱附再生循环,PEI-GO对Cr(VI)仍具有较高吸附量,表明该吸附剂再生性好,可循环使用.     

H2在K0-MWCNTs上储存和吸附/脱附特性研究

利用高压容积法辅以卸压升温脱附排水法, 测定金属K修饰多壁碳纳米管对H₂的吸附储存容量. 结果表明, 在室温(25 ℃), 7.25 MPa实验条件下, x%K⁰-MWCNTs (x%＝30%～35%, 质量百分数)对H₂的吸附储存容量可达3.80 wt%(质量百分数), 是相同条件下单纯MWCNTs氢吸附储量的2.5倍; 室温下卸至常压的脱附氢量为3.36 wt%(占总吸附氢量的～88%), 后续升温至673 K的脱附氢量为0.41 wt%(占总吸附氢量的～11%). 利用LRS和H₂-TPD-GC/MS等谱学方法对H₂/K⁰-MWCNTs吸附体系的表征研究表明, H₂在K⁰-MWCNTs上吸附存在非解离 (即分子态)和解离(即原子态)两种吸附态; 在≤723 K温度下, H₂/K⁰-MWCNTs体系的脱附产物几乎全为H₂气; 723 K以上高温脱附产物不仅含H₂, 也含有CH₄, C₂H₄和C₂H₂等C₁/C₂-烃.     

基于多层酶/纳米金固定甲胎蛋白免疫传感器的研究

>利用自组装技术和静电吸附作用, 将甲胎蛋白抗体(anti-AFP)固定在多层辣根过氧化物酶/纳米金及L-半胱胺酸修饰的金电极表面, 制备出用于检测甲胎蛋白抗原(AFP)的无试剂型免疫传感器. 通过交流阻抗技术、循环伏安法和计时电流法考察了电极的电化学特性, 并对该免疫传感器的作用机理及性能进行了详细的研究. 用计时电流法测得AFP的线性范围为1.0～10.0和10～200 ng•mL^－1, 检出限为0.5 ng•mL^－1. 实验结果表明, 该方法提高了抗体的固定量, 增强了传感器的灵敏度和稳定性, 且该传感器响应迅速、选择性好, 血清中常见抗原不干扰测定. 将其用于临床血清检验, 与放射免疫测定法(RIA)的符合率为86.7%.     

Covalent immobilization of horseradish peroxidase via click chemistry and its direct electrochemistry

A simple and versatile approach for covalent immobilization of redox protein on solid surface via self-assembled technique and click chemistry is reported. The alkynyl-terminated monolayers are obtained by self-assembled technique, then, azido-horseradish peroxidase (azido-HRP) was covalent immobilized onto the formed monolayers by click reaction. The modified process is characterized by reflection absorption infrared spectroscopy (RAIR), surface-enhanced Raman scattering spectroscopy (SERS) and electrochemical methods. All the experimental results suggest that HRP is immobilized onto the electrode surface successfully without denaturation. Furthermore, the immobilized HRP shows electrocatalytic reduction for H₂O₂, and the linear range is from 5.0 to 700 μM. The heterogeneous electron transfer rate constant k_s is 1.11 s⁻¹ and the apparent Michaelis-Menten constant is calculated to be 0.196 mM.     

Cationic Dye Modified Sawdust as Electrode Modifier for Electrochemical Detection of Anions

Because of its chemical properties, sawdust displays poor anionic exchange capacity. Here we demonstrate that sawdust modification with methylene blue (MB) dye represents an interesting and facile alternative to render this natural biomaterial capable to accumulate anionic species. MB adsorption onto sawdust was monitored by cyclic voltammetry and experimental parameters carefully optimized. Under the ideal experimental conditions (composition of accumulation and desorption solution, accumulation and desorption time and the nature of the electrolytic solution), the adsorbed MB showed poor mobility, which results in the absence of the characteristic electrochemical signal of MB. The ability of the material to accumulate anionic species was thus evaluated using Fe(CN)₆^3? as a model anions. The slow Fe(CN)₆^3?/4? system recorded onto the electrode modified by pristine sawdust (P/SFE) become fast and reversible after immobilization of MB onto P/SFE (MB/SFE). Electrochemical impedance spectroscopy confirms this result through the spectacular decrease of charge transfer resistance after MB adsorption (from 83 kΩ on P/SFE to 637 Ω on MB/SFE). MB/SFE was applied to the electroanalysis of nitrites and a sensitivity of 7.4 μA mM^?1 was obtained. Although this sensitivity was less important compared to that obtained on glassy carbon electrode (9.4 μA mM^?1), the dye modified electrode displays by far the best reproducibility even at higher nitrite concentration.     

Role of solution chemistry on the trapping of radionuclide Th(IV) using titanate nanotubes as an efficient adsorbent

Titanate nanotubes (TNTs) have attracted great interest in multidisciplinary study since their discovery. The adsorption of thorium [Th(IV)] onto TNTs in the absence and presence of humic acid (HA)/fulvic acid (FA) was studied by batch technique. The influence of pH from 2.0 to 10.0, ionic strength from 0.001 to 0.1 mol L^?1 NaClO₄, and coexisting electrolyte cations (Li⁺, Na⁺, K⁺) and antions (ClO₄ ^?, NO₃ ^?, Cl^?) on the adsorption of Th(IV) onto TNTs was tested. The adsorption isotherms of Th(IV) was determined at pH 3.0 and analyzed with Langmuir and Freundlich adsorption models, respectively. The results demonstrated that the adsorption of Th(IV) onto TNTs increases steeply with increasing pH from 2.0 to 4.0. Generally, HA/FA was showed to enhance Th(IV) adsorption onto TNTs at low pH values, but to reduce Th(IV) adsorption onto TNTs at high pH values. The adsorption of Th(IV) onto TNTs was also dependent on coexisting electrolyte ions in aqueous solution under our experimental conditions. The adsorption of Th(IV) onto TNTs is exothermic and spontaneous. The findings indicating that TNTs can be used as a promising candidate for the enrichment and solidification of Th(IV) or its analogue actinides from large volume solution in real work.     

碳纳米管/聚氨酯杂化膜的原位聚合构建及气体渗透性能

采用H2SO4/HNO3混酸处理得到不同氧化程度的多壁碳纳米管(MWCNT-COOH),再通过与4,4′-二苯基甲烷二异氰酸酯(MDI)、1,4-丁二醇(BDO)的预聚和扩链反应构建碳纳米管/聚氨酯(MWCNT-COOH/PU)杂化膜。利用傅里叶红外光谱(FTIR)、拉曼光谱(Raman)和透射电子显微镜(TEM)等分析表征多壁碳纳米管结构;探讨了多壁碳纳米管氧化程度和填充量对MWCNTCOOH/PU杂化膜的形貌和CO2、N2渗透性能的影响。结果表明,混酸处理后的多壁碳纳米管带有一定的含氧基团,并随氧化程度的提高,多壁碳纳米管的拉曼光谱G峰和D峰的强度之比(ID/IG)有所增大;氧化程度对多壁碳纳米管在溶剂和杂化膜中的分散性有较大影响,氧化程度越高,分散性越好;杂化膜的CO2、N2渗透性及CO2/N2渗透选择性随多壁碳纳米管氧化程度的增加有所增大,而随多壁碳纳米管填充量的增加表现出先增大后减小的趋势,当氧化程度较高的多壁碳纳米管(H-MWCNT-COOH)填充量为1.0wt%时,H-MWCNT-COOH/PU杂化膜的CO2渗透系数为67.8 Barrer,CO2/N2渗透选择性可达45,表明适量填充MWCNT-COOH能显著提高MWCNT/PU杂化膜的CO2渗透性及CO2/N2的渗透选择性。     

Attachment of horseradish peroxidase (HRP) onto the poly(styrene/acrolein) latexes and onto their derivatives with amino groups on the surface; activity of immobilized enzyme

The polystyrene (P(S)), poly(styrene/acrolein) (P(SA)), and polyacrolein (P(A)) latexes, with varied fraction of polyacrolein in the surface layer (f _A=0, 0.50, 0.63, 0.84, 1.00), were used for the attachment of horseradish peroxidase. Surfaces of latexes were modified by reaction with ethylenediamine. In this step the aldehyde groups from polyacrolein were blocked and the primary amino groups were introduced. The carbohydrate portion of HRP was oxidized in the reaction leading to formation of aldehyde groups. The adsorption and covalent immobilization of HRP onto the P(S), P(SA), and P(A) latexes and of the oxidized HRP (HRP-OX) onto the modified latex particles, with amino groups on the surface (P(SA)-M and P(A)-M), were investigated. The activities of parent and oxidized HRP were compared with activities of the corresponding enzymes in solution. It has been found that whereas HRP is not suitable for the covalent immobilization on P(SA) latex and loses its activity after adsorption onto P(S) latex, HRP-OX can be adsorbed onto P(S) latex and is readily immobilized covalently onto the ethylenediamine modified P(SA) and P(A) latexes, retaining much of its former enzymatic reactivity.This work was supported by the KBN Grant 2 0624 91 01     

碳纳米管/聚氨酯杂化膜的原位聚合构建及气体渗透性能

采用H₂SO₄/HNO₃混酸处理得到不同氧化程度的多壁碳纳米管（MWCNT-COOH）,再通过与4,4’-二苯基甲烷二异氰酸酯（MDI）、1,4-丁二醇（BDO）的预聚和扩链反应构建碳纳米管/聚氨酯（MWCNT-COOH/PU）杂化膜。利用傅里叶红外光谱（FTIR）、拉曼光谱（Raman）和透射电子显微镜（TEM）等分析表征多壁碳纳米管结构;探讨了多壁碳纳米管氧化程度和填充量对MWCNT-COOH/PU杂化膜的形貌和CO₂、N₂渗透性能的影响。结果表明,混酸处理后的多壁碳纳米管带有一定的含氧基团,并随氧化程度的提高,多壁碳纳米管的拉曼光谱G峰和D峰的强度之比（I_D/I_G）有所增大;氧化程度对多壁碳纳米管在溶剂和杂化膜中的分散性有较大影响,氧化程度越高,分散性越好;杂化膜的CO₂、N₂渗透性及CO₂/N₂渗透选择性随多壁碳纳米管氧化程度的增加有所增大,而随多壁碳纳米管填充量的增加表现出先增大后减小的趋势,当氧化程度较高的多壁碳纳米管（H-MWCNT-COOH）填充量为1.0wt%时,H-MWCNT-COOH/PU杂化膜的CO₂渗透系数为67.8Barrer,CO₂/N₂渗透选择性可达45,表明适量填充MWCNT-COOH能显著提高MWCNT/PU杂化膜的CO₂渗透性及CO₂/N₂的渗透选择性。     

连续在线原位ATR-FTIR技术测定介孔CuAl2O4对黄药的吸附

以丁胺和正十二醇为混合模板剂, 采用共沉淀法制备了介孔纳米CuAl₂O₄. 用X射线粉末衍射(XRD)、傅里叶变换红外(FTIR)光谱、N₂吸附-脱附对产物的结构进行了表征. 采用连续在线原位衰减全反射傅里叶变换红外(ATR-FTIR)光谱技术研究了水溶液中丁基和辛基黄药在介孔CuAl₂O₄表面的吸附. 随着吸附时间的延长,1200 和1040 cm^-1两处黄药特征峰的高度逐渐增加, 根据1200 cm^-1处C-O-C伸缩振动峰的变化来评价黄药在CuAl₂O₄表面的吸附动力学过程. 结果表明, 介孔纳米CuAl₂O₄对黄药有很强的吸附能力, 在100 min 的时间内, CuAl₂O₄样品对丁基和辛基黄药的吸附量分别达到了236 和300 mg·g^-1, 且属于化学吸附. 对实验数据进行理论模拟, 发现吸附过程更接近于拟二级吸附动力学方程.     

Layered Zirconium(IV) Aminoethylphosphonate Intercalated with Horseradish Peroxidase for an Amperometric Biosensor

Layered zirconium(IV) aminoethylphosphonate (ZrAEP) have been used as matrices for immobilization of horseradish peroxidase (HRP) to fabricate enzyme electrode for an amperometric biosensor. The biocompatible HRP–ZrAEP films were fabricated on gold electrode surface by electro‐co‐deposition method. The morphology of the HRP–ZrAEP composite was characterized by scanning electron microscopy (SEM). UV–vis spectroscopy indicated that the intercalated HRP retained its native structure after incorporation in the ZrAEP. The immobilized HRP at the HRP–ZrAEP films exhibited good electro catalytic responses to the reduction of hydrogen peroxide. The response time of the biosensor was less than 3 s, and the linear range is from 2.5 × 10^?6 to 3.22 × 10^?3 M, with a detection limit of 7.0 × 10^?7 M (S/N = 3). The Michaelis–Menten constant (K^app_M) value is estimated to be 2.21 mM. In addition, the obtained biosensor possesses high sensitivity, good stability and reproducibility.     

磁性壳聚糖复合微球的制备及其Cu2+吸附性能

以球磨后的粉煤灰磁珠（MS）颗粒为磁核,通过溶胶凝胶法和反相微乳液法依次包覆SiO₂和壳聚糖（CS）,制备了MS@SiO₂@CS磁性微球。利用扫描电镜及能量色散谱仪、热重分析仪、红外光谱仪、X射线衍射仪、振动样品磁强计对所得样品的结构和磁性进行了系统表征。结果表明,磁珠颗粒表面实现了逐层包覆,较均匀的分散于壳聚糖基体中,MS@SiO₂@CS微球的比饱和磁化强度可达7.04 emu·g^-1。Cu²⁺离子吸附实验表明,所得磁性壳聚糖微球对Cu²⁺具有良好的吸附能力,最大吸附量可达11.08 mg·g^-1;而且可通过磁选法高效固液分离。吸附动力学研究表明,MS@SiO₂@CS微球对Cu²⁺离子的吸附符合准二级动力学模型,以化学吸附为主。