黄豆黄素纯度标准物质研制

建立黄豆黄素纯度标准物质的研制方法。选择纯度大于98%（质量分数）的黄豆黄素标准品作为标准物质候选物,通过加热和冷冻干燥去除多余的水分。通过红外、质谱、核磁氢谱进行结构确证和表征后分装,采用质量平衡法进行均匀性和稳定性检验。结果显示,标准物质均匀性良好,在常温条件下保存12个月稳定;采用质量平衡法和定量核磁法进行纯度定值,质量平衡法的定值结果为99.09%,定量核磁法的定值结果为99.13%,取平均值99.1%作为最终定值结果;对定值、均匀性和稳定性引入的不确定度进行了系统评定,扩展不确定度为0.3%(k=2)。研制的黄豆黄素纯度标准物质已申报国家一级标准物质,编号为GBW 10171。该标准物质可用于食品、保健品、饲料中黄豆黄素含量检测。     

甲醇中丙烯酸乙酯溶液标准物质制备

研制特征量值为1 000μg/mL甲醇中丙烯酸乙酯溶液标准物质。分别利用气相色谱-质谱联用法、核磁共振波谱法和红外光谱法对丙烯酸乙酯标准品原料进行定性确认。采用质量平衡法对主成分含量进行量值核验，丙烯酸乙酯标准品纯度（质量分数）为99.842%，扩展不确定度为0.3%，量值在证书给出的不确定度范围内，因此采用证书标识量值作为原料标准值，证书中标识的不确定度作为原料不确定度。以丙烯酸乙酯标准品为原料，采用重量-容量法制备溶液标准物质，分别采用F检验和t检验对标准物质进行均匀性和稳定性检验，并对其定值结果的不确定度进行评定。结果表明，该标准物质均匀性和稳定性良好，有效期为12月，定值结果的相对扩展不确定度为2%(k=2)，可用于环境样品中丙烯酸乙酯分析方法的确认和评价以及仪器校准与检测质量控制。     

低温封接玻璃成分分析标准物质的研制

研制了低温封接玻璃成分分析标准物质,对标准物质的制备技术进行了研究。分别用F检验和t检验法对研制的标准物质进行了均匀性和稳定性检验,结果表明,研制的低温封接玻璃标准物质具有良好的均匀性和稳定性。采用6家实验室进行协作定值,对定值结果的不确定度进行了评定。各组分定值结果的相对扩展不确定度均小于5%(k=2)。     

牛磺酸标准物质的研制

研制了牛磺酸标准物质。采用红外光谱(IR)法对牛磺酸进行定性,经均匀性初检后分装成200瓶样品,利用超高效液相色谱(UPLC)及高效毛细管电泳(HPCE)两种不同原理的方法进行定值,从样品中随机抽取15瓶采用超高效液相色谱(UPLC)法进行了均匀性检验,经F检验表明在95%的置信区间范围内样品均匀性良好,稳定性考察按照短期稳定性(1个月)和长期稳定性(12个月)分别进行,结果表明在考察期间样品稳定性良好。评定了定值结果的不确定度,牛磺酸标准物质定值结果为99.6%,相对扩展不确定度为0.5%(k=2)。     

空气中偏二甲肼气体标准物质的研制

采用称量法制备空气中偏二甲肼气体标准物质,分别用F检验和回归曲线法对研制的标准物质进行均匀性和稳定性检验。结果表明,研制的空气中偏二甲肼气体标准物质具有良好的均匀性和稳定性,定值结果分别为10,500μmol/mol,定值结果的相对扩展不确定度为2%(k=2)。该标准物质可用于偏二甲肼报警器的检定或校准。     

宝藿苷Ⅰ纯度标准物质的研制

以淫羊藿提取物为原料,通过正相硅胶柱色谱和凝胶柱色谱等分离纯化手段,研制了宝藿苷Ι纯度标准物质。采用液相色谱–质谱法和核磁共振技术对宝藿苷Ⅰ纯度标准物质进行定性鉴定,利用高效液相色谱(HPLC)法和胶束电动毛细管色谱(MECC)法对宝藿苷Ι的纯度进行定值分析,同时利用HPLC法对宝藿苷Ι纯度标准物质进行均匀性检验与稳定性考察,通过F检验和t检验法对其均匀性进行检验,表明瓶间和瓶内均匀性一致,12个月稳定性检验结果的相对标准偏差为0.02%,说明宝藿苷Ι纯度标准物质是稳定的。对定值结果的不确定度进行了评价,研制的宝藿苷Ι纯度标准物质的定值结果和扩展不确定度分别为99.7%和0.3%(k=2)。     

甲醇中溴苯标准样品的研制

介绍甲醇中溴苯标准样品的研制方法.标准样品采用称量法制备,气相色谱-质谱法进行均匀性和稳定性检验,以配制值为标准值,并对其不确定度进行分析评定.结果表明,甲醇中溴苯标准样品的均匀性良好,至少在24个月内是稳定的,可用于环境监测分析.     

液相色谱仪检定用甲醇中胆固醇标准物质的研制

采用重量–容量法制备了液相色谱检定用200μg/m L的甲醇中胆固醇标准物质,分别用F检验和回归曲线法对研制的标准物质进行了均匀性和稳定性检验,对定值结果的不确定度进行了评定。结果表明,研制的甲醇中胆固醇标准物质具有良好的均匀性和稳定性,定值结果的相对扩展不确定度为2%(k=2)。该标准物质可用于液相色谱仪示差折光检测器、蒸发光散射检测器的检定。     

甲基苯丙胺标准物质的定值与不确定度分析

为了建立法庭科学毒品检测量值溯源体系,研制了甲基苯丙胺纯度标准物质。通过红外光谱、质谱法对甲基苯丙胺样品进行定性分析,优化并建立了高效液相色谱(HPLC)、差示扫描量热法(DSC)两种定值分析方法。采用热重分析法和电感耦合等离子体质谱法测定水分和无机离子的含量。通过均匀性与稳定性检验结果表明,甲基苯丙胺标准物质的均匀性良好,稳定性至少1年,同时对其进行了不确定度评定。研制的甲基苯丙胺标准物质的纯度为99.8%,扩展不确定度为0.2%(k=2)。     

水污染监测用水合肼标准样品的制备与量值评价

研制了水污染监测用水合肼标准样品。介绍了试剂的验证、均匀性和稳定性检验、分析定值和测定数据的统计检验等研制方法。采用重量法制备,用国家标准分析方法对样品进行均匀性和稳定性研究;并进行不确定度评估;水合肼标准样品的均匀性良好,至少可稳定30个月以上;标准值为50.0μg/L,相对扩展不确定度为2.2%(k=2)。     

A methodology for choosing parameters for ESR readout of alanine dosimeters for radiotherapy

Spectrometer settings for ESR readout of alanine dosimeters for radiotherapy have been investigated. Several ESR parameters were studied and determined. The main reason for this work is to choose the suitable parameters to increase signal-to-noise ratio and to reduce the uncertainty on ESR readout, which is one of the main components of uncertainty of alanine/ESR dosimetry system for radiotherapy. The new spectrometer settings have been applied for ESR readout of alanine dosimeters irradiated from 1 to 10 Gy. A higher signal-to-noise ratio has been achieved compared to our old spectrometer settings. The extended uncertainty (k=2) has been evaluated in the dose range 2–10 Gy (maximum uncertainty of 4.9% for 2 Gy, while minimum uncertainty of 1.4% for 10 Gy), which implies that the alanine/ESR dosimetry system can be applied to radiotherapy dose level that needs a global accuracy of 5%.     

Prospects for development of a technology for production of butene-1

Industrial technologies for production of butene-1 are described, including the most promising process for recovery of butene-1 of polymerization purity from C₄ fractions formed in pyrolysis and catalytic cracking of hydrocarbons. It is shown that this technology can be improved and suggested to use as a raw material the recycle butene fraction formed from these C₄ fractions upon isolation of 1,3-butadiene and isobutene. A technological scheme for recovery of butene-1 of polymerization purity is suggested.     

Preparation of PVA membrane for immobilization of GOD for glucose biosensor

A membrane was prepared using polyvinyl alcohol (PVA) with low and high degree of polymerization (DOP), acetone, benzoic acid (BA) and was cross-linked by UV treatment. Membrane composition was optimized on the basis of swelling index. Membrane prepared with 12% low DOP and 8% high DOP of PVA, 2% BA, dissolved in buffer containing 20% acetone and cross-linked with UV treatment exhibited lower swelling index. Fourier transform infrared (FTIR) study of the membranes showed appearance of a strong band at approximately 2337 cm(-1) when UV was used for cross-linking in the presence of benzoic acid. Scanning electron microscope (SEM) study revealed that membrane cross-linked with UV treatment was smoother. Glucose oxidase (GOD)-PVA membrane was associated with the dissolved oxygen (DO) probe for biosensor reading. Glucose was detected on the basis of depletion of oxygen, when immobilized GOD oxidizes glucose to gluconolactone. A wide detection range, 0.9-225 mg/dl was estimated from the linear range of calibration plot of biosensor reading. Membranes were reused for 32 reactions without significant loss of activity and stored for 30 days (approximately 90% activity) at 4 degrees C. Membranes were also used with real blood samples.     

Potential of FTIR spectroscopy for analysis of tears for diagnosis purposes

It has been widely reported that the tear film, which is crucially important as a protective barrier of the eye, undergoes biochemical changes as a result of a wide range of ocular pathology. This tends to suggest the possibility of early detection of ocular diseases on the basis of biochemical analysis of tears. However, studies of tears by conventional methods of biomolecular and biochemical analysis are often limited by methodological difficulties. Moreover, such analysis could not be applied in the clinic, where structural and morphological analyses by, mainly, slit-lamp biomicroscopy remains the recommended method. In this study, we assessed, for the first time, the potential of FTIR spectroscopy combined with advanced chemometric processing of spectral data for analysis of raw tears for diagnosis purposes. We first optimized sampling and spectral acquisition (tears collection method, tear sample volume, and preservation of the samples) for accurate spectral measurement. On the basis of the results, we focused our study on the possibility of discriminating tears from normal individuals from those of patients with different ocular pathologies, and showed that the most discriminating spectral range is that corresponding to variations of CH₂ and CH₃ of lipid aliphatic chains. We also report more subtle discrimination of tears from patients with keratoconus and those from patients with non-specific inflammatory ocular diseases, on the basis of variations in spectral ranges attributed notably to lipid and carbohydrate vibrations. Finally, we also succeeded in distinguishing tears from patients with early-stage and late-stage keratoconus on the basis of spectral features attributed to protein structure. Therefore, this study strongly suggests that FTIR spectral analysis of tears could be developed as a valuable and cost-saving tool for biochemical-based detection of ocular diseases, potentially before the appearance of the first morphological signs of diseases. Combined with supervised modelling methods and with use of a spectral data base acquired for representative patients, such a spectral approach could be a useful addition to current methods of clinical analysis for improvement of patient care.

Application of thermal analysis for investigations of polymer powders for coatings

Polypropylene coatings obtained by the fluidized bed method were investigated. It was proved that the application of thermal analysis methods for their characterization gave many useful data, as a consequence of the similar conditions of thermal measurements and plastics powder processing. Significant correlations were found between the thermal properties and the standard coating poperties.

---

Zusammenfassung Durch Fluidisationsverfahren erhaltene Polypropylenbeschichtungen wurden untersucht. Es wurde festgestellt, daß infolge der ähnlichen Bedingungen von thermischen Messungen und Plastpulverisierungsverfahren die Anwendung von thermischen Untersuchungsmethoden zu deren Charakterisierung viele nützliche Angaben liefern. Es konnten eindeutige Beziehungen zwischen thermischen Eigenschaften und Standardbeschichtigungseigenschaften gefunden werden.

---

, . , , . .

     

New method for prefractionation of plasma for proteomic analysis

The depth of proteome analysis is severely limited in complex samples with a wide dynamic range of protein abundance such as plasma. Removal of high‐abundance proteins should reveal the signal of lower abundance plasma proteins. However, smaller proteins may be part of larger protein complexes and hence the removal of proteins involved in complexes with high‐abundance proteins such as albumin may inhibit the search for disease biomarkers. Prefractionation of a sample divides it into fractions of reduced complexity, allowing improved detection of lower abundance proteins. Using a prefractionation device, which employs Gradiflow? technology, we were able to separate small volume plasma samples into multiple fractions based on the molecular weight and/or charge. The resulting samples of reduced complexity were directly compatible with 2‐DE. The use of this prefractionation machine may therefore be useful in the hunt for disease biomarkers.     

Adhesives for assembly procedures for products of radioelectronic industry

A list of adhesive materials, sealants, and potting compounds used at the enterprise is given. The basic properties of these materials are discussed, and particular process procedures in which they are employed are described.     

Piperazine-based buffers for liposome coating of capillaries for electrophoresis

Anionic liposomes can be coated on fused-silica capillaries for electrophoresis in the presence of N-(hydroxyethyl)piperazine-N'-(2-ethanesulfonic acid) (HEPES) as background electrolyte (BGE) solution. In this work, the interaction of various compounds with zwitterionic and anionic phospholipid coatings was studied with HEPES at pH 7.4 as BGE solution. The chromatographic and electrophoretic behavior of three test sample solutions (anionic, cationic, and neutral) was investigated for evaluation of the phospholipid coatings. Our results show that hydrophobic interactions between analytes and the phospholipid coating are important for the migration of charged analytes. In addition, the performances of other piperazine-based buffers, i.e., N-(2-hydroxyethyl)piperazine-N'-(2-hydroxypropanesulfonic acid), piperazine-N,N'-bis(2-ethanesulfonic acid), and piperazine-N,N'-bis(hydroxypropane sulfonic acid), at pH 7.4, as liposome solvent and BGE solution were evaluated and compared with the performance of HEPES at pH 7.4. The anionic liposome solution comprised 80/20 mol% phosphatidylcholine/phosphatidylserine. A simple test solution was selected and the chromatographic and electrophoretic migration behavior of the analytes was evaluated. The results show that, in addition to HEPES, other piperazine-based buffers at pH 7.4 are suitable for coating of fused-silica capillaries with anionic liposomes.     

Prospects for the use of fluidized-bed devices for production of coatings

It is shown that, currently, the most effective grinding and dispersant equipment in the technology of coating production are fluidized-bed devices—devices in which grinding and dispersion of pigments and fillers occur via ferromagnetic bodies driven by an electromagnetic field.     

缓冲溶液pH计算公式的推导

酸碱缓冲溶液在分析化学中的应用是多方面的 ,因此酸碱缓冲溶液 ｐＨ的计算是分析化学中必不可少的一个内容。目前 ,高师院校的分析化学多采用华中师范大学等校编的《分析化学》(第 2版 ) ,笔者在几年的教学中 ,发现该教材在缓冲溶液 ｐＨ计算的公式推导中存在疏漏。为此 ,在比较其他教材中该章节的内容后 ,从酸碱平衡最本质的内容ＰＢＥ出发 ,提出一种新的缓冲溶液ｐＨ计算公式推导方法。1　华中师范大学版教材中的问题[1]　　以一元弱酸及其共轭碱体系进行讨论 ,设弱酸ＨＡ浓度为ｃａ,共轭碱ＮａＡ浓度为ｃｂ。将ＨＡ Ａ-体系以Ｈ2 Ｏ作媒…