高铝MAP沸石的非自发结晶动力学研究

在强碱性水溶液体系中,以水玻璃为硅源,以铝酸钠为铝源,在类质同晶高硅P沸石晶种导向作用下,反应物中自发生成的A型沸石可转晶为纯相高铝MAP沸石。升高反应温度有利于提高产物的结晶度。由不同温度下的晶化曲线计算出MAP沸石表观生长活化能为59.6kJ.mol^-^1。不用晶种时,同一反应物体系结晶产物为单一的A型沸石。在该反应物体系中,A型沸石的成核活化能与生长活化能分别为40.3和50.7kJ.mol^-^1。MAP高的生长活化能以及A型沸石相对低的成核与生长活化能揭示合成MAP沸石时使用晶种的原因。     

碱源对低模硅比凝胶水热合成β沸石的影响

以四乙基氢氧化铵为模板剂,研究了低模硅比条件下β沸石的合成规律.发现晶种和模板剂之间存在明显的协同导向作用.但碱源对晶种和模板剂的导向作用以及β沸石产物有明显影响.以NaOH为碱源时,晶种的作用主要是缩短晶化诱导期,而模板剂的作用主要是提高晶体生长速率.以氨水为碱源时,晶种和模板剂对缩短诱导期和提高晶体生长速率都有贡献.总的来说,以NaOH为碱源时凝胶的晶化速率较快.但是β沸石产物的硅铝比很低,且晶粒度较大,团聚体比较紧密.相比之下,以氨水为碱源有利于提高β沸石的硅铝比.同时,所合成的β沸石晶粒度小,外表面积大,团聚体中介孔较多.     

合成TS-1分子筛的结晶动力学及催化性能研究

 以自制的四丙基氢氧化铵为模板剂，通过改进经典的水热晶化操作步骤，快速合成出TS－1分子筛，并对其合成过程进行了结晶动力学研究．结果表明，在所考察的晶化温度下，TS－1的成核诱导期均很短，且晶体的成核及生长速率随晶化温度的升高而增大；其表观成核活化能和表观生长活化能分别为33．60和36．73kJ／mol，比经典的水热合成体系所得数值略小．晶化温度越高，晶化液的pH值变化越显著；分子筛结构的迅速形成与晶化液pH值的快速上升过程相一致．高温下合成的TS－1分子筛对苯酚羟基化反应的催化活性更高．导致TS－1分子筛催化活性差异的主要原因是进入分子筛骨架中钛的含量不同，以及样品的结晶度不同．在不同晶化温度下所合成的TS－1分子筛颗粒尺寸稍有差别，但均为100nm左右．     

四乙基溴化铵-氟化物复合模板剂合成β沸石 Ⅲ.结晶动力学及其影响因素

 考察了用四乙基溴化铵－氟化钠复合模板剂合成β沸石的结晶动\r\n力学．结果表明：其晶化曲线为典型的S形曲线；成核活化能En＝65．\r\n79kJ／mol，生长活化能Ec＝91．49kJ／mol；与单纯的四乙基溴化铵模\r\n板剂体系相比，本体系成核诱导期较短，生长速率较快；n（NaF）／n\r\n（SiO2）值增大时，晶化诱导期缩短，成核速率加快，但氟化钠量过高\r\n时，成核速率反而降低，n（NaF）／n（SiO2）最佳值为0．10～0．17\r\n；较高的OH－／SiO2比有利于缩短晶化诱导期．     

钛硅分子筛TS-1合成晶化气氛的影响

考察了不同晶化气氛(N2、H2、A ir、O2)对合成钛硅分子筛TS-1的影响,用XRD、IR和N2吸附/脱附对所合成的钛硅分子筛进行结构表征,发现在H2气氛下合成的TS-1结晶度最高,锐钛矿的含量最少;O2气氛下合成的TS-1中锐钛矿含量最高.以氯丙烯氧化为模型反应,考察了不同晶化气氛下合成的钛硅分子筛的催化活性和双氧水的利用效率.结果表明,在H2气氛下所合成的钛硅分子筛的双氧水的利用效率最高.     

无机SiO2-TiO2前驱体体系合成高性能TS-1分子筛

 在热处理条件下,使Ti(SO4)2在多孔硅胶表面自发分散形成具有类似于钛硅分子筛催化活性中心结构单元的Si-O-Ti键的SiO2 -TiO2前驱体,将该前驱体在模板剂四丙基氢氧化铵的作用下水热晶化得到了钛硅分子筛TS-1. X射线衍射、红外光谱和扫描电镜表征表明, TS-1分子筛晶化完全,钛原子已进入TS-1分子筛骨架. 苯酚羟基化反应测试结果表明,前驱体的热处理温度对合成的TS-1分子筛的催化性能影响很大,处理温度以450 ℃为宜.     

ZSM-5、ZSM-57分子筛和丝光沸石间的转晶规律

考察了硅铝比、碱度、有机胺模板剂、晶化时间及温度等合成条件对ZSM-5、ZSM-57 分子筛和丝光沸石之间相互转晶的影响. 发现较高的碱度、较长的晶化时间有利于合成丝光沸石；较低的碱度、较高的诱导晶化温度、较长的晶化时间有利于合成低硅铝比的ZSM-57 分子筛；合成低硅铝比的ZSM-5分子筛则需要在能合成丝光沸石和ZSM-57 分子筛的碱度区间内精确调节碱度, 缩短晶化时间、降低诱导晶化温度、加入适当晶种, 有利于合成低硅铝比的ZSM-5 分子筛. 合成条件稍微改变, 会导致各种沸石之间发生转晶, 晶化产物出现两种或两种以上的晶型.     

用高效NaY沸石导向剂快速合成A型沸石

提出了应用高效NaY沸石导向剂快速合成A型沸石的新方法. 在合成过程中, NaY沸石导向剂提供了全部硅源(无需另加硅源). 与用水玻璃提供硅源的合成方法相比, 该法晶化速度快, 合成温度低, 并可在低碱度条件下合成超细A型沸石. 29Si NMR表征和UV Raman研究表明, 高效NaY沸石导向剂中含有大量的六元环等低分子量硅铝酸根前驱体, 它们有利于A型沸石成核与晶体生长.     

无机原料体系合成TS-1影响因素的研究

以廉价的硅溶胶和三氯化钛分别作为硅源和钛源,四丙基溴化铵(TPABr)为模板剂,二乙胺、正丁胺、氨水等作为碱源,在无机体系中合成了TS-1分子筛。采用XRD,IR,UV-vis,SEM,元素分析和N2吸附/脱附等对合成的分子筛进行了表征。详细考察了碱源、硅钛比N2保护、晶种、模板剂用量、硅源及晶化时间等因素对分子筛合成的影响。结果表明,以无机原料合成的TS-1与用传统有机原料合成的TS-1具有同样的特征。碱度的控制是合成的关键,配胶时需N2保护,加入晶种对合成有明显的导向作用,模板剂最低用量有一临界值,硅溶胶作硅源合成的TS-1晶粒比较大。     

无机原料体系合成TS-1影响因素的研究

以廉价的硅溶胶和三氯化钛分别作为硅源和钛源,四丙基溴化铵(TPABr)为模板剂,二乙胺、正丁胺、氨水等作为碱源,在无机体系中合成了TS-1分子筛。采用XRD,IR,UV-vis,SEM,元素分析和N2吸附/脱附等对合成的分子筛进行了表征。详细考察了碱源、硅钛比N2保护、晶种、模板剂用量、硅源及晶化时间等因素对分子筛合成的影响。结果表明,以无机原料合成的TS-1与用传统有机原料合成的TS-1具有同样的特征。碱度的控制是合成的关键,配胶时需N2保护,加入晶种对合成有明显的导向作用,模板剂最低用量有一临界值,硅溶胶作硅源合成的TS-1晶粒比较大。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.