应用等离子体溅射方法制备钯-银合金复合膜及其膜表征

研究应用等离子体溅射方法制备钯 银合金复合膜 ,并用电子显微镜和高温气体渗透测定来表征膜的质量 .用sol gel方法在工业微滤氧化铝陶瓷膜上沉积纳米孔γ Al2 O3 膜 ,以改善衬底表面的粗糙度 ,降低气相沉积过程中的阴影效应 .以改进钯 银合金膜的气密性为目标来优化等离子体溅射方法的沉积条件 (衬底温度及沉积压力等 ) .典型的钯 银合金复合膜具有氢渗透速率 :0 .0 36× 10 -5 ～ 1.17× 10 -5cm3 /cm2 ·s·Pa ,氢对氮的分离选择性 :5 1.5～ 10 0 0 ,测试条件 :温度为 35 0～ 45 0℃ ,膜两侧压力降为 10 4～ 10 5 Pa     

陶瓷基钯银合金膜制备技术及性能研究

报道采用浆料涂敷与化学镀相结合法在陶瓷支撑上沉积钯银合金膜,采用浆料涂敷法,将含钯银的浆料涂敷在支撑体上,干燥后热分解,使支撑体表面沉积部分钯银。然后,采用化学镀在50℃下沉积钯银膜,热处理后,得到表面较光洁、厚度约为3μm、银含量为23%(原子百分含量)、合金化较完全的钯银合金膜,该膜在压差为0.1MPa,温度为300℃时的渗氢通量达45cm^3(STP)/(cm^2·min),分离因子达500,研究了钯银合金膜中银含量随热处理温度的变化规律,由实验结果发现,银逐渐向表面扩散,并在一定的温度条件达到基本平衡。     

陶瓷基钯银合金膜制备技术及性能研究

报道采用浆料涂敷与化学镀相结合法在陶瓷支撑上沉积钯银合金膜,采用浆料涂敷法,将含钯银的浆料涂敷在支撑体上,干燥后热分解,使支撑体表面沉积部分钯银。然后,采用化学镀在50℃下沉积钯银膜,热处理后,得到表面较光洁、厚度约为3μm、银含量为23%(原子百分含量)、合金化较完全的钯银合金膜,该膜在压差为0.1MPa,温度为300℃时的渗氢通量达45cm^3(STP)/(cm^2·min),分离因子达500,研究了钯银合金膜中银含量随热处理温度的变化规律,由实验结果发现,银逐渐向表面扩散,并在一定的温度条件达到基本平衡。     

Pd-Y合金膜的MOCVD研制

采用金属有机化合物的化学气相淀积法,以β-二酮螯合物为源物质,在多孔Al₂O₃衬底上成功制备了超薄钯钇合金膜.用Pd(AcAc)₂+Y(AcAc)₃混合源制备的钯钇合金膜的晶粒尺寸(21nm×10nm)比单独用Pd(AcAc)₂制备的钯膜的尺寸(30nm×10nm)小.XPS研究发现,制备的Pd-Y合金膜中Y/Pd比小于源物质的.氢的透气性实验表明,合金膜的氢渗透率高于Pd膜,且在200～350℃范围内渗透率稳定.     

表面改性SUS316L不锈钢的电化学行为研究

分别以表面镀Rh,表面离子束增强沉积Ta2O5膜及溶胶凝胶法沉积TiO2膜对冠状动脉支架用材料SUS316L不锈钢进行表面改性.采用电化学方法研究了该表面改性试样在Tyrode's模拟人工体液中的电化学行为.结果表明,上述3种表面改性方法均可提高SUS316L不锈钢在模拟人工体液中的阳极极化性能.其中对于采用离子束增强法沉积的Ta2O5膜和溶胶凝胶法沉积的TiO2膜,因Ta和Ti上的d轨道空位已被氧的电子占据,不利于氢吸附,从而抑制了阴极的析氢过程.X射线衍射分析发现,3种改性方法在SUS316L不锈钢表面依次形成均匀而致密的Rh金属层,Ta2O5的无序膜层和TiO2晶态膜层,阻止了合金元素的溶解,改善不锈钢的电化学性能.     

液相放电法合成氮化碳晶体

自从 Cohen等 [1,2 ] 预言了一种碳氮化合物 ( β- C3N4 )可能具有比金刚石还高的硬度和其它优异的力学、电学和光学性能以来 ,人们竟相采用各种技术手段 (如化学气相沉积、磁控溅射、离子束沉积和激光刻蚀等 )尝试合成这种新材料 [3,4 ] .但是 ,大多数合成的氮化碳材料为非晶或者是少量的晶体包埋在非晶的碳和 CNx 材料中 ,尚未制得可以精确地研究其晶体结构的足够大的单晶 .1 999年 ,Fu等 [5] 将液相电沉积技术应用于氮化碳材料的合成 ,从乙腈中沉积了氮含量为 2 5 %的氮化碳薄膜 .目前电化学沉积法制备的氮化碳薄膜多为非晶膜 [6～ 9]…     

Er-Bi合金膜在有机溶剂中的电沉积研究

利用循环伏安法和恒电位电解法探讨了室温条件下在二甲基亚砜(DMSO)中Er-Bi合金膜的电化学制备.研究了沉积电位、电流密度以及主盐浓度比对沉积膜质量的影响.实验结果表明,在ErCl3-Bi(NO3)3-LiCl-DMSO体系中,当控制恰当的体系组成和沉积条件,均可得到表面均匀、附着力强、有金属光泽的灰黑色非晶态Er-Bi合金膜,其中稀土Er的质量分数可达24.09％～46.56％.通过SEM、EDS分析得到沉积膜表面形貌和组成,通过XRD和DSC确定了合金膜的物相组成.结果表明,当所制备的合金膜在723 K进行热处理1 h后,可形成稳定的Er-Bi合金相.     

在有机溶剂中Eu-Co-Ni合金薄膜的电化学制备

利用恒电位沉积、循环电位沉积和脉冲电沉积法在DMSO体系中在铜基体上探讨了Eu-Co-Ni合金薄膜的制备.实验结果表明,在0.10mol/LEuCl3-0.10mol/L CoCl2-0.10mol/L NiCl2-0.1 0mol/l LiClO4-DMSO体系中,恒电位沉积技术制备出的Eu-Co-Ni合金膜表面较为粗糙,其中Eu含量为5.46～6.01 wt%,脉冲电沉积技术制备的Eu-Co-Ni合金膜表面平整,致密,附着力好,且有金属光泽,其中Eu含量为6.76%,循环电位扫描技术制备的Eu-Co-Ni合金膜表面平整,致密,附着力好,其中Eu含量为12.43%.通过XRD证明所得的合金薄膜为非晶态.     

脉冲激光沉积纳米NiO薄膜

Na Cl型 Ni O是一种 p型半导体 ,广泛用于传感器、催化剂、涂料、磁性材料及电极材料等领域[1～ 5] .最近 ,Poizot等 [6] 又报道了 Ni O可作为锂离子电池的阳极材料 ,使 Ni O成为又一新的研究热点 .纳米 Ni O粉末的制备方法有多种 ,主要包括化学沉淀法和沉淀转换法 ,Ni O薄膜的制备主要采用磁控溅射、化学气相沉积和电沉积等方法 [7～ 12 ] .脉冲激光沉积法具有操作简单和成膜纯净等优点 ,因此是制备薄膜的重要方法之一 .本文采用脉冲激光沉积 (PLD)法在氧气氛中使用金属镍作为靶材料 ,不锈钢作为基片 ,对 Ni O薄膜的制备进行了研究…     

热处理对SILAR法制备CuInSe_2薄膜性能的影响

0引言铜铟硒(CIS)具有合适的带隙、高光吸收系数、适当的电荷密度和迁移率,是一种用于薄膜太阳能电池的备受关注的吸收材料[1]。目前CuInSe2薄膜已采用多种方法进行制备,如金属前驱体硒化法[2]、共沉积法[3]、溅射法[4]、电沉积法[5]和化学气相沉积法[6]等。这些方法都有各自的     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.