含CexZr1-xO2三效催化剂设计的神经网络仿真与优化

提出一种含CexZr1-xO2的三效催化剂的设计方法,即利用人工神经网络来进行辅助设计.首先考察了影响三效催化剂性能的一些重要因素,确定了所研究的三效催化剂模型.然后采用共沉淀方法制备了一系列铈锆固溶体,并将它们作为三效催化剂的助催化剂.采用传统的催化剂制备方法制备了一系列负载贵金属的三效催化剂,所制备的催化剂在模拟尾气中进行评价,得到的数据作为神经网络的训练样本和测试样本,建立了神经网络模型,并初步进行了预测和优化.     

Ce-Zr-La-Al2O3的制备及负载的单Pd三效催化剂

采用共沉淀和浸渍两种方法制备了Ce-Zr-La-Al2O3(CZLA),对其进行了N2吸附和X射线衍射分析.以CZLA为载体制备了2%Pd/CZLA三效催化剂,并对催化剂进行了程序升温还原和活性测试.结果表明,两种方法制备的CZLA均具有较好的结构、织构和储氧性能,共沉淀法制备的CZLA具有更好的抗老化性能.以CZLA为载体所制备的单Pd三效催化剂表现出低的起燃温度、优异的三效性能,特别是优异的转化NO性能及抗老化性能.     

从钯纳米溶胶出发制备Pd/Ce0.6Zr0.4-xYxO2纳米三效催化剂

从Pd纳米粒子溶胶出发,采用一步沉淀法和浸渍法分别制备了0.5%(质量分数)Pd/Ce0.6Zr0.4-x Y x O2(x=0,0.03,0.05,0.1)负载型三效催化剂,考察了贵金属纳米粒子的负载方法以及Y的掺杂量对三效催化活性和水热稳定性的影响。结果表明,和浸渍法制备的催化剂相比,采用一步沉淀法制备的催化剂具有更高的三效催化活性。对于一步沉淀法制备的催化剂,Y的掺杂量对新鲜样品的三效催化活性影响不大,然而,900℃水热老化后,Y的掺杂量为0.05的Pd/Ce0.6Zr0.35Y0.05O2催化剂表现出最佳的催化活性,且其三效窗口也最为稳定。以上研究结果表明,一步沉淀法是一种从贵金属纳米溶胶出发制备纳米三效催化剂的有效方法,且在铈锆储氧材料中掺杂适量的Y元素可以进一步提高催化剂的三效催化活性和水热稳定性。     

Ce_(0.67)Zr_(0.33)O_2材料的制备和表征及其负载单Pd三效催化剂的性能

采用共沉淀法、均匀沉淀法、微乳法和水热法四种方法制备了铈锆固溶体(CZ),对其进行了X射线衍射和N2吸附脱附分析.以CZ为载体制备了负载单Pd三效催化剂,并对催化剂进行了氧化还原性能测试.结果表明,制备方法对CZ载体的物理、化学性能有显著的影响,而其负载单Pd催化剂的催化活性与CZ载体比表面积的大小没有明显的对应关系.采用共沉淀法制备的CZ载体具有相对良好的热稳定性以及储放氧能力,其负载单Pd催化剂在老化前后表面PdO物种有良好的还原性能,并表现出优异的三效催化性能.     

(Ce-Zr-Pr)O2在三效催化剂中的应用

采用共沉淀方法制备了(Ce-Zr-Pr)O2样品,利用XRD,BET对样品进行了表征,并将样品用于三效催化剂的制备,利用实验室配气装置模拟尾气条件,对催化剂性能进行了评价.结果表明,(Ce-Zr-Pr)O2具有立方萤石结构,耐热稳定性较好,所制备的催化剂具有更好的氧化还原活性,表现为起燃温度较低,NOx的净化效率较高.     

负载型Pd三效催化剂：载体CeO2-ZrO2-BaO的制备及催化性能

制备了不同BaO含量的CeO2-ZrO2储氧材料,并以此材料为载体浸渍H2PdCl6制得三效催化剂.结果表明,不论新鲜还是1 000 ℃老化状态下,以10%BaO添加CeO2-ZrO2储氧材料制备的Pd三效催化剂活性最佳,起燃和完全转化温度最低.XPS结果证实,10%BaO添加.通过稳定PdO活性组分并改变其电子环境使得催化剂有最佳活性.而随着BaO含量持续增加,Pd活件组分相对处于较氧化状态.储氧量、低温N2吸附-脱附测试以及XRD测试结果均表明10%BaO添加的材料储氧量,比表面积以及孔容均最大,而且有适应三效催化的孔径.这些结果均有助于以其制备的Pd三效催化剂获得更好的活性以及热稳定性.     

高性能Ce_(0.5)Zr_(0.5)O_2稀土储氧材料的制备及其负载的单Pd三效催化剂

以碳酸铵水溶液为沉淀剂,改变前驱体盐溶液的浓度,采用共沉淀法制得了一系列Ce0.5Zr0.5O2固溶体材料.以此系列材料为载体制备了负载型单Pd三效催化剂,并利用N2吸附-脱附、X射线衍射、储氧量测定和程序升温还原等技术对材料了进行表征.结果表明,所制Ce0.5Zr0.5O2材料具有优异的抗高温老化性能和氧化还原性能,且盐溶液的浓度对材料及其负载型Pd三效催化剂性能的影响较大.当盐溶液浓度为0.3mol/L时,制备材料的织构性能最佳,经1000oC老化5h后其比表面积和孔体积分别为53.0m2/g和0.17cm3/g.所制得的三效催化剂对CO,NO和C3H8具有低的起燃温度和完全转化温度,表现出最佳的催化性能,具有良好的应用前景.     

纳米氧化铈的制备及其催化性能的研究

采用两种方法制备了纳米氧化铈材料, 通过X射线衍射分析(XRD), 透射电子显微镜(TEM), 表面吸附(BET)等手段对样品的物化性能进行了表征, 并对纳米氧化铈在三效催化剂中的应用进行了探讨, 通过催化反应试验对其催化性能进行了评价. 结果表明, 制备的样品具有纳米尺度的粒径, 热耐热稳定性好, 高温老化后晶相稳定, 在三效催化剂中应用时, 能有效改善三效催化剂的起燃特性, 催化性能较之普通氧化铈材料有明显提高.     

Rh-Au/γ-Al2O3 三效纳米催化剂的制备与表征

采用超声辅助膜扩散还原法 (UAMR) 和等体积浸渍法 (IMP) 制备了 Rh/γ-Al2O3 和 Rh-Au/γ-Al2O3 催化剂, 考察了它们的三效模型反应 (CO+O2, C3H8+O2, CO+NO 和 C3H6+NO+O2) 活性. H2-O2 滴定和透射电镜结果表明, UAMR 法制得的 Rh/γ-Al2O3 和 Rh-Au/γ-Al2O3 催化剂的金属分散度分别为 45.3% 和 40.1%, 金属粒子表面积分别为 199.6 和 133.0 m2/g, 金属粒子平均粒径小于 3 nm. 对于三效模型反应, 与 IMP 法制备的催化剂相比, UAMR 法制备的 Rh/γ-Al2O3 和 Rh-Au/γ-Al2O3 具有更高的初始活性, 其中后者的活性也高于或接近于 IMP 法制备的 Rh/γ-Al2O3 催化剂. 催化剂经高温老化处理后, 活性均有所下降. UAMR 是一种新颖的负载型纳米催化剂的制备方法, 具有潜在的应用前景.     

CeO2-ZrO2-Y2O3对Pt-Rh型三效催化剂性能的影响

采用共沉淀法技术制备了Ce0.35Zr0.55Y0.10固溶体,并对其进行了比表面积、储氧量的测试和XRD的表征.将其用于低贵金属Pt-Rh型三效催化剂的制备,考察了CeO2-ZrO2-Y2O3对三效催化剂性能的影响.结果表明,Ce0.35Zr0.55Y0.10具有与Ce0.50Zr0.50O2相似的立方结构和相近的储氧量,经高温(1000 ℃)后仍能保持较大的比表面积(38.66 m2·g-1).和含Ce0.50Zr0.50O2的三效催化剂相比,含CeO2-ZrO2-Y2O3的三效催化剂经高温老化后,C3H8,CO,NO仍具有较高的转化率和较低的起燃温度.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Separation of Tl/III/ from Tl/I/

A method for the separation of Tl/III/from Tl/I/ is reported employing 1-/2-pyridylazo/-2-naphthol /PAN/ and Rhodamine-B as extracting agents.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.     

Analysis of nonvalent interactions in the crystals of conformational polymorphs of the composition CaHbNcOdSe by means of molecular voronoi-dirichlet polyhedra

Nonvalent interactions in crystals of compounds of the composition C _a H _b N _c O _d S _e that exhibit conformational polymorphism and have no fewer than four structurally characterized modifications are analyzed using molecular Voronoi-Dirichlet polyhedrals. A unique combination of the types of occurring intra- and intermolecular nonvalent contacts is shown to correspond to each conformational polymorph. Nonvalent interactions involving hydrogen atoms are found to occur most often in crystal structures, and least often those involving S, N, and O atoms.     

橙红色荧光粉Ca_(1-x-y)Sm_xBi_ySiO_3的制备及其发光性能

以Sm3+作为激活剂,Bi3+作为辅助激活剂,采用水热法合成Ca1-x-ySmxBiySi O3前驱体,然后在1 100℃焙烧得到系列橙红色荧光粉。用X-射线衍射仪、扫描电镜和荧光分光光度计和傅里叶变换红外光谱等手段对样品的组成、结构和形貌及其发光性质进行分析和表征。分析结果表明:产物都为三斜晶系结构的Ca1-x-ySmxBiySi O3和四方结构的方石英Si O2共熔体。在405 nm近紫外光激发下,产物的发射光谱由3个峰组成,发射峰值位于566、606和650 nm处,分别归属于Sm3+的4G5/2→6HJ/2(J=5,7,9)跃迁。产物的激发光谱在405 nm有很强的发射带,与近紫外LED芯片匹配。随着Sm3+掺量的增加,样品发光强度先增强后减弱,当Sm3+的物质的量分数为3%时发光强度达到最大,浓度猝灭机理为电偶极-电偶极相互作用。当Bi3+的物质的量分数在0.3%~1.5%时,对产物Ca0.97Sm0.03Si O3的荧光强度起敏化作用。Sm3+和Bi3+的最佳物质的量分数分别为3%和0.5%。     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Rate of reactions between D2O and CaxAlyOz

The rate of the reaction between D₂O and the calcium aluminum oxides Ca₃Al₂O₆, Ca₅Al₆O₁₄, CaAl₂O₄, and CaAl₄O₇ was investigated by on-line neutron diffraction powder methods at temperatures from room temperature to 100°C. The rate of the reaction increases with increasing calcium content of the compounds and with increasing temperature for each of the compounds. The crystallographic stable hydrate Ca₃Al₂(OD)₁₂ is obtained from CaAl₄O₇ and CaAl₂O₄ at temperatures above 63°C, from Ca₅Al₆O₁₄ at temperatures above 49°C, and from Ca₃Al₂O₆ at temperatures as low as 7°C.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.