不同形貌TiO2的水热合成及对苯酚的降解研究

采用水热合成法, 通过对溶液的pH值、反应物配比、陈化温度及陈化时间等条件的控制, 合成出不同晶型及形貌的TiO2纳米粒子. 结果表明, 溶液的pH＝11, n(钛酸丁酯):n(三乙醇胺)＝1:2, 陈化温度为150 ℃, 陈化时间为48 h时, 能得到较规则的、长径比约为4:1的棒状TiO2. 当溶液pH<10时, 得到球形的TiO2纳米粒子; 陈化时间为24 h时, 得到纺锤形TiO2纳米晶. 以上合成的纳米粒子均为锐钛矿型, 但当溶液的pH>12时, 则得到板钛矿型TiO2粒子. 以苯酚为降解模型, 考察了不同形貌TiO2的光催化活性.     

TiO_2纳米粒子的表面修饰研究

利用表面修饰法合成了油酸 (OA)修饰的TiO2 纳米粒子 ,采用红外光谱 (IR)、透射电子显微镜 (TEM)和X射线光电子能谱 (XPS)对表面修饰的TiO2 纳米粒子进行了结构表征 ,并研究了油酸浓度对TiO2 表面覆盖量及在油中分散性能的影响 .研究结果表明通过油酸表面修饰 ,成功合成了具有油分散性能的纳米TiO2 ,并且获得了油酸修饰量与TiO2 的最佳配比 .     

WC/TiO2纳米复合材料的制备及其电催化性能

以TiCl4为原料, 采用溶胶水解法合成了金红石型纳米TiO2颗粒, 并以其为载体制备了WC/TiO2纳米复合材料. 采用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线能谱(EDS)等手段分析了WC/TiO2纳米复合材料的晶相组成和表面形貌. 结果显示样品是由WC, TiO2和W组成, 纳米WC颗粒均匀地包覆在TiO2的表面, 并与TiO2构成了WC/TiO2纳米复合材料. 采用循环伏安法和计时电流法研究了WC/TiO2纳米复合材料对硝基苯的电催化性能. 结果表明, WC/TiO2纳米复合材料对硝基苯的电催化活性和电化学稳定性均优于介孔结构碳化钨(meso-WC)和纳米WC颗粒(part-WC).     

两种菁类染料复合敏化TiO_2纳米晶电极的光电化学研究

应用光电化学方法研究了两种菁类染料Cy3和Cy5复合敏化TiO2纳米晶电极的光电化学行为.结合两种染料的紫外-可见光谱和循环伏安曲线,确定了Cy3和Cy5的电子基态和激发态能级位置.结果表明两种染料的激发态能级位置能与TiO2纳米粒子导带边位置相匹配,复合敏化可以显著提高TiO2纳米晶的光电流,使TiO2纳米晶电极吸收波长由紫外光区红移至可见光区和近红外区.复合敏化降低了染料Cy3 在电极吸附时的聚集程度,使其单色光的转换效率(IPCE)提高了169%,复合敏化电极总的光电转换效率η为2.09%,分别是Cy3和Cy5单独敏化时光电转换效率的2.069 和1.229倍.     

两种菁类染料复合敏化TiO2纳米晶电极的光电化学研究

应用光电化学方法研究了两种菁类染料Cy3和Cy5复合敏化TiO2纳米晶电极的光电化学行为. 结合两种染料的紫外-可见光谱和循环伏安曲线, 确定了Cy3和Cy5的电子基态和激发态能级位置. 结果表明两种染料的激发态能级位置能与TiO2纳米粒子导带边位置相匹配, 复合敏化可以显著提高TiO2纳米晶的光电流, 使TiO2纳米晶电极吸收波长由紫外光区红移至可见光区和近红外区. 复合敏化降低了染料Cy3在电极吸附时的聚集程度, 使其单色光的转换效率(IPCE)提高了169%, 复合敏化电极总的光电转换效率η为2.09%, 分别是Cy3和Cy5单独敏化时光电转换效率的2.069和1.229倍.     

纳米TiO2混晶的形成及其对光催化性能的影响

用溶胶-凝胶法通过改变晶型调节剂2-甲基-2,4戊二醇的添加量制备了金红石相和锐钛矿相比例不同的纳米TiO2混晶.以膨胀珍珠岩为载体,制备珍珠岩负载纳米TiO2混晶催化剂,以X射线衍射(XRD)、紫外-可见吸收光谱(UV-visiblespectrum)、BET、Raman光谱等方法对纳米TiO2混晶和负载型纳米TiO2催化剂进行表征和性能测定,研究了催化剂的混晶效应对光催化降解甲基橙催化性能的影响.结果表明:晶型调节剂的含量及制备条件对混晶中金红石和锐钛矿相TiO2的比率有较大的影响.对于负载型纳米TiO2催化剂,混晶比影响催化剂的光催化降解效率,当混晶比为6.1时光催化效率最高,这一结果对光催化剂的制备和应用都具有重要的意义.     

N,N′-对羧苄基吲哚三菁敏化纳米TiO2电极的研究

应用光电化学方法研究了N, N′-对羧苄基吲哚三菁（Cy5）染料敏化TiO2纳米晶电极的光电化学行为,优化了敏化的条件.结合Cy5的循环伏安曲线和光吸收阈值,初步确定Cy5电子基态和激发态能级位置.结果表明,Cy5电子激发态能级位置能与TiO2纳米粒子导带边位置相匹配,因而使用该染料敏化可以显著提高TiO2纳米晶的光电流,使TiO2纳米晶电极吸收波长由紫外光区红移至可见光区和近红外区,光电转换效率得到明显改善,在膜厚为6.5μm、敏化时间为6 h的条件下IPCE值（incident photo-to-electricity conversion efficiency）最高可达46.4％,总的光电转换效率η为1.70％.     

TiO2/Ag2O纳米材料的制备及其对甲醛的气敏性能

采用溶胶-凝胶法制备了掺杂Ag的TiO2纳米晶粉体. 用XRD、TEM和BET方法对纳米晶的晶型﹑晶粒大小和表面性能进行了表征. 分析结果显示, 相同条件下掺杂Ag的TiO2比纯TiO2纳米材料具有更大的比表面积. 气敏性能测试结果表明, 掺杂Ag的TiO2传感器对甲醛有较好的灵敏度和更高的选择性.当焙烧温度为500 ℃, 掺杂Ag的摩尔比为5%(n(AgNO3)/n(Ti(OC4H9)4)=5%)时, TiO2对甲醛气体敏感性能最好. 在最佳工作电流124 mA下, 该元件对10 μL·L-1 HCHO的灵敏度S 接近4, 它的响应时间不超过1 s, 恢复时间为9 s.     

质子钛酸盐热解纳米TiO_2的光电性能

应用常温搅拌法合成质子钛酸盐,在不同的温度下煅烧生成TiO2纳米晶.X射线衍射、透射电镜、扫描电镜、紫外-可见光谱、光电压~电流和交流阻抗测试,表明500℃煅烧下制备的TiO2纳米晶表现出较好的光电性能,转换效率达到6.39%.     

TiO2纳米管与纳米线的制备及光电化学研究

利用钛箔表面沉积一层TiO2纳米粒子作为晶种,与NaOH反应,通过改变反应温度制备了TiO2纳米管与纳米线.在170℃,48 h的条件下合成了TiO2纳米管.在180℃时得到另一种一维的TiO2纳米线.并用XRD,SEM,SAED,EDS及HRTEM等分析手段对两种产物的成分、形貌、结构进行表征.对TiO2纳米管电极的光电化学性能进行了研究.结果表明,TiO2纳米管与纳米线为锐钛矿型和金红石型的混晶结构.TiO2纳米管单色光的光电转化效率达到10.38%.与钛酸盐纳米管相比,混晶结构TiO2纳米管显示出优良的光电转化性能.     

高效光催化活性钠米农药制剂的制备

采用钛酸丁酯水解法制备出直径约为20 nm的纳米TiO2,并用钛酸丁酯对其进行改性。研究表明TiO2与硬脂酸事实上通过化学键键合,由亲水性变为亲油性。文中还提出了三种制备TiO2复合纳米农药制剂的方案,并探讨了几种TiO2复合纳米农药制剂在不同条件下的光催化降解率。结果表明,采用钛酸丁酯为原料直接在农药乳油中原位生成的TiO2复合纳米农药制剂与原农药性状保持基本一致,光催化降解率最大。     

纳米二氧化硅复合悬浮液合成及聚合物吸附研究

从水玻璃合成了纳米硅溶胶,并以它为起始原核,通过水解钛酸正丁酯沉积二氧化钛,制得了稳定的二氧化钛复合二氧化硅纳米悬浮液,研究了添加的高分子两亲分散剂聚醚多胺在硅胶粒上的吸附和二氧化钛沉积过程中的贡献。研究结果表明,添加的聚醚多胺吸附在硅胶粒表面,有利于硅溶胶的稳定;钛酸正丁酯-丁醇-硫酸水解反应是可逆的,二氧化钛向硅胶粒定向沉积,这些沉积物呈无定形态,在沉积过程中,吸附的这些添加剂发生离子化,其阳离子端基形成的离子氛有利于二氧化钛沉积,并能减少胶粒粘接或团聚。     

Characterization of oxides obtained by heating a mixture of peroxoniobic acid and peroxotitanic acid

Nb-doped TiO(2) particles were prepared by heating a mixture of peroxotitanic acid and peroxoniobic acid in air. When the heating temperature was more than 1173 K, the dominant phase obtained was rutile TiO(2), along with a small amount of TiNb(2)O(7). The relationship between the lattice parameters of the obtained rutile TiO(2) depended on the molar fraction of Nb/(Ti + Nb). In the case where peroxo compounds were used as a precursor, a change in the lattice parameters of the rutile TiO(2) was observed within the lower X(Nb) range, as compared to the alkoxide method. The results indicate that a homogeneous dispersion of doped Nb(5+) ions in the obtained rutile TiO(2) lattice was achieved by using peroxo compounds. Furthermore, the oxide particles obtained by using peroxo compounds had a lower activation energy of the carrier electrons (E(a)) and oxygen vacancies, even though the heating procedure was carried out in air. The UV-vis absorption spectra and Raman spectra of the obtained oxide particles indicated that the dominant reaction of the decomposition of O(2)(2-) ions in the TiO(2) lattice was O(2)(2-)→ O(2) + 2e(-) as a reducing agent.     

活性碳载体对TiO2光催化降解Cl2CHCOOH性能的影响

研究了活性碳(AC)载体对TiO₂光催化降解Cl₂CHCOOH性能的影响.结果表明,加入AC载体能提高TiO₂的光催化反应速度,而且AC加入方法及含量有明显影响.本文探讨了TiO₂光催化性能提高的原因.     

The adsorption and reaction of a titanate coupling reagent on the surfaces of different nanoparticles in supercritical CO2

The adsorption and reaction in supercritical CO2 of the titanate coupling reagent NDZ-201 on the surfaces of seven metal oxide particles, SiO2, Al2O3, ZrO2, TiO2 (anatase), TiO2 (rutile), Fe2O3, and Fe3O4, was investigated. FTIR and TG analysis indicated that the adsorption and reaction were different on different particle surfaces. On SiO2 and Al2O3 particles, there was a chemical reaction of the titanate coupling reagent on the surfaces. On the surfaces of ZrO2 and TiO2 (anatase) particles, there were two kinds of adsorption, weak and strong adsorption. On the surfaces of TiO2 (rutile), Fe2O3, and Fe3O4 particles, there was only weak adsorption. The acidity or basicity of the OH groups on the particle surface was the key factor that determined if a surface reaction occurred. When the OH groups were acidic, the titanate coupling reagent reacted with these, but otherwise, there was no reaction. The surface density of OH groups on the original particles and the amount of titanate coupling reagent adsorbed and reacted were estimated from TG analysis. The reactivity of the surface OH groups of Al2O3 particles was higher than that of the SiO2 particles.     

Size-selective photocatalytic reactions by titanium(IV) oxide coated with a hollow silica shell in aqueous solutions

A novel core-shell composite photocatalyst, commercially available titanium(IV) oxide (TiO(2)) particles directly incorporated into a hollow amorphous silica shell, was fabricated by successive coating of TiO(2) with a carbon layer and a silica layer followed by heat treatment to remove the carbon layer. The composite induced efficient photocatalytic reactions when relatively small substrates were used, such as methanol dehydration and decomposition of acetic acid, without any reduction in the intrinsic activity of original TiO(2), but did not exhibit efficient photocatalytic activity for decomposition of large substrates, methylene blue and polyvinyl alcohol. The unique size-selective properties of the composites are due to their structural characteristics, i.e., the presence of a pore system and a void space in the silica shell and between the shell and medial TiO(2) particles, respectively. The loading of alkylsilyl groups on the surface of the composite led to highly photostable floatability: the floated sample also induced efficient photocatalytic reaction for decomposition of acetic acid while retaining floatation at the gas/water interface.     

SO_2在TiO_2颗粒物表面的非均相反应

使用漫反射红外傅里叶变换光谱(DRIFTS)原位反应器研究了SO2在TiO2颗粒物表面的非均相反应.研究了氧气浓度、相对湿度(RH)及紫外光光照对反应的影响.结果表明,SO2在TiO2颗粒物上可转化为亚硫酸盐或被氧化为硫酸盐.水汽或者紫外光照可促进SO2在TiO2颗粒物表面的非均相氧化反应,在两者都存在的情况下,对促进硫酸盐的生成有协同效应.在干态无光照条件下和一定湿度(RH=40%)紫外光照条件下,以硫酸盐的生成来计算,SO2在TiO2颗粒物表面的反应级数分别为二级和一级;反应摄取系数γBET分别为1.94×10-6和1.35×10-5.TiO2颗粒物表面的羟基参与了反应,在紫外光照下表面生成的活性氧物种在反应中起重要作用.     

Size control synthesis of sulfur doped titanium dioxide （anatase） nanoparticles, its optical property and its photo catalytic reactivity for CO2 ＋ H2O conversion and phenol degradation

Sulfur doped anatase TiO2 nanoparticles (3 nm−12 nm) were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles (24 nm). The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2+H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.     

Synthesis of Crystalline Nanosized Titanium Dioxide via a Reverse Micelle Method at Room Temperature

Crystalline TiO2 nanoparticles were synthesized by hydrolysis of titanium tetrabutoxide in the presence of hydrochloric acid in Np-5(lgepal CO-520)/ cyclohexane reverse micelle solution at room temperature.Pure rutile nanoparticles were obtained at an appropriate acid concentration.The influences of various reaction conditions such as the concentration of acids,water content value (2=[H2O]/[Np-5]) on the formation,erystal phase,morphology,and size of the TiO2 particles were investigated.     

Large-scale synthesis of TiO2 nanorods via nonhydrolytic sol-gel ester elimination reaction and their application to photocatalytic inactivation of E. coli

A simple method of synthesizing a large quantity of TiO(2) nanorods was developed. A nonhydrolytic sol-gel reaction between titanium(IV) isopropoxide and oleic acid at 270 degrees C generated 3.4 nm (diameter) x 38 nm (length) sized TiO(2) nanocrystals. The transmission electron microscopic image showed that the particles have a uniform diameter distribution. X-ray diffraction and selected-area electron diffraction patterns combined with high-resolution transmission electron microscopic image showed that the TiO(2) nanorods are highly crystalline anatase crystal structure grown along the [001] direction. The diameters of the TiO(2) nanorods were controlled by adding 1-hexadecylamine to the reaction mixture as a cosurfactant. TiO(2) nanorods with average sizes of 2.7 nm x 28 nm, 2.2 nm x 32 nm, and 2.0 nm x 39 nm were obtained using 1, 5, and 10 mmol of 1-hexadecylamine, respectively. The optical absorption spectrum of the TiO(2) nanorods exhibited that the band gap of the nanorods was 3.33 eV at room temperature, which is 130 meV larger than that of bulk anatase (3.2 eV), demonstrating the quantum confinement effect. Oleic acid coordinated on the nanorod surface was removed by the reduction of the carboxyl group of oleic acid, and the Brunauer-Emmett-Teller surface area of the resulting naked TiO(2) nanorods was 198 m(2)/g. The naked TiO(2) nanorods exhibited higher photocatalytic activity than the P-25 photocatalyst for the photocatalytic inactivation of E. coli.